Icom IC-PCR1000 Manuale utente
iPCR1000
INSTRUCTION MANUAL
COMMUNICATIONS RECEIVER FOR COMPUTER
This device complies with Part 15 of the FCC Rules. Operation is sub-
ject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IC-PCR10003.qxd03.1.62:41PMページA
IMPORTANT
READ ALL INSTRUCTIONS and on-line help care-
fully and completely before using the receiver.
SAVE THIS INSTRUCTION MANUAL — This
instruction manual contains important operating instructions
for the IC-PCR1000 COMMUNICATIONS RECEIVER FOR
COMPUTER.
USE antenna(s), such as a well-matched 50 Ωantenna and
feedline. For radio communications, the antenna is of critical
importance, along with sensitivity.
EXPLICIT DEFINITIONS
FEATURES
• USER-SELECTABLE INTERFACE
Users can choose from 3 different operating screens de-
pending on their ability level and preference.
• WIDE FREQUENCY RANGE, MULTI-MODE RECEIVE
The IC-PCR1000 has a wide frequency coverage from 0.5
MHz to 1300 MHz* with all mode receive capability.
* Some frequency ranges are restricted depending on version.
• IF SHIFT
The IF shift function is effective in SSB mode for reducing in-
terference from nearby signals. It does so by electronically
shifting the passband of the IF filter.
• REAL-TIME BANDSCOPE FUNCTION
The real-time bandscope function makes it easy to find busy
frequencies and also easy to observe receive frequency band
conditions. The maximum band width is ±200 kHz.
• NOISE BLANKER • VSC (Voice Scan Control) FUNCTION
• S-METER SQUELCH • HIGH PERFORMANCE PLL
CIRCUIT • A VARIETY OF TUNING STEPS • A VARIETY OF
SCANS • DIGITAL AFC CIRCUIT
Versions of the IC-PCR1000 which display “CE” on the serial
number seal, comply with the essential requirements of the
89/336/EEC directive for Electromagnetic Compatibility.
WORD DEFINITION
RWARNING Personal injury, fire hazard or electric shock
may occur.
CAUTION Equipment damage may occur.
NOTE If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
Icom, Icom Inc. and are registered trademarks of Icom Incorporated
(Japan) in the United States, United Kingdom, Germany, France, Spain, Russia
and/or other countries.
i
IC-PCR10003.qxd03.1.62:41PMページi
ii
PRECAUTION
RWARNING! NEVER connect the receiver to an AC
outlet. This may pose a fire hazard or result in an electric
shock.
NEVER connect other than the specified AC adapter to the
receiver. This connection will ruin the receiver.
NEVER connect the receiver to a power source of more
than 16 V DC such as a 24 V battery. This connection will ruin
the receiver.
NEVER allow children to touch the receiver.
NEVER expose the receiver to rain, snow or any liquids.
DO NOT use or place the receiver in areas with tempera-
tures below 0°C (+32°F) or above +50°C (+122°F) or, in
areas subject to direct sunlight.
AVOID placing the receiver in excessively dusty environ-
ments.
AVOID the use of chemical agents such as benzine or al-
cohol when cleaning, as they damage the receiver surfaces.
For U.S.A. only (FCC information)
CAUTION: Changes or modifications to this receiver, not
expressly approved by Icom Inc., could void your authority to operate
this receiver under FCC regulations.
Class B digital device users
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For Canada only
Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any in-
terference, including interference that may cause undesired opera-
tion of the device.
Microsoft®and Windows®are registered trademarks of Microsoft Corporation in
the U.S.A and other countries. Screen shots produced with permission from
Microsoft Corporation. All other products or brands are registered trademarks
or trademarks of their respective holders.
IC-PCR10003.qxd03.1.62:41PMページii
iii
SYSTEM REQUIREMENTS
• An RS-232C serial port (38400 bps or faster)
• Microsoft®Windows®98/98SE/Me/2000/XP
• At least 10 MB of hard disk space
• 640 ✕480 pixel display (800 ✕600 pixel display recommended)
TABLE OF CONTENTS
IMPORTANT ……………………………………………………………i
EXPLICIT DEFINITIONS ………………………………………………i
FEATURES ………………………………………………………………i
PRECAUTION …………………………………………………………ii
SYSTEM REQUIREMENTS …………………………………………iii
TABLE OF CONTENTS ………………………………………………iii
1 INSTALLATION ……………………………………………………1–7
■Hardware installation ………………………………………………1
■Antenna installation ………………………………………………2
■Grounding …………………………………………………………2
■AF output level selection …………………………………………3
■TNC connection ……………………………………………………4
■Software installation ………………………………………………5
■Uninstallation ………………………………………………………6
■Starting the IC-PCR1000 …………………………………………7
■Serial port setting …………………………………………………7
2 PANEL DESCRIPTION …………………………………………8–12
■Component screen…………………………………………………8
■Radio screen………………………………………………………12
■Communications receiver screen ………………………………12
3 SPECIFICATIONS………………………………………………13–14
4 SUPPLIED ACCESORIES AND OPTIONS ……………………15
■Supplied accesories………………………………………………15
■Options ……………………………………………………………15
IC-PCR10003.qxd03.1.62:41PMページiii
INSTALLATION 1
1
■Hardware installation
Refer to the diagram below for connections.
COMMUNICATIONS RECEIVER
iC- pcr1000
Remove the protective
sheet and attach to
a specified place.
Ground
to an AC adapter
to an
RS-232C port
Personal computer
to an
USB port
USB serial adapter cable
* When using the USB serial adapter cable, USB serial port can be used.
