IBM Eserver 7210 Manuale

7210 Model 025 External DVD–RAM Drive

7210 Model 025 DVD-RAM Drive

Setup and Operator Guide

SY44-0079-00



7210 Model 025 External DVD–RAM Drive

7210 Model 025 DVD-RAM Drive

Setup and Operator Guide

SY44-0079-00



Note!

Before using this information and the product it supports, be sure to read the general information

under “Notices” on page v.

First Edition (May 2001)

This edition, SY44–0079–00, applies to Model 025 of the 7210 External DVD-RAM Drive and to all subsequent

releases and modifications until otherwise indicated in new editions. This edition applies only to the specified

model of the device.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Contents

Notices ...............v

Safety and Environmental Notices .......vi

Danger Notices ............vi

Caution Notices ............vii

Attention Notices ...........vii

Product Recycling and Disposal ......vii

Battery Return Program .........vii

Environmental Design..........vii

Electronic Emission Notices.........viii

Federal Communications Commission (FCC)

Statement..............viii

Trademarks...............x

About This Guide ..........xi

Related Publications ...........xi

How to send your comments ........xii

Chapter 1. General Information .....1

System Requirement............1

RS/6000 or pSeries Systems ........2

AS/400 or iSeries Systems .........2

SCSI Bus Cables .............2

Specifications ..............2

Chapter 2. Setting Up the 7210

DVD-RAM Drive ...........3

Performing the Installation .........3

Step 1. Using the Inventory Checklist .....3

Step 2. Checking the Electrical Outlets .....4

Step 3. Assembling the Materials ......4

Step 4. Determining the SCSI Address (for

RS/6000 or pSeries Systems Only) ......4

Step 5. Setting the SCSI Address.......6

Step 6. Placing the 7210 DVD-RAM Drive . . . 7

Step 7. Performing a System Shutdown ....7

Step 8. Connecting the SCSI Bus Cable ....8

Step 9. Installing the SCSI Bus Terminator . . . 8

Step 10. Connecting the Power Cables ....10

Step 11. Performing the Checkout Procedure . . 11

Chapter 3. Using the 7210 DVD-RAM

Drive ...............13

Operator Controls ............13

Power Switch.............13

Load/Unload Button ..........13

Manual Unload Hole ..........13

Volume Control ............14

Headphone Jack ............14

Audio Jacks .............14

Indicator Lights .............14

Power-On Light ............14

Status Light .............14

Loading and Unloading a DVD-RAM Disc ....15

Loading a Disc ............15

Unloading a Disc ...........15

Cleaning the DVD-RAM Drive ........15

Chapter 4. Removing the 7210

DVD-RAM Drive ...........17

Removal Checklist ............17

Appendix. Power Cables .......19

iv 7210 DVD-RAM Drive Setup and Operator Guide

Notices

This information was developed for products and services offered in the U.S.A.

IBM may not offer the products, services, or features discussed in this document in

other countries. Consult your local IBM representative for information on the

products and services currently available in your area. Any reference to an IBM

product, program, or service is not intended to state or imply that only that IBM

product, program, or service may be used. Any functionally equivalent product,

program, or service that does not infringe any IBM intellectual property right may

be used instead. However, it is the user’s responsibility to evaluate and verify the

operation of any non-IBM product, program, or service.

IBM may have patents or pending patent applications covering subject matter

described in this document. The furnishing of this document does not give you

any license to these patents. You can send license inquiries, in writing, to:

IBM Director of Licensing

IBM Corporation

500 Columbus Avenue

Thornwood, NY 10594

U.S.A.

For license inquiries regarding double-byte (DBCS) information, contact the IBM

Intellectual Property Department in your country or send inquiries, in writing, to:

IBM World Trade Asia Corporation

Licensing

2-31 Roppongi 3-chome, Minato-ku

Tokyo 106-0032, Japan

The following paragraph does not apply to the United Kingdom or any other

country where such provisions are inconsistent with local law:

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS

PUBLICATION “AS IS”WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or

implied warranties in certain transactions, therefore, this statement may not apply

to you.

This information could include technical inaccuracies or typographical errors.

Changes are periodically made to the information herein; these changes will be

incorporated in new editions of the publication. IBM may make improvements

and/or changes in the product(s) and/or the program(s) described in this

publication at any time without notice.

Any references in this information to non-IBM Web sites are provided for

convenience only and do not in any manner serve as an endorsement of those Web

sites. The materials at those Web sites are not part of the materials for this IBM

product and use of those Web sites is at your own risk.

Any performance data contained herein was determined in a controlled

environment. Therefore, the results obtained in other operating environments may

vary significantly. Some measurements may have been made on development-level

systems and there is no guarantee that these measurements will be the same on

generally available systems. Furthermore, some measurement may have been

estimated through extrapolation. Actual results may vary. Users of this document

should verify the applicable data for their specific environment.

Information concerning non-IBM products was obtained from the suppliers of

those products, their published announcements or other publicly available sources.

IBM has not tested those products and cannot confirm the accuracy of

performance, compatibility or any other claims related to non-IBM products.

Questions on the capabilities of non-IBM products should be addressed to the

suppliers of those products.

All statements regarding IBM’s future direction or intent are subject to change or

withdrawal without notice, and represent goals and objectives only.

This information contains examples of data and reports used in daily business

operations. To illustrate them as completely as possible, the examples include the

names of individuals, companies, brands, and products. All of these names are

fictitious and any similarity to the names and addresses used by an actual business

enterprise is entirely coincidental.

If you are viewing this information softcopy, the photographs and color

illustrations may not appear.

