ICM Controls SC 3006 Istruzioni generali
Auto Changeover
7-Day Programmable
Hardwired
SC 3006
Programmable Electronic Thermostat
Installation, Operation & Application Guide
For more information on our complete range of American-made
products – plus wiring diagrams, troubleshooting tips and more,
visit us at www.icmcontrols.com
• 7-Day Programmable
•
Single Stage Heat Pump/Non-Heat Pump Systems
• Backlit Display
•
Single Stage Heat/Cool Systems
•
Field Calibration
•
Auto Changeover
•
Button Lockout Function
•
Compatible with Gas, Oil, or Electric
• Simpleset
®
Programming
• Remote Temperature Sensor Capability
• Title 24 Compliant / No Batteries Required
• Relay Outputs
(minimum voltage drop in thermostat)
• Ideally Suited for:
– Residential (New Construction/Replacement),
Light Commercial
Table of Contents
Specifications ........................................................................................................................1
Important Safety Information ...............................................................................................1
Package Contents/Tools Required.........................................................................................1
To Remove Existing Thermostat ..........................................................................................2
To Install Thermostat ............................................................................................................2
Remote Sensor Installation (Optional) ..................................................................................4
Wiring Diagrams....................................................................................................................5
Configuration Mode...............................................................................................................8
Starting the Thermostat .....................................................................................................10
Testing the Thermostat ......................................................................................................11
Mode of Operation ..............................................................................................................12
Operating Modes ................................................................................................................13
Setting the Time and Day of the Week ...............................................................................14
Programming ......................................................................................................................15
Simpleset®Programming ....................................................................................................17
Lockout Function ................................................................................................................17
Factory Preprogramming ....................................................................................................18
Personal Program Schedule ................................................................................................18
Troubleshooting ..................................................................................................................20
1
Electrical Rating: • 24 VAC (18 to 30 VAC) • 1 amp maximum per terminal
• 3 amp maximum total load
Temperature control ranges: 45°F to 90°F Accuracy: ± 1°F
System configurations: 1-stage heat, 1-stage cool, heat pump, gas, oil, electric
Timing: Anti-short Cycle: 5 minutes
Backlight Operation: 10 seconds
Terminations: C, RH, RC, W, Y, B, O, G, S1, S2
Specications
WARNING!
: Always turn off power at the main power supply before installing, cleaning, or removing
thermostat.
• This thermostat is for 24 VAC applications only; do not use on voltages over 30 VAC
• Do not short across terminals of gas valve or system control to test operation; this will damage your
thermostat and void your warranty
• All wiring must conform to local and national electrical and building codes
• Do not use air conditioning when the outdoor temperature is below 50 degrees; this can damage your
A/C system and cause personal injuries
• Use this thermostat only as described in this manual
Important Safety Information
Package includes: SimpleComfort®3006 programmable thermostat on base, labeled thermostat cover,
wiring labels, screws and wall anchors, Installation, Operation and Application Guide.
Tools required for installation: drill, hammer, screwdriver.
Package Contents/Tools Required
2
To Remove Existing Thermostat
ELECTRICAL SHOCK HAZARD – Turn off power at the main service panel by removing the fuse
or switching the appropriate circuit breaker to the OFF position before removing the existing
thermostat.
1. Turn off power to the heating and cooling system by removing the fuse or switching the appropriate
circuit breaker off.
2. Remove cover of old thermostat. This should expose the wires.
3. Label the existing wires with the enclosed wire labels before removing wires.
4. After labeling wires, remove wires from wire terminals.
5. Remove existing thermostat base from wall.
6. Refer to the following section for instructions on how to install this thermostat.
To Install Thermostat
ELECTRICAL SHOCK HAZARD – Turn off power at the main service panel by removing the fuse
or switching the appropriate circuit breaker to the OFF position before removing the existing
thermostat.
IMPORTANT: Thermostat installation must conform to local and national building and electrical
codes and ordinances.
Note:
Mount the thermostat about five feet above the floor. Do not mount the thermostat on an
outside wall, in direct sunlight, behind a door, or in an area affected by a vent or duct.
1. Turn off power to the heating and cooling system by removing the fuse or switching the appropriate
circuit breaker off.
3
To Install Thermostat (continued)
2. To remove cover, insert and twist a coin or screwdriver in the slots on the sides of the thermostat.
3. Put thermostat base against the wall where you plan to mount it (Be sure wires will feed through the
wire opening in the base of the thermostat).
