IHP H0776 Manuale utente

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INSTALLATION INSTRUCTIONS FOR FIREBOX LINER KITS

FOR USE WITH FIREPLACE MODELS LISTED BELOW

SHIPPING AND PACKING LIST

Package 1 of 2 contains:

1 - Left Side Panel (Kits: H0775, H0776, H0777, H0779, H0781, H0912,

H2067, H2068, H2069, H2071, H2073, H3207, H4683, H4684,

H4685, H4686).

1 - Right Side Panel (Kits: H0775, H0776, H0777, H0778, H0779,

H0780, H0912, H2066, H2067, H2068, H2069, H2070, H2071,

H2072, H2073, H3207, H4683, H4684, H4685, H4686).

1 - Rear Panel (Kits: H0775, H0776, H0777, H0780, H0781, H0912,

H2067, H2068, H2069, H2071, H2073, H4683, H4684, H4685,

H4686).

1 - Bafﬂe (Kits: H0775, H0776, H0777, H2067, H2069, H2071, H2073).

1 - Template (Kit: H0779)

1 - Installation Instructions.

Package 2 of 2 (for Kits H2023, H2024, H2074 & H2075 only) contains:

1 - Rear Log (H1381).

FIREBOX LINER KITS

750160M

Rev. N 03/2016

Figure 1 (40" Front Open)

Left Side

Firebox Wall

Front Lintel

Lintel Securing

Screw (Both Sides)

Rear Lintel

Right Side

Firebox Wall

Grate Assembly Log Spacer Ceramic Fiber Floor

(Some Older Models)

Clay Tan Interior Shown

(Some Older Models)

MODELS

This Firebox Liner Kit (see Figure 1)is for use only in the following

models of ﬁreplaces:

Color: Boston Buff

Catalog # Model # Where Used *

H0775 EBLK-35 EDV3530

H0776 EBLK-40 Altair™ 40, DRT4040, EDV4035

H0777 EBLK-45 Altair 45, DRT4045, EDV4540

H0778 EBLK-PF Libra™40PF, DRT40PF,

MHD40PF, EDVPF, EBVPF

H0779 EBLK-ST Libra40ST, DRT40ST,

MHD40ST, Marin™ 40ST, BRT40ST,

EDVST, EBVST

H0780 EBLK-CL Libra 40CL, DRT40CL, EDVCL

H0781 EBLK-CR Libra40CR, DRT40CR, EDVCR

H0912 MBLK-33T MPDT3328/MDT3328/DT400

H8596 BLKC-MP40 D600/DR600

H8614 BLKC-MP33R MPDR3328/MDR3328/DR400

H2023 MBLK-40L MPD4035

H2024 MBLK-45L MPD4540

H3207 MBL-35ST Eros™ 35ST/PF, DRT35ST/PF,

Rochester™ ST/PF, MPB35ST,

MPD35ST

H4683 MBLK-33B MPB-33

H4684 MBLK-35B MPB-35

H4685 MBLK-40B MPB-40

H4686 MBLK-45B MPB-45

Color: Black

Catalog # Model # Where Used

H2067 BBLK-4R(R) DR-400, MDR3328

H2068 BBLK-5T(R) DT-500

H2069 BBLK-5R(R) D500, DR500, MPD3530-B, BDM35

H2071 BBLK-6R(R) D600/DR600

H2073 BBLK-8R(R) D800/DR800

H2086 BBLK-45(R) MPD4540-B

* The accessories listed here will ﬁt Lennox Hearth Products (LHP) ﬁre-

place models that are shown above in a smaller font.

HEARTH PRODUCTS

KITS AND ACCESSORIES

fire-parts.com

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 4 (40" Front Open)

Baffle

Figure 3 (40" Front Open)

Left Side Panel Right Side Panel

Front Lintel Screws (5 Places)

INSTALLATION INSTRUCTIONS -

LHP FIREPLACE MODELS - MPD, MPB & SUPERIOR D-SERIES

(For Kits: H0912, H2023, H2024, H2067, H2068, H2069, H2071,

H2073, H2074, H2075, H4683, H4684, H4685 & H4686)

Step 1. Follow the procedure "Turning Off Gas To Unit", located on the

Lighting Instructions pullout labels in the control compartment of the

unit and in the Installation Instructions provided with the appliance.

Step 2. Refer to the appliance Installation and Operation Instructions

and gain access to and remove the front glass enclosure panel.

Step 3. Carefully remove the log set from the ﬁrebox.

Step 4. Remove the existing rear lintel (if applicable) as shown in

Figure 1 by removing the two screws. Use the screws to plug the two

screw holes.

Figure 2 (40" Front Open)

Rear Panel

INSTALLATION INSTRUCTIONS - FRONT OPEN FIREPLACES

(For Kits: H0775, H0776 & H0777)

Step 1. Follow the procedure "Turning Off Gas To Unit", located on the

Lighting Instructions pullout labels in the control compartment of the

unit and in the Installation Instructions provided with the appliance.

