Ikelite 6171.11 Manuale utente
ProductRegistration
Please register your product at ikelite.com within 15 days of purchase.
Our product registration database is the best way for us to contact you
in the event of a product update.
Underwater TTLHousingforPanasonic LumixLX100,
LeicaD-Lux(Typ109)
Product Number 6171.11
2
AboutthisProduct
Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product. Please visit ikelite.com to register your product to
receive information on any updates, notices, or recalls pertaining to
your equipment.
IncludedintheBox
• Housing
• O-ring # 0110
• Waterproof bulkhead cap # 9104.5
• Vinyl port cover # 0200.08
• Gear ring # 9299.11
• Control + push button tip assortment # 9249.3
• 1/8” hex key # 0945.18
• Silicone lubricant # 0184.1
3
ImportantNotices
»To prevent salt build-up and sticking controls, submerge the
empty housing in clean, freshwater. Operate the controls
several times each while underwater to ush out any residue.
»Never leave a housing in a rinse tank, even if it is the only
system in the tank. Most catastrophic oods happen when the
user walks away from a housing while it is in the rinse tank.
»Do not use alcohol, cleaning agents, spray lubricants, Rain-X,
or other solvents on the housing or lens port. Use of an
incompatible chemical compound can damage the plastic and
o-rings, and may result in leaking.
AccessoryPort
»Do not remove the Accessory Port Plug unless you are
installing a compatible accessory.
Your housing features one spare Accessory Port which may be used
for attachment of factory optional or aftermarket housing accessories.
The Accessory Port is 1/2-20 threaded.
Visit ikelite.com for information on optional accessories.
4
Contents
Product Registration 1
About this Product 2
Included in the Box 2
Important Notices 3
Accessory Port 3
Getting to Know Your Housing 6
Setting Up Your Camera 8
Pre-Installation Checklist 8
Setting Up Your Housing 8
Opening the Housing 8
Inserting the Camera 9
Attaching the Hotshoe 10
Closing the Housing 11
Setting Up An External Strobe 11
Strobe Compatibility 12
Attaching a Sync Cord 12
Taking your Housing in the Water 13
Final Check 13
Entering the Water 14
In the Water 14
Maintenance 15
Post-Dive 15
Travel and Storage 15
Troubleshooting 16
Service and Repairs 18
Limited Warranty 18
Contact Us 19
5
6
GettingtoKnow YourHousing
Shutter
Filter
Zoom
Shutter speed
Bulkhead
Lidsnap Lens Port
Tray mounts
Aperture
7
MENU
Fn3 Fn2
AE/FE
LOCK
Fn1 DISP
14
WB
ISO
MENU
Fn3 Fn2
AE/FE
LOCK
Fn1 DISP
14
WB
ISO
Accessory
port
Lid hook
O-ring
Camera mount
plate
Lanyard
Exposure
compensation
Rear * dial
ON/OFF
MENU/SET
White Balance
Playback
Drive Mode
Fn1/Delete
AF Mode
8
SettingUpYour Camera
Pre-Installation Checklist
1. Insert a fully charged camera battery.
2. Insert a properly formatted memory card.
3. In the REC menu, set Red-Eye Removal to OFF.
4. In the C menu, set Shutter AF to ON.
5. In the C menu, set Half Press Release to OFF.
6. In the C menu, set Quick AF to ON.
7. In the C menu, set Eye Sensor AF to OFF.
8. In the C menu, set AF Assist Lamp to OFF.
9. In the C menu, set Focus/Release Priority to FOCUS.
SettingUpYour Housing
Opening the Housing
1. Push the lid snap lock forward and start to lift the curved end away
from the housing.
9
2. Lid snaps are designed to provide enough force to compress the
o-ring for a proper seal. Keep rm pressure against the lid snap
while lifting it away.
Lid Snap Lock
3. Repeat with remaining lid snaps.
4. Remove the housing back.
Inserting the Camera
1. Remove any lanyard or neck strap which may be attached to the
camera.
2. Orient the Gear Ring with the foam strips on top and bottom and
the white dot at the top center. Attach the Gear Ring to the camera
by gently pressing it onto the camera’s Aperture Ring. The front of
the Gear Ring should be ush with the front of the Aperture Ring.
Lumix
L
3. Remove the Camera Mounting Plate from the housing.
10
4. Line up the mounting screw with the camera’s tripod socket. Use a
at head screwdriver to tighten the mounting plate to the camera.
Mounting screw
1/4-20 tripod
mount
Camera tripod
socket
5. Pull out on the housing’s ON/OFF, Shutter Speed, and Exposure
Compensation knobs to move them out of the way.
6. Insert the Mounting Plate into the corresponding slot on the inside
bottom of the housing. Rotate the front aperture knob slightly to
assist Gear Ring engagement with housing gear. Slowly push the
camera all of the way forward until the back of the Mounting Plate is
ush with the back of the housing mount.
7. Check the Gear Ring. If it has slipped backwards slightly, gently
push the top forward to engage with the gearing in the front of the
housing.
8. Orient the On/OFF control so that the legs of the “U” are on either
side of the camera lever.
»The camera’s Aperture Ring does not rotate 360º. Do not force
the control to rotate past its natural stop. Forced over-rotation
may damage the housing’s gearing.
FRONT
Altri manuali per 6171.11
1
Indice
Altri manuali Ikelite Accessori per fotocamere
Ikelite
Ikelite 6047 Manuale del proprietario
Ikelite
Ikelite Olympus D-230 Manuale operativo e di manutenzione
Ikelite
Ikelite 6111.5 Manuale utente
Ikelite
Ikelite SLR-DC Housing Manuale utente
Ikelite
Ikelite #6184.80 Manuale utente
Ikelite
Ikelite 75301 Manuale utente
Ikelite
Ikelite IXUS65 Manuale utente
Ikelite
Ikelite Digital Housing Manuale del proprietario
Ikelite
Ikelite C-750 Manuale utente
Ikelite
Ikelite 6843.72 Manuale utente
Ikelite
Ikelite 6110.91 Manuale utente
Ikelite
Ikelite 6430 W-30 Manuale utente
Ikelite
Ikelite 71722 Manuale utente
Ikelite
Ikelite DSC-W50 Manuale utente
Ikelite
Ikelite Canon EOS 10D Manuale utente
Ikelite
Ikelite S95 Manuale del proprietario
Ikelite
Ikelite 6184.7 Manuale utente
Ikelite
Ikelite 200DLM Manuale utente
Ikelite
Ikelite 6870.70 Canon EOS 70D Manuale utente
Ikelite
Ikelite 6184.91 Manuale utente