4. Mark the placement of the mounting holes.
5. Set thermostat base and cover away from working area.
6. Using a 3/16” drill bit, drill holes in the places you have marked for mounting.
7. Use a hammer to tap supplied anchors in mounting holes.
8. Align thermostat base with mounting holes and feed the control wires through wire opening.
9. Use supplied screws to mount thermostat base to wall.
10. Insert stripped, labeled wires in matching wire terminals. See “Wiring Diagrams” section of this
manual (Page 5).
CAUTION!
:
Be sure exposed portion of wires does not touch other wires.
11. Tighten screws on terminal block. Gently tug wire to be sure of proper connection. Double check that
each wire is connected to the proper terminal.
12. Seal hole for wires behind thermostat with non-flammable insulation or putty.
13. Set Gas/Electric switch. Set to gas for oil or gas systems. Set to electric for heat pumps or electric
heat systems.
14. Replace cover on thermostat by snapping it in place.
15. Turn on power to the system at the main service panel.
16. Test thermostat operation as described in “Testing the Thermostat” (Page 11).
4
1. Remove cover from remote sensor housing.
2. Select an appropriate location for mounting the remote sensor.
3. Mount remote sensor unit using hardware provided.
4. Install two strand shielded wire between remote sensor and thermostat. Shielded wire must be used.
Do not run remote sensor wire in conduit with other wires.
• Wire 1 should run between the S1 terminal on the thermostat and the S1 terminal on the
remote sensor
• Wire 2 should run between the S2 terminal on the thermostat and the S2 terminal on the
remote sensor
• Connect the shielding of the wire to the S2 terminal on the thermostat
5. Disable the main sensor (R12) on the thermostat by cutting it from the circuit board.
Remote Sensor Installation (Optional)
5
Wiring Diagrams
Fan
Control
4 or 5 Wire,
Fan
Control
6
7
8
The configuration mode is used to set the SC3006 to match your heating/cooling system. The SC3006 functions
with heat pump, air conditioning, gas, oil or electric heat systems.
1. To enter the configuration mode, simultaneously hold down the and buttons while the SC3006 is in OFF mode.
2. Press the or button to change settings within each screen.
3. Press the button to advance to the next screen.
Note: The button will return you to the previous screen.
4. To exit configuration mode, hold the button for 6 seconds.
Configuration Mode Settings
The setup screens for configuration mode are as follows:
1. Temperature scale (F or C) – Choose Fahrenheit or Celsius.
Press the or button to select.
Press the button to advance to the next screen.
2. Differential (1°F - 5°F) (1°C - 3°C) – Set the number of degrees between your “turn on”
temperature and your “setpoint” temperature.
Press the or button to set differential value.
Press the button to advance to the next screen.
3. Deadband (1°F - 9°F) (1°C - 5°C) – Set the minimum number of degrees between your heating
system activation and your cooling system activation.
Press the or button to set deadband value.
Press the button to advance to the next screen.
Conguration Mode
Indice
Altri manuali ICM Controls Termostato
ICM Controls
ICM Controls SC4011 Manuale utente
ICM Controls
ICM Controls SC 2001 Istruzioni generali
ICM Controls
ICM Controls SC1901L Istruzioni generali
ICM Controls
ICM Controls SC2000L Istruzioni generali
ICM Controls
ICM Controls SC2211 Istruzioni generali
ICM Controls
ICM Controls SC2311L Istruzioni generali
ICM Controls
ICM Controls SC700LV Manuale utente
ICM Controls
ICM Controls SC2201 Istruzioni generali
ICM Controls
ICM Controls SC 4811 Istruzioni generali
ICM Controls
ICM Controls SC 3201 Istruzioni generali
ICM Controls
ICM Controls SC2201 Istruzioni generali
ICM Controls
ICM Controls SC3000L Manuale utente
ICM Controls
ICM Controls SC 4811 Istruzioni generali
ICM Controls
ICM Controls SC 2210 Istruzioni generali
ICM Controls
ICM Controls SC 3000 Istruzioni generali
ICM Controls
ICM Controls SC3000L Istruzioni generali
ICM Controls
ICM Controls SC4812 Manuale utente
ICM Controls
ICM Controls SC 4211 Istruzioni generali
ICM Controls
ICM Controls SC 5811 Manuale utente
ICM Controls
ICM Controls SC1600L Istruzioni generali