Step 2. Refer to the appliance Installation and Operation Instructions

and gain access to and remove the front glass enclosure panel.

Step 3. Carefully remove the log set from the ﬁrebox.

Step 4. Remove the existing rear lintel as shown in Figure 1 by removing

the two screws. Use the screws to plug the two screw holes.

Step 5. Remove and discard the log spacer as shown in Figure 1 by

removing the two screws.

Step 6. Insert the rear panel into ﬁrebox and position against the rear

wall of the ﬁrebox (see Figure 2).

Step 7. Carefully slide the left side panel into ﬁrebox between the left

side ﬁrebox wall and the front lintel (see Figure 3).

NOTE: For some older models, the front lintel needs to be removed by

unscrewing the ﬁve (5) attaching screws, and requires the ﬁeld trim-

ming of 3/4" on each end, in order for the panels to ﬁt. After trimming,

reinstall the front lintel using the ﬁve (5) existing screws.

NOTE: Previous EDV models with clay-tan painted interiors were shipped

from the factory with ceramic ﬁber brick pattern ﬂoor ﬁnish treatments.

These ﬂoor panels will raise the side panels of the newest brickaded

panel liner kits, causing a misalignment of the brick pattern relation to

the rear panel. To correct, either remove the ﬂoor panels and replace

with decorative volcanic stone to taste (Model FDVS - 80L42) or using

a box knife, cut 1/2" off the bottom edge of each side panel.

Step 8. Repeat Step 7 for the right side panel.

Step 9. Place the ceramic bafﬂe into the ﬁrebox as shown in Figure 4.

Step 10. Carefully replace the log set. Refer to the Installation and

Operation Instructions and the detailed Log Set Placement Supplement,

included with the appliance.

fire-parts.com

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 5 (PF Models)

Figure 6

Cut-Out In Panel For Rear Vent Access

Right Side Panel

(Top Vented Shown)

Front Lintel Screws (5 Places)

Ceramic Fiber Floor (Some Older Models)

Step 4. EBLK-ST (Catalog # H0779)

A. For Top Vented application.

1. Slide the provided left and right side panels into the unit as

shown in Figure 9.

NOTE: For some older models, the front two (2) lintels need to be re-

moved by unscrewing the four (4) attaching screws on each lintel, and

requires the ﬁeld trimming of 3/4" on the panel end of the lintel, in order

for the panels to ﬁt. After trimming, reinstall the front lintels using the

four (4) existing screws.

Step 2. Refer to the appliance Care & Operations/Installation Instruc-

tions and gain access to and remove the front glass enclosure panel.

Step 3. EBLK-PF (Catalog # H0778)

A. For Top Vented application.

1. Slide the provided side panel into the unit as shown

in Figure 5.

NOTE: For some older models, the front two (2) lintels need to be re-

moved by unscrewing the ﬁve (5) attaching screws on each lintel, and

requires the ﬁeld trimming of 3/4" on the panel end of the lintel, in order

for the panels to ﬁt. After trimming, reinstall the front lintels using the

ﬁve (5) existing screws.

B. For Rear Vented application.

1. To allow for rear vent access, remove the U-Shaped cut-out

from the back of the provided panel. Using a standard utility

knife, cut through panel material along the U-shaped line

and then discard the cut out piece. See Figure 6.

2. Slide the panel into the unit as shown in Figure 5. (See Note

Above).

Step 5. Insert the rear panel into ﬁrebox and position against the rear

wall of the ﬁrebox (refer to Figure 2).

NOTE: (for Kits H0915, H2024 & H2075 only): Use a utility knife or

blade to remove excess material, using perforated line on the back of

the panel as a guide.

Step 6. Carefully slide the left side panel into ﬁrebox between the left

side ﬁrebox wall and the front lintel (refer to Figure 3).

NOTE: For some older models, the front lintel needs to be removed by

unscrewing the attaching screws, and requires the ﬁeld trimming of 1/2"

on each end, in order for the panels to ﬁt. After trimming, reinstall the

front lintel using the existing screws.

Step 6a. (For Kits: H2067, H2069, H2071, H2073, H2074 & H2075)

Install provided lintel using the existing screws.

Step 7. Repeat Step 6 for the right side panel.

Step 8. Place the ceramic bafﬂe into the ﬁrebox (if applicable) as shown

in Figure 4.

Step 9. (For Kits: H2023, H2024, H2074 & H2075 only) Replace the

rear log (39-7 molded on back) with the log provided (138 molded on

back). Please save the original log for future burning without ceramic

panel (if desired).

Step 10. Carefully replace the log set. Refer to the Installation and

Operation Instructions and the detailed Log Set Placement Supplement,

included with the appliance.