It is necessary to USB driver installation. The driver is supplied with the USB
serial adapter cable.
IC-PCR10003.qxd03.1.62:41PMページ1
1INSTALLATION
2
■Antenna installation
Antennas play a very important role in receiver operation.
Connecting a poor quality antenna to the IC-PCR1000 will re-
sult in less than optimum performance.
Select antenna(s), such as a well-matched 50 Ωantenna and
feedline. 1.5:1 of Voltage Standing Wave Ratio (VSWR) is
recommended for a desired band. Of course, the antenna line
should be a coaxial cable.
CAUTION: Protect your receiver from lightning by
using a lightning arrestor.
NOTE: The supplied antenna is a simple plain antenna which
may not obtain indicated specifications. To obtain maximum
performance from the IC-PCR1000, you must purchase an
external wide band antenna such as an optional Icom
AH-7000 (25–1300 MHz), etc.
Contact your nearest Icom Dealer or Service Center for re-
garding optimum antenna locations.
The antenna connector type is BNC, so an adapter may
be necessary to connect an optional antenna.
■Grounding
RWARNING: NEVER use a gas pipe or electrical
conduit pipe for grounding.
To prevent accidents involving electricity and interference
from computers, ground the receiver through the GROUND
terminal on the rear panel.
For best results, connect a heavy gauge cable to a water pipe
or long, earth-sunk copper rod. Make the distance between
the [GND] terminal and ground as short as possible.
COMMUNICATIONS RECEIVER
iC- pcr1000
IC-PCR10003.qxd03.1.62:41PMページ2
1
INSTALLATION
3
■AF output level selection
The received audio can be input into your computer via the
sound card.
Before inputting the received audio into the [LINE IN] con-
nector (connector name depends on your sound card), the
output level of the [EXT-SP] must be set properly. Perform as
follows:
qRemove the 8 screws from the cover as shown below.
Open the cover.
wSelect the output level as shown below.
- “SPEAKER”for internal speaker.
- “PHONES”for PC sound card or headphones.
eReplace the 8 screws and cover.
rConnect an appropriate cable between IC-PCR1000 and
PC.
- Plug for [EXT-SP] is supplied with the receiver.
SPEAKER
PHONES
COMMUNICATIONSRECEIVER
iC-pcr1000
IC-PCR1000
[EXT-SP]
to [LINE IN]
(depends on
your sound card)
IC-PCR10003.qxd03.1.62:41PMページ3
1INSTALLATION
4
■TNC connection
The IC-PCR1000 can receive 9600 bps packet communica-
tion (AFSK). Connect the TNC (Terminal Node Controller) as
follows.
COMMUNICATIONSRECEIVER
iC-pcr1000
TNC Personal computer
IC-PCR1000
to [PACKET]
IC-PCR10003.qxd03.1.62:41PMページ4
1
INSTALLATION
5
■Software installation
When installing into a Windows XP or Windows 2000 envi-
ronment, log on as the administrator.
qQuit all applications when windows is running.
wInsert the CD into the CD drive.
eSelect ‘Run’from the [Start] menu.
rType the setup program name with full path name, then
push the [Enter] key. (D:\SETUP.exe [Enter])
tClick [OK].
* The following screens show Windows XP.
•The “InstallShild®Wizard”starts preparing the installation.
yAfter the preparation, the following dialog is displayed.
Click [Next>].
Installing starts.
Click
Click
IC-PCR10003.qxd03.1.62:41PMページ5
1INSTALLATION
6
uAfter the installation is completed, click [Finish].
iEject the CD.
■Uninstallation
This section describes [IC-PCR1000] uninstallation.
DWindows XP
[Procedure]
qClick <Start> and select [Control Panel].
wClick [Add or Remove Programs] and select [ICOM IC-
PCR1000] and click <Change/Remove>.
e[IC-PCR1000] Uninstall Wizard starts automatically.
rClick <Uninstall> and follow the prompts.
DWindows 98/98SE/Me/2000
[Procedure]
qClick <Start> and select [Control Panel] from the [Settings]
menu.
wDouble-click [Add or Remove Programs] and select [ICOM
IC-PCR1000] and click <Change/Remove...>.
eFollow the prompts.
Click
IC-PCR10003.qxd03.1.62:41PMページ6
Altri manuali per IC-PCR1000
2
Indice
Altri manuali Icom Ricevitore
Icom
Icom IC-R9000L Manuale utente
Icom
Icom IC-R9500 Manuale utente
Icom
Icom IC-R7000 Manuale utente
Icom
Icom COMMUNICATIONS RECEIVER IC-R3 Manuale utente
Icom
Icom IC-R1 Manuale utente
Icom
Icom MXA-5000 Manuale utente
Icom
Icom IC-RX7 Manuale utente
Icom
Icom IC-RX7 Istruzioni per l'installazione e il funzionamento
Icom
Icom IC-R5 Manuale utente
Icom
Icom IC-R72 Manuale utente
Icom
Icom IC-R20 Manuale utente
Icom
Icom IC-A25N Guida all'installazione
Icom
Icom IC-751A Manuale utente
Icom
Icom IC-R1500 Manuale utente
Icom
Icom iR8600 Manuale utente
Icom
Icom IP501M Manuale utente
Icom
Icom IC-R1 Manuale utente
Icom
Icom IP501H Manuale utente
Icom
Icom IC-R6 Manuale utente
Icom
Icom IC-R9000L Manuale utente
