i-Vac iVAC Pro Manuale utente
REMOTE USER GUIDE
www. switch.com
MBright Tools iVAC Inc.
5570 Jill Street.Box 557.Osgoode, Ontario Canada.K0A 2W0
Tel: 613 826 2200 .Fax: 613 826 3300.info@iVacSwitch.com
Table of Contents
1 Warnings
2 Physical Features
3 General Description
4 System Address
5 Tool Address
6 Replacing Batteries
7Specications
8 Regulatory Approval
1 Warnings
Please read the operating instructions before use.
The iVAC Pro Remote is intended for indoor use
in dry locations only. Used batteries should be
disposed of in a safe manner.
2 Physical Features
DIP
Program
Switch
CR2032
Batteries
Belt Clip
3 General Description
The ‘iVAC Pro Remote’ operates in conjunction
with an ‘iVAC Pro Switch’ and enables a dust
collector to be controlled remotely, by means of a
manual operation.
When the ON button is pressed, a radio
frequency transmission is sent to the ‘iVAC Pro
Switch’ instructing it to turn on and provide
power to the dust collector. When the OFF button
is pressed, the power will be removed from the
dust collector.
To ensure consistent operation, it is
recommended that the buttons are operated for
one to two seconds.
The ‘iVAC Pro Remote’ can be programmed
by means of an internal DIP Program Switch to
operate on one of four System Addresses and
one of eight Tool Addresses, similar to an ‘iVAC
Pro Tool’. (Refer to iVAC Pro System User Guide
supplied with the iVAC Pro Switch)
The iVAC Pro Remote is housed in a plastic case
90mm x 70mm x 25mm.
An easily attached belt clip is also provided.
The rear cover is attached by three screws.
Removing the cover allows access to the
batteries and the DIP Program Switch.
This allows the batteries to be changed and
also to program address functions of the ‘iVAC
Pro Remote’ by means of the six position DIP
Program Switch.
There are two address functions, System Address
and Tool Address.
4 System Address
A System consists of an’ iVAC Pro Switch’ and
from one to eight iVAC Pro Tools or iVAC Pro
Remotes. There can be any mix of Tools or
Remotes.
By means of positions S1 and S2 of the DIP
Program Switch, the Remote can be assigned to
work on one of four System Addresses, A, B, C
or D.
The System Address enables up to four
Systems to operate independently while within
communication range of each other.
System Address
*factory setting
S1 S2
*A Off Off
B On Off
C Off On
D On On
5 Tool Address
Each iVAC Pro Remote or iVAC Pro Tool must
be assigned an independent one of eight Tool
Addresses. This information is used by the iVAC
Pro Switch to enable it to know the status of each
individual iVAC Pro Tool or iVAC Pro Remote in
the System. The Tool Address is set by means of
positions S3, S4 and S5 of the Program Switch.
S6 is not used.
Tool Address
*factory setting
S3 S4 S5
1 On Off Off
2 Off On Off
3 On On Off
4 Off Off On
5 On Off On
6 Off On On
*7 On On On
8 Off Off Off
6 Replacing the Batteries
The batteries have a useful life of 25,000
operations over a 3 year period.
To remove the batteries it is recommended to use
the tip of a pen or similar device and push from
the inside edge of the battery holder.
When replacing CR2032 batteries, both batteries
should be replaced at the same time. The
positive (+) side of the battery should face away
from the circuit board.
Altri manuali per iVAC Pro
3
Indice
Lingue:
Altri manuali i-Vac Telecomando