INSTALLATION INSTRUCTIONS - MULTI OPEN FIREPLACES

(For Kits: H0778, H0779, H0780, H0781 & H3207)

Step 1. Follow the procedure "Turning Off Gas To Unit", located on the

Lighting Instructions pullout labels in the control compartment of the

unit and in the Installation Instructions provided with the appliance.

fire-parts.com

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 9

Step 5. EBLK-CL (Catalog # H0780), EBLK-CR (Catalog # H0781)

A. For Top Vented application.

1. Slide the provided rear panel into the unit as shown in

Figure 10.

NOTE: For some older models, the side and front lintels need to be

removed by unscrewing the two (2) and ﬁve (5) attaching screws

respectively, and requires the ﬁeld trimming of 3/4" on the panel end

of the lintels, in order for the panels to ﬁt. After trimming, reinstall

the side and front lintels using the existing screws.

2. Slide the provided side panel into the unit as shown in

Figure 11. (See Note Above).

Figure 7 - B-Vent ST Models

Figure 8 - B-Vent ST Models

Right Side Panel

(Top Vented Shown)

Left Side

Panel

Front Lintel Screws

(4 Places)

C. For Rear Vented application.

1. To allow for rear vent access, remove the U-Shaped cut-out

from the back of one of the provided panels. Using a standard

utility knife, cut through panel material along the U-shaped line

and discard the cut out piece. Refer to Figure 6. (See Note

at the bottom of Page 3).

2. Slide the panel with the U-shaped cut out removed into the

unit (on the vented side of the unit) as shown in Figure 9.

3. Slide the other provided panel into the unit, as shown in

Figure 9. (See Note at the bottom of Page 3).

Template

Cut along

dashed lined

B. For "B" Vent application.

1. To allow for relief opening access, place template on back side of

panel (see Figure 7)using a standard utility knife, cut through panel

material along the U-shaped line and discard the cut out piece (see

Figure 8).

2. Remove the two (2) front lintels by unscrewing the four (4) at-

taching screws on each lintel.

3. Slide the panel with the U-shaped cut-out removed into the unit

(on the relief opening of the unit) as shown in Figure 9.

4. Slide the other provided panel into the unit as shown in Figure 9.

5. Reinstall the front lintels using the existing screws.

fire-parts.com

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 10 (CR/CL Models)

Side Panel (Top Vented Shown) Rear Panel

Figure 11 (CR/CL Models)

Rear Panel

Front Lintel Screws

(5 Places)

Side Lintel Screws

(2 Places)

B. For Rear Vented application.

1. Slide the provided rear panel into the unit as shown in

Figure 10. (See Note Above).

2. To allow for rear vent access, remove the U-Shaped cut-out

from the back of one of the provided panels. Using a standard

utility knife, cut through panel material along the U-shaped line

and discard the cut out piece. Refer to Figure 6.

NOTE: Make sure to remove the appropriate cut out corresponding to

your unit model number, CL (corner left), CR (corner right).

3. Slide the side panel with the U-shaped cut out removed into

the unit (on the vented side of the unit).

NOTE: For some older models, the side and front lintels need to be

removed by unscrewing the two (2) and ﬁve (5) attaching screws

respectively, and requires the ﬁeld trimming of 3/4" on the panel end

of the lintels, in order for the panels to ﬁt. After trimming, reinstall

the side and front lintels using the existing screws.

fire-parts.com

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

P/N 750160M Rev. N 03/2016

IHP reserves the right to make changes at any time, without notice, in design, materials,

speciﬁcations, and prices, and also to discontinue colors, styles, and products. Consult your

local distributor for ﬁreplace code information.

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

fire-parts.com

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Accessori per caminetti popolari di altre marche

Valor

Valor L2 1700K Manuale utente

Exodraft

Exodraft Xzense Manuale utente

Whalen

Whalen Ruso MNFP62BF23-6 Manuale utente

Lopi

Lopi Hearthview 864 Manuale utente

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manuale utente

EdilKamin

EdilKamin SERBATOIO 250 Guida rapida

Bronpi

Bronpi KIT-1 Manuale utente

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manuale utente

Travis Industries

Travis Industries 33 DVI Manuale utente

Superior

Superior ASD3628-TI Manuale utente

pleasant hearth

pleasant hearth OFP28WG Manuale utente

Firegear

Firegear FG-H-2110SS Manuale utente

Nibe

Nibe Contura C i31 Manuale utente

kozy heat

kozy heat KZK-052 Manuale utente

SimpliFire

SimpliFire SF-WM36 Manuale utente

Bluegrass Living

Bluegrass Living BC18NR Guida rapida

pleasant hearth

pleasant hearth IRIS SCROLL Manuale utente

Cooke

Cooke Glass Wind Guard Manuale utente