Icom IF3200DEX series Manuale utente

OPERATING INSTRUCTIONS

iF3200DEX

series

5 SPEAKER MICROPHONE

4 NXDN™OPERATION

3 BASIC OPERATION

2 PANEL DESCRIPTION

1 ACCESSORIES

INTRODUCTION

VHF DIGITAL/ANALOG TRANSCEIVERS

iF4200DEX

series

UHF DIGITAL/ANALOG TRANSCEIVERS

(Limited functions only)

INTRODUCTION

FOREWORD

Thank you for choosing this Icom product.

The IDAS™NXDN™system operation is built into your

transceiver.

IMPORTANT

FIRST, CAREFULLY READ INSTRUCTIONS

qPRECAUTIONS and wINSTRUCTIONS that are

provided with the transceiver.

SAVE THIS OPERATING GUIDE— This op-

erating guide contains additional important operating

instructions for the IC-F3201DEX, IC-F3202DEX and

IC-F3203DEX v h f digital/a n a l o g t r a n s c e i v e r s and

the IC-F4201DEX, IC-F4202DEX and IC-F4203DEX

u h f digital/a n a l o g t r a n s c e i v e r s .

NOTE

To use in explosive environments, read the “SAFETY

MANUAL” leaﬂet that comes with the transceiver.

Icom, Icom Inc. and the Icom logo are registered trademarks

of Icom Incorporated (Japan) in Japan, the United States,

the United Kingdom, Germany, France, Spain, Russia and/

or other countries.

IDAS is trademark of Icom Incorporated (Japan).

NXDN is a trademark of Icom Incorporated and Kenwood

Corporation.

All other products or brands are registered trademarks or

trademarks of their respective holders.

1-1

Section 1ACCESSORIES

Supplied accessories..............................................................1-2

Attaching accessories ............................................................1-3

Flexible antennaD......................................................................1-3

Battery packD............................................................................1-3

Belt clipD....................................................................................1-4

Connector coverD......................................................................1-4

1ACCESSORIES

1-2

Supplied accessories

The following accessories are supplied.

Battery pack*

Belt clip* Connector cover

(with screw)

Battery charger* Power adapter*

* Not supplied, or the shape is different, depending on the transceiver’s version.

Flexible antenna

(This illustration is for the VHF type.)

1ACCESSORIES

1-3

Attaching accessories

Flexible antennaD

Connect the supplied ﬂexible antenna to the antenna

connector.

CAUTION:

• NEVER carry the transceiver by holding only the

antenna.

• DO NOT connect any antenna other than those

listed in the basic instructions.

• Transmitting without an antenna will damage the

transceiver.

Battery packD

To attach the battery pack:

Slide the battery pack on the back of the transceiver in the

direction of the arrow (q)

until the battery release button

makes a ‘click’ sound.

To remove the battery pack:

Slide

the battery release button in the direction of the

arrow (w), as shown to the right. The battery pack is

then released, and you can remove it.

NEVER remove or attach the battery pack when the

transceiver is wet or soiled. This may result in water

or dust getting into the transceiver/battery pack and

may damage them.

NOTE: Keep the battery pack terminals clean. It’s a

good idea to occasionally clean them.

Battery release

button

1ACCESSORIES

1-4

Belt clipD

Before attaching or detaching the belt clip, remove the

battery pack if it is attached.

To attach the belt clip:

Slide the belt clip in the direction of the arrow until it➥

locks and makes a ‘click’ sound.

To detach the belt clip:

Lift the tab up (➥q), and slide the belt clip in the direc-

tion of the arrow (w).

Attaching accessories (Continued)

Connector coverD

To attach the connector cover:

Place the connector cover over the multi-connector.q

(q)

Tighten the screw. (ww)

To detach the connector cover:

Remove the screw using a Phillips screwdriver. (qe)

Detach the connector cover to connect optionalw

equipment. (r)

Belt clip

Ta b

CAUTION:

Attach the connector cover when the optional ac-

cessory is not used. Otherwise, the terminals of the

multi-connector may be shorted, and this could dam-

age the transceiver.

