IFM Electronic OGP Manuale utente

Operating instructions

Retro-reflective sensor with IO-Link

OGP

80282424 / 00 01 / 2019

Contents

1 Preliminary note��3

1�1 Symbols used ��3

2 Safety instructions ��3

3 Functions and features ��3

4 Installation��4

5 Electrical connection��4

5�1 PNP ��4

5�2 NPN ��4

6 Settings��5

6�1 Set via IO-Link ��5

6�1�1 Set sensitivity with prismatic reflector / reflective tape and object��5

6�1�2 Set maximum sensitivity ��6

7 Operation��6

8 Maintenance, repair, disposal��6

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of keys, buttons or indications

→Cross-reference

Information

Supplementary note�

Important note

Non-compliance may result in malfunction or interference�

2 Safety instructions

• Read this document before setting up the product and keep it during the entire

service life�

• The product must be suitable for the corresponding applications and

environmental conditions without any restrictions�

• Only use the product for its intended purpose (→ 3 Functions and features)�

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property may occur�

• The manufacturer assumes no liability or warranty for any consequences

caused by tampering with the product or incorrect use by the operator�

• Installation, electrical connection, set-up, operation and maintenance of the

product must be carried out by qualified personnel authorised by the machine

operator�

• Protect units and cables against damage�

3 Functions and features

In conjunction with a prismatic reflector or reflective tape the retro-reflective

sensor detects objects and materials without contact and indicates their presence

by a switching signal�

For the range see the type label�

4 Installation

►Fit the prismatic reflector or the reflective tape behind the object to be detected�

Align the retro-reflective sensor to it and secure it to a bracket�

> Maximum range only with accurate alignment�

5 Electrical connection

The unit must be connected by a qualified electrician�

►The national and international regulations for the installation of

electrical equipment must be adhered to�

►Ensure voltage supply to EN 50178�

►Disconnect power�

►Connect the unit as follows:

5.1 PNP











Pin 1 = L+ (10...30 V DC)

Pin 3 = L-

Pin 4 = load (PNP, 200 mA) / IO-Link

(Pin 2 = not connected)

5.2 NPN











Pin 1 = L+ (10...30 V DC)

Pin 3 = L-

Pin 4 = load (NPN, 200 mA) / IO-Link

(Pin 2 = not connected)

6 Settings

6.1 Set via IO-Link

This unit has an IO-Link communication interface which enables direct access to

process and diagnostic data� In addition it is possible to set the parameters of the

unit while it is in operation� Operation of the unit via the IO-Link interface requires

an IO-Link master�

With a PC, suitable IO-Link software and an IO-Link adapter cable communication

is possible while the system is not in operation�

The IODDs necessary for the configuration of the unit, detailed information about

process data structure, diagnostic information, parameter addresses and the

necessary information about the required IO-Link hardware and software can be

found at www�ifm�com�

6.1.1 Set sensitivity with prismatic reflector / reflective tape and object

►Start the LR DEVICE software�

► Align the retro-reflective sensor to the object (fig. 1).

►Select [Teach SP1 TP1] in the LR DEVICE software�

►Align the retro-reflective sensor to the prismatic reflector or reflective tape (fig�

2).

►Select [Teach SP1 TP2] in the LR DEVICE software�

Either the object can be set first and then the prismatic reflector / reflective

tape, or the other way around�

Fig� 1: Fig� 2:

TP1 TP2

TP1: teach point 1 TP2: teach point 2

6.1.2 Set maximum sensitivity

►Start the LR DEVICE software�

►Align the sensor so that no light is reflected�

►Select [Teach SP1 TP1] in the LR DEVICE software�

►Select [Teach SP1 TP2] in the LR DEVICE software�

7 Operation

►Check whether the unit operates correctly�

> The green LED is on when the unit is ready for operation�

> The yellow LED is on when the switching output is switched�

8 Maintenance, repair, disposal

►Keep the lens of the sensor free from soiling�

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic parts�

►After use dispose of the unit in an environmentally friendly way in accordance

with the applicable national regulations�

Faulty sensors must only be repaired by the manufacturer�

Technical data and further information at www�ifm�com

Indice

Altri manuali IFM Electronic Accessori

IFM Electronic

IFM Electronic Efector 200 OL Series Manuale utente

IFM Electronic

IFM Electronic efector 200 OG laser Manuale utente

IFM Electronic

IFM Electronic efector 410 JN2300 Guida all'applicazione

IFM Electronic

IFM Electronic LR3000 Manuale utente

IFM Electronic

IFM Electronic Efector 200 Manuale utente

IFM Electronic

IFM Electronic efector200 OJ51 Series Manuale utente

IFM Electronic

IFM Electronic efector160 LI51 Manuale utente

IFM Electronic

IFM Electronic Efectorsod PE70 Series Manuale utente

IFM Electronic

IFM Electronic Efector500 PF2058 Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

IFM Electronic

IFM Electronic O3M151 Manuale del proprietario

IFM Electronic

IFM Electronic LR2750 Manuale utente

IFM Electronic

IFM Electronic efector200 O7H2 Series Manuale utente

IFM Electronic

IFM Electronic O1D155 Manuale utente

IFM Electronic

IFM Electronic VSA003 Manuale utente

IFM Electronic

IFM Electronic Efector160 LK3 Manuale utente

IFM Electronic

IFM Electronic LR7300 Manuale utente

IFM Electronic

IFM Electronic efector230 UGA Manuale utente

IFM Electronic

IFM Electronic efector 250 Manuale utente

IFM Electronic

IFM Electronic PI7093 Manuale utente

IFM Electronic

IFM Electronic PA32xx Series Manuale utente

IFM Electronic

IFM Electronic efector180 IX50 Manuale utente

IFM Electronic

IFM Electronic efector 300 SU8000 Manuale utente

IFM Electronic

IFM Electronic Efector 200 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuale utente