i3 International i3F416U Manuale utente
i3F416U (with UTP Balun)
Wide Dynamic Range Dome User Guide
CONTENTS
PRECAUTIONS
NOTES OF USE
CEILING MOUNT I
NSTALLATION
WALL MOUNT I
NSTALLATION
OSD MENU
OSD SETTINGS
SPECIFICATIONS
1
2
6
8
11
13
19
WARNING:
Before attempting to connect or operate this product, read these instructions carefully.
Save this manual for future use.
To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the camera.
Refer servicing to qualified personnel only.
1
PRECAUTIONS
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause
harmful interference, in which case users will be required to correct the
interference at their own expense.
FCC Caution:
To ensure continued compliance, use only shielded interface cables
when connecting to computer or peripheral devices. Any changes
or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
The serial number of this product may be found on top of the unit. It is
recommended that you note the serial number of this unit in the space
provided and retain this book as a permanent record of your purchase to
aid identication in the event of theft.
Model No.
Serial No.
Date of Purchase:
2
Features
• Rugged, Vandal-resistant, IP67
•Wide dynamic range color camera with auto iris, 2.8-10mm varifocal
lens
•Available with wide dynamic range(WDR) technology
(102dB typical / 120dB max)
•1/3” Pixim Orca sensor
•Noise ratio > 50dB
•Available with lowlight DSS (digital slow shutter) technology
•WDR model include both composite and unshielded Twisted pair
(UTP) output and progressive scan
•Gamma correction
•AGC
•Slow shutter up to 32x
•Power supply: 12VDC / 24VAC
•Ceiling mount or wall mount
Troubleshooting
The following conditions may be observed when using this camera.
These are inherent in the design and do not stem from any fault in the
camera itself.
• Vertical smear This phenomenon occurs when viewing a very
bright object.
• Patterned noise
This is a xed pattern, which may appear over the
entire monitor screen when the camera is operated
at a high temperature or in a low-light environment.
• Jagged picture When viewing stripes, straight lines, or similar pat-
terns, the image on the screen may appear jagged.
NOTES OF USE
3
Power Supply
You can use either AC 24V or DC 12V power input. The camera auto-
matically detects the power. When connecting the transformer, be sure
to connect each lead to the appropriate terminal. Incorrect connection
may cause malfunction and/or damage to the video camera.
Operating or storage location
Avoid shooting very bright objects (such as light ttings) for an extended
period. Avoid operating or storing the unit in the following locations:
• Extremely hot or cold places (operating temperature: -10oC to +50oC)
•Close to sources of strong magnetism
• Close to sources of powerful electromagnetic radiation, such as
radios or TV transmitters
•Close to humid or excessively dusty places
•Where exposed to mechanical vibrations
• Close to uorescent lamps or objects reecting light
• Under unstable light sources (may cause ickering)
Attaching the dome casing
Attach the dome casing with the screw provided.
Transportation
When transporting the camera, repack it as originally packed at the
factory, or in materials equal in quality.
Cleaning
• For maximum optical clarity, the dome cover must remain clean. Use
a soft, dry cloth to remove nger prints or dust from the dome cover.
•Use a blower to remove dust from the lens.
•Clean the body with a soft, dry cloth. If it is very dirty, use a cloth
dampened with a small quantity of neutral detergent, then wipe dry.
•Do not use volatile solvents such as alcohol, benzene, or thinners,
as they may damage the surface nishes.
Ensuring Water Resistance
Wrap the connections (threads) between pipes with waterproof adhesive/tape to
prevent water/moisture from entering.
NOTES OF USE
4
NOTES OF USE
Using the Camera Outdoors
To prevent moisture from getting inside the casing, use sealant (e.g., silicon
sealant) to seal the following areas:
• The holes under the unit casing that is attached to a ceiling or wall.
• Conduit holes on the side and bottom of the unit casing. You can seal these
using a water-proof accessory.
• Joint surface of the camera casing gasket and unit casing.
Location and Function of Parts
1. Unit casing
The unit casing is made of die-cast aluminum and has conduit holes on
the side and bottom.
2. Safety cord
The safety cord prevents the dome casing from falling. To avoid personal
injury and liability, do not remove the safety cord from the unit. If it is
necessary to remove the cord, remember to fasten the screws provided.
3. Zoom & Focus lever
Adjusts the camera range and focus. The lever itself is a screw and can be
removed. Turning this screw completely clockwise locks the position.
4. UTP-Unshield Twisted Pair (white/black wire)
Twisted Pair (TP) terminal (CAT.5E) for video signal. Usage of TP output
requires a TP receiver at the other end of the TP line.
5. Power connector (red/black wire)
Connects to the external power source. (DC12V/AC24V)
6. BNC connector
Connects to the VIDEO IN connector of the Monitor Video Connector
7. Multi-Function switch
Press the multi-function switch for 2 or more seconds and the OSD setup
menu will display on the monitor. Use the multi-function switch to select
desired item and change the settings of the selected item.
8. Monitor (MONITOR OUT) connector
You can connect to an external monitor from this connector. This will allow
you to adjust the camera while looking at the image on the monitor. After
adjusting the camera, disconnect the cable.
5
1
2
3
456
NOTES OF USE
7
8
6
CEILING MOUNT INSTALLATION
Step 2:
Install the camera onto the ceiling
and fasten securely using the
screws provided.
Step 3:
Remove the mask. Rotate the
main bracket to adjust the pan
angle.
Step 1:
Adhere the guide pattern to the
installation surface. Drill one big
and three small holes, using the
template as a guide.
7
CEILING MOUNT INSTALLATION
Step 4:
Loosen the screw on the main
bracket, adjust the tilt angle, then
tighten the screw to maintain
setting.
Step 5:
Adjust the camera zoom to a
suitable position.
Step 6: Return mask to
its original position on the
camera. Screw the top cover
to the camera securely.
8
WALL MOUNT INSTALLATION
Step 2:
Fasten the bottom casing to the
wall by securely tightening the
four screws provided.
Step 3:
Install the camera onto the
bottom casing and secure tightly
with screws.
Step 1:
Adhere the guide pattern to the
installation surface. Drill four
small holes for the plastic drywall
anchors.
Indice
Altri manuali i3 International Telecamera di sicurezza
i3 International
i3 International Am57 Manuale utente
i3 International
i3 International Ax46 Series Manuale utente
i3 International
i3 International Ax32VD14 Manuale utente
i3 International
i3 International Ax49D Manuale utente
i3 International
i3 International Ax47DC Manuale utente
i3 International
i3 International i3R363 Manuale utente
i3 International
i3 International Ax85 Manuale utente
i3 International
i3 International Ax47R4 Manuale utente
i3 International
i3 International Am42 Series Manuale utente
i3 International
i3 International Ax46-series Manuale utente
i3 International
i3 International Ax63Z Series Manuale utente
i3 International
i3 International C-AX401D1M Manuale utente
i3 International
i3 International Ax45RM series Manuale utente
i3 International
i3 International Am73 Manuale utente
i3 International
i3 International Ax61 series Manuale utente
i3 International
i3 International Ax47R series Manuale utente
i3 International
i3 International Ax63Z Series Manuale utente
i3 International
i3 International Annexxus 52C Manuale utente
i3 International
i3 International Ax47R series Manuale utente
i3 International
i3 International Ax32V Series Manuale utente
