Icom IC-2200H Manuale utente

QUICK REFERENCE GUIDE

■Installation

DLocation

Select a location which can support the weight of the trans-

ceiver and does not interfere with driving in any way. We rec-

ommend the locations shown in the diagram below.

NEVER place the transceiver where normal operation of the

vehicle may be hindered or where it could cause bodily injury.

NEVER place the transceiver where air bag deployment may

be obstructed.

DO NOT place the transceiver where hot or cold air blows di-

rectly onto it.

AVOID placing the transceiver in direct sunlight.

DUsing the mounting bracket

➀Drill 4 holes where the mounting bracket is to be installed.

•Approx. 5.5–6 mm (1⁄4″) when using nuts; approx. 2–3 mm (1⁄8″)

when using self-tapping screws.

➁Insert the supplied screws, nuts and washers through the

mounting bracket and tighten.

➂Adjust the angle for the clearest view of the function dis-

play.

IMPORTANT!

Detailed installation notes for Icom mobile transceivers to

be fitted into vehicles are available. Contact your Icom

dealer or distributor.

Nut

Spring washer

Flat washer

When using

self-tapping

screws

Spring

washer

Mounting

nut

Mounting

bracket

QUICK REFERENCE GUIDE

DBattery connection

☞NEVER connect the transceiver directly to a 24 V battery.

☞DO NOT use the cigarette lighter socket for power con-

nections. (See p. 5 for details)

Attach a rubber grommet when passing the DC power cable

through a metal plate to prevent short circuiting.

•CONNECTING TO A DC POWER SOURCE

•See p. 90 for fuse replacement.

DDC power supply connection

Use a 13.8 V DC power supply with at least 15 A capacity.

Make sure the ground terminal of the DC power supply is

grounded.

•CONNECTING TO A DC POWER SUPPLY

•See p. 90 for fuse replacement.

DC power

supply 13.8 V

to an

outlet

Fuses

20 A

black

red⊕

−

⊕

−

IC-2200H

Fuses

20 A

Crimp Solder

black

red⊕

Grommet

IC-2200H

−

12 V 12 V

battery Supplied

DC power cable

NOTE:

Use terminals for the

cable connections.

+red

_black

III

QUICK REFERENCE GUIDE

DAntenna installation

•Antenna location

To obtain maximum performance from the transceiver, select

a high-quality antenna and mount it in a good location. A non-

radial antenna should be used when using a magnetic mount.

•Antenna connector

The antenna uses a PL-259 connector.

•PL-259 CONNECTOR

qSlide the coupling ring

down. Strip the cable

jacket and soft solder.

wStrip the cable as shown

at left. Soft solder the cen-

ter conductor.

eSlide the connector body

on and solder it.

rScrew the coupling ring

onto the connector body.

(10 mm ≈3⁄8 in)

NOTE: There are many publications covering proper an-

tennas and their installation. Check with your local dealer

for more information and recommendations.

DConnecting a microphone

Connect a microphone to the eight-pin modular socket on the

front panel of the transceiver.

*HM-133V; A different microphone may be

supplied with some versions of the IC-2200H.

30 mm

10 mm (soft solder)

10 mm

1–2 mm

solder solder

Soft

solder

Coupling ring

to antenna

Roof-mount antenna

(Drill a hole or use a magnetic mount.)

Gutter-mount antenna

Trunk-mount

antenna

QUICK REFERENCE GUIDE

■Your ﬁrst contact

Now that you have your IC-2200H installed in your car or

shack, you are probably excited to get on the air. We would

like to take you through a few basic operation steps to make

your ﬁrst “On The Air” an enjoyable experience.

1. Turning ON the transceiver

Before powering up your IC-2200H, you may want to make

sure the audio volume and squelch level controls are set in

9–10 o’clock positions.

Although you have purchased a brand new transceiver, some

settings may be changed from the factory defaults because

of the QC process. Resetting the CPU is necessary to start

from factory default.

