illunis CMV-50M Manuale utente
Operations Manual
7920 x 6004 Global Shutter CMOS
CMV-50
CMV-50 Operations Manual Copyright illunis, LLC 9/20/2019 Page 2
Revisions
CMV-50
Rev Date Modification
A4/5/2018 CMV-50 Original Document
B3/7/19 2019 Revisions
C5/10/19 Command Updates
D9/20/19 Command Updates—frame rate tables
Camera Communication Default Baud Rate is 115,200
CMV-50 Operations Manual Copyright illunis, LLC 9/20/2019 Page 3
Precautions
CMV-50
CMV-50 Precautions
Do not drop, damage, disassemble, immerse, repair or alter the
camera.
Applying incorrect power may damage the camera electronics.
The warranty is void if the camera is opened or modified in any
way.
Care must be taken in handling as not to create static dis-
charge that may permanently damage the device.
Camera Link is a DC based interface. The camera and capture
device must share the same electrical ground. Failure to do so
will damage the Camera Link interface chips and/or camera
and capture card.
The maximum Camera Link data rate is 85Mhz. This limits the
maximum pixel clock speed to 42.5Mhz, which is provided as
an overclock mode. Operation is guaranteed at 30Mhz pixel
clock and below.
PoCL cables are compatible with the CMV-50
camera. PoCL camera power is not supported.
Absolute Maximum Ratings
Input Voltage: 6 to 16V DC
Storage Temperature: -40C to +70C
Recommended Maximum Ratings
Input Voltage: 9 to 14V DC
Operating Temperature: 0C to +60C
Most illunis cameras operate beyond these temperature limits,
please call for details.
Recommended Operating Conditions
Input Voltage: 9-12V DC
Operating Temperature: 0C to 60
Relative humidity should not exceed 80% non-condensing.
Specifications subject to change without notice.
CMV-50 Operations Manual Copyright illunis, LLC 9/20/2019 Page 4
Contents
CMV-50
Table of Contents Page
Getting Started - Camera Link 5
Getting Started - USB3/GigE 21
Camera Overview 31
Hardware Overview 44
Serial Communication 48
Serial Commands 51
Pixel, Row and Column Defects 60
Hot Pixel Correction 61
CMV-50 Operations Manual Copyright illunis, LLC 9/20/2019 Page 5
Camera Power
6-12V DC Power to the Hirose 6 pin connector.
Mating Connector: Hirose HR10A-7P-6P
View from Camera Back
Capture Card
Any Base, Medium or Full Format Camera Link capture card
Such as: Teledyne Dalsa Xtium-CL MX4 OR-Y4CO-XMX00.
Imaging SDK
Available from your capture card supplier.
Camera Link Cables
One, two or four Camera Link cables (Mini HDR to SDR) must be
rated at 85Mhz or more (two cables for Medium or Full Format).
The following 5M cable configurations have been tested:
Standard MDR to HDR/SDR MVC-1-1-5-5M
Available from Components Express.
http://www.componentsexpress.com/Configurator.aspx?cnfi=1
Camera Communication Software
illunis Camera Serial Communication Software
Download at: http://illunis.com/illunis/downloads
Getting Started Camera Link
CMV-50
CMV-50 Operations Manual Copyright illunis, LLC 9/20/2019 Page 6
To start imaging with the CMV-50 CL:
Install the capture card and software per the capture card
manufacturers instructions.
Connect the CMV-50 Camera Link cables paying attention
to the base and medium connections
Getting Started Camera Link
CMV-50
Camera Link Medium mode setup
Blue cable = Base Mode Connection
Green cable = Medium/Full Connection
Camera Link
Communication: CLA
A
Cable Connections for Camera Link Medium/Full Mode
Operation.
Base Mode uses only CLA Base Connection
CMV-50 Operations Manual Copyright illunis, LLC 9/20/2019 Page 7
Getting Started Camera Link
CMV-50
Blue cable = Base Mode Connection Left
Green cable = Medium/Full Connection Left
Red cable = Base Mode Connection Right
Orange cable = Medium/Full Connection Right
Set trigger source to “CLA”
Capture card
for left 3960
pixels
Capture card
for right 3960
pixels
Camera Link
Communication: CLA
B
A
Cable Connections for Camera Link Dual Full Mode Operation
CMV-50 Operations Manual Copyright illunis, LLC 9/20/2019 Page 8
Installing the illunis Camera Serial Communication Software:
Download and install the illunis Camera Serial
Communication Software from
http://illunis.com/illunis/downloads
Background:
Per the CameraLink standard, all serial communication is via the .dll
clallserial.dll, which dynamically loads the serial communication .dll(s)
specific to the frame grabber being used. illunis installs clallserial .dll in
its application directory.
clallserial.dll examines the registry to see where the capture card
specific communication dll's have been installed. The naming
convention for the capture card specific communication dll's is
clser***.dll where *** is the manufacturer specific dll name. The files
MUST be in the form clser***.dll in order to be recognized. Some
capture card manufacturers will append something like clser***x64.dll
for the 64 bit version of the .dll. This file name must be changed to
clser***.dll in order to be recognized by clallserial.dll.
illunis camera
control app
clallserial.dll
clserxxx.dll clseryyy.dll clserzzz.dll
Getting Started Camera Link
CMV-50
CMV-50 Operations Manual Copyright illunis, LLC 9/20/2019 Page 9
The registry:
When clallserial.dll is loaded by the illunis serial communication application, it
looks at the Registry entry:
HKEY_LOCAL_MACHINE\SOFTWARE\Cameralink CLSERIALPATH.
The location pointed to by CLSERIALPATH is typically C:\