The drawings and specifications contained herein shall not be reproduced in whole

or in part without the written permission of IBM.

IBM has prepared this publication for use by customer personnel for operating and

planning for the specific machines indicated. IBM makes no representations that it

is suitable for any other purpose.

Safety and Environmental Notices

Danger Notices

A danger notice calls attention to a situation that is potentially lethal or extremely

hazardous to people.

Use the following danger notices throughout this book.

DANGER

To prevent a possible electrical shock from touching two surfaces with

different electrical grounds, use one hand, when possible, to connect or

disconnect signal cables. (RSFTD004)

DANGER

An electrical outlet that is not correctly wired could place hazardous voltage

on metal parts of the system or the products that attach to the system. It is the

customer’s responsibility to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock. (RSFTD201)

vi 7210 DVD-RAM Drive Setup and Operator Guide

DANGER

To prevent a possible electrical shock when adding or removing any devices

to or from the system, ensure that the power cords for those devices are

unplugged before the signal cables are connected or disconnected. If possible,

disconnect all power cords from the existing system before you add or

remove a device. (RSFTD203)

DANGER

To prevent a possible electrical shock when installing the device, ensure that

the power cord for that device is unplugged before installing signal cables.

(RSFTD204)

Caution Notices

A caution notice calls attention to a situation that is potentially hazardous to

people because of some existing condition.

Use the following caution notices throughout this book.

CAUTION:

Do not remove the covers of the unit. An invisible laser beam may be present.

The repair of this unit should be performed by trained service personnel only.

(RSFTC242)

Attention Notices

An attention notice indicates the possibility of damage to a program, device,

system, or data.

Product Recycling and Disposal

Components of the system, such as structural parts and circuit cards, can be

recycled where recycling facilities exist. IBM does not currently collect and recycle

used IBM products from customers in the United States other than those products

that are involved in trade-in programs. Companies are available to disassemble,

reutilize, recycle, or dispose of electronic products. Contact an IBM account

representative for more information.

The system unit contains batteries and circuit boards with lead solder. Before you

dispose of this unit, these batteries and circuit boards must be removed and

discarded according to local regulations or recycled where facilities exist. This book

contains specific information on each battery type where applicable.

Battery Return Program

In the United States, IBM has established a collection process for reuse, recycling,

or proper disposal of used IBM batteries and battery packs. For information on

proper disposal of the batteries in this unit, please contact IBM at 1-800-426-4333.

Please have the IBM part number that is listed on the battery available when you

make your call. For information on battery disposal outside the United States,

contact your local waste disposal facility.

Environmental Design

The environmental efforts that have gone into the design of the system signify

IBM’s commitment to improve the quality of its products and processes. Some of

Notices vii

these accomplishments include the elimination of the use of Class I

ozone-depleting chemicals in the manufacturing process, reductions in

manufacturing wastes, and increased product energy efficiency. For more

information, contact an IBM account representative.

Electronic Emission Notices

The following Statement applies to this IBM product. The statement for other IBM

products intended for use with this product will appear in their accompanying

manuals.

Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the limits for a

class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

vReorient or relocate the receiving antenna.

vIncrease the separation between the equipment and receiver.

vConnect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

vConsult an IBM authorized dealer or service representative for help.

Properly shielded and grounded cables and connectors must be used in order to

meet FCC emission limits. Proper cables and connectors are available from IBM

authorized dealers. IBM is not responsible for any radio or television interference

caused by using other than recommended cables or connectors or by unauthorized

changes or modifications to this equipment. Unauthorized changes or

modifications could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interferences, and

(2) this device must accept any interferences received, including interference that

may cause undesired operation.

Responsible Party:

International Business Machines Corporation

New Orchard Road

Armonk, NY 10504

Telephone: 1-919-543-2193

Industry Canada Compliance Statement

This Class B digital apparatus meets the requirements of the Canadian

Interference-Causing Equipment Regulations.

Avis de conformitéàla réglementation d’Industrie Canada

viii 7210 DVD-RAM Drive Setup and Operator Guide

Altri manuali per eserver 7210

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali IBM Hardware per computer

IBM

IBM PowerPC 405GP Manuale utente

IBM

IBM BladeCenter Management Module Manuale utente

IBM

IBM 6611 Manuale utente

IBM

IBM 3301690 Manuale utente

IBM

IBM iSeries 5075 Istruzioni utente

IBM

IBM 55PUS8118 SCSI-2 Manuale utente

IBM

IBM Redbooks 2/4 Port Ethernet Expansion Card Manuale utente

IBM

IBM Power S1014 Manuale utente

IBM

IBM S922 Manuale di istruzioni

IBM

IBM QLogic 4Gb Fibre Channel Expansion Card Manuale utente

IBM

IBM PN 10K8798 Manuale utente

IBM

IBM THINKCENTER 8128 Manuale del proprietario

IBM

IBM 9040-MR9 Manuale utente

IBM

IBM WebSphere DataPower XC10 Manuale utente

IBM

IBM 1 GB Microdrive Storage Card Manuale utente

IBM

IBM WebSphere Business Integration Adapter Manuale utente

IBM

IBM 5280 Manuale

IBM

IBM 7133 D40 Manuale utente

IBM

IBM WebSphere DataPower 7198 Manuale utente

IBM

IBM 0367 Manuale utente

IBM

IBM M791 Series Manuale utente

IBM

IBM MPC603EC Manuale utente

IBM

IBM Power Systems 8247-42L Manuale utente

IBM

IBM System x3630 M4 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

IBM eserver 7210 Manuale

Manuali Hardware per computer popolari di altre marche