2-1

Section 2PANEL DESCRIPTION

Front, top and side panels ......................................................2-2

Status indicator .......................................................................2-3

Programmable function keys .................................................2-5

2PANEL DESCRIPTION

2-2

Front, top and side panels

qROTARY SELECTOR

Rotate to select the preprogrammed memory chan-

nels or scan lists, depending on the presetting.

wVOLUME CONTROL [VOL]

Rotate to turn the power ON or OFF, and adjust the

audio level.

eSTATUS INDICATOR (p. 2-3)

Lights red while transmitting.➥

Lights green while receiving a signal, or when the➥

squelch is open.

Lights/blinks orange when a matched 2/5-Tone➥

code is received, depending on the presetting.

rMULTI CONNECTOR

Connect an optional accessory.

CAUTION:

Attach the connector cover

when an optional accessory

is not used. Otherwise, the

terminals of the multi-con-

nector may be shorted, and

this could damage the trans-

ceiver.

tPTT SWITCH [PTT]

Hold down to transmit, release to receive.

yLOWER KEY [Lower]

uUPPER KEY [Upper]

A desired functions can be preset. (p. 2-4)

iEMERGENCY KEY [Emer]

A desired functions can be preset. (p. 2-4)

oANTENNA CONNECTOR

Connect the antenna.

Connector

cover

Microphone

Speaker

wVOLUME

CONTROL

eSTATUS INDICATOR

yLOWER KEY

uUPPER KEY

qROTARY

SELECTOR

oANTENNA

CONNECTOR

rMULTI

CONNECTOR

tPTT SWITCH

iEMERGENCY

KEY

2PANEL DESCRIPTION

2-3

Status indicator

• TX:

Lights Red while transmitting.

• RX busy:

On an analog channel, lights Green when the noise

squelch opens. On a digital or mixed channel, lights

Green while detecting a frame synchronization.

• Call LED:

Turns ON or blinks* when receiving a matched 2/5-

Tone, or a Call Alert.

*Depending on the presetting.

• Fast or Slow scan:

Blinks when scanning for a channel to search for a

signal.

• Low Battery 1:

You should charge the battery soon. (blinks slowly)

• Low Battery 2:

You must charge the battery. (blinks fast)

• TX low Battery 1:

Low Battery was detected in the TX mode.

• TX low Battery 2:

Very Low Battery was detected

in the

TX mode.

• Channel Error:

Continuously blinks when a non-programmed chan-

nel is selected.

• Power ON:

Blinks at transceiver startup.

O O

G G

G G G G

The status indicator indicates the various parameters

of the transceiver as described below.

(Reference: R is Red, G is Green, O is Orange)

R O R O R O R O R O R O R O R O

R O GRO G

R R

R R R R

(When turns ON)

(When blinks)

2PANEL DESCRIPTION

2-4

Programmable function keys

The following functions can be assigned to the [Upper],

[Lower] and [Emer] programmable function keys.

LOWER KEY

UPPER KEY

EMERGENCY

KEY

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Ricetrasmettitore popolari di altre marche

Yaesu

Yaesu FT-7B Manuale utente

Kenwood

Kenwood ProTalk TK-3201 Manuale utente

Texas Instruments

Texas Instruments TLK10232 Manuale utente

Mizuho

Mizuho MX-2 Guida del prodotto

Kenwood

Kenwood TK-3180 Manuale operativo e di manutenzione

Blitz

Blitz MJ-398U Manuale utente

Utilicom

Utilicom LongRanger 2050 Manuale utente

Standart

Standart HX290UKA Manuale utente

Altronix

Altronix Pace1PTM Manuale utente

Kirisun

Kirisun PT2208 Manuale utente

ELECRAFT

ELECRAFT KX2 Manuale utente

Zodiac

Zodiac K3 Manuale utente

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuale utente

Kenwood

Kenwood TK-2217 Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Kenwood

Kenwood TS-590SG Manuale utente

Midland

Midland G8E-BT Manuale

ComNav

ComNav Mariner X2 Manuale utente

Icom iF3200DEX series Manuale utente

Manuali Ricetrasmettitore popolari di altre marche