➥While pushing [SET ] and [S.MW ], push

[PWR] for 1 sec. to reset the CPU.

2. Tune the desired frequency

[DIAL] will allow you to dial in the frequency you want to op-

erate. Pages 9 and 11 will instruct you on how to set the tun-

ing speed.

Using the HM-133V

You can directly enter the frequency with the HM-133V keypad.

We hope these pointers have been helpful. Now you

are ready to call CQ.

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

[EXAMPLE]: Setting frequency to 145.3625 MHz.

Push

[DIAL]

MWLOCK

[PWR]

[SET LOCK][S.MW MW]

Set both [VOL] and [SQL] controls to

9–10 o’clock positions.

[VOL]

[SQL]

QUICK REFERENCE GUIDE

■Repeater operation

1. Setting duplex

Push [LOW ] for 1 sec. once or twice to select minus

duplex or plus duplex.

•The USA version has an auto repeater function, therefore, setting

duplex is not required.

2. Repeater tone

Push [TONE ] several times until “ ” appears, if the

repeater requires a subaudible to be accessed.

Using the HM-133V

Plus or minus duplex selection and the repeater tone setting

can be made easily via HM-133V.

Push [

DUP

–7(TONE)] for minus duplex; [

DUP

+8(TSQLSS)]

for plus duplex selection, push [FUNC] then [

DUP

–7(TONE)]

to turn the repeater tone ON.

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

Push

Push , then

Push

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

T-SCAN

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

DUP

The IC-2200H has a total of 207 memory channels (including

6 scan edges and 1 call channel) for storing often used oper-

ating frequency, repeater settings, etc.

1. Setting a frequency

In VFO mode, set the desired operating frequency with re-

peater, tone and tuning steps, etc.

2. Selecting a memory channel

Momentarily push [S.MW ], then rotate [DIAL] to select

the desired memory channel.

•“M” indicator and memory channel number blink.

3. Writing a memory channel

Push and hold [S.MW ] for 1 sec. to program.

•3beeps sound

•Memory channel number automatically increases when continuing

to push [S.MW ] after programming.

Using the HM-133V

qIn VFO mode, set the desired operating frequency, includ-

ing offset direction, tone settings, etc.

wPush [FUNC] then [

CLR

A(MW)].

•“M” indicator and memory channel number blink.

ePush [YY]/[ZZ]to select the desired memory channel.

rPush [FUNC] then push [

CLR

A(MW)] for 1 sec. to pro-

gram.

•3beeps sound

•Memory channel number automatically increases when continu-

ing to push [

CLR

A(MW)] after programming.

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

Push ,

then

LOCK

TANM

MONI DUP

LOW

T-SCAN

TONE PRIO

M/CALL SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

[S.MW MW] [DIAL]

■Programming memory channels

QUICK REFERENCE GUIDE

Altri manuali per IC-2200H

Indice

Manuali Radio popolari di altre marche

EisSound

EisSound KBSound iSelect Manuale utente

Midland

Midland 1001LWX Manuale utente

Konig

Konig HAV-SR41 Manuale utente

Roberts

Roberts exprssion Manuale utente

VDigi

VDigi DD3.0 Manuale utente

Radio Shack

Radio Shack 21-1863 Manuale utente

Roberts

Roberts Stream 207 Manuale utente

Sony

Sony Walkman SRF-M97 Manuale utente

Stanley

Stanley FatMax FMC770 Manuale utente

auna

auna DAB-Radio 10026947 Manuale utente

SOUNDMASTER

SOUNDMASTER UR190 Manuale utente

HYT

HYT TC-320 Manuale utente

auna multimedia

auna multimedia Yellowstone 10026851 Manuale utente

B-Tech

B-Tech GMRS-V2 Manuale utente

Weierwei

Weierwei VEV-V8 Manuale utente

SOUNDMASTER

SOUNDMASTER DAB750 Manuale utente

Telefunken

Telefunken TF-1505 Manuale utente

Makita

Makita LXRM03 Manuale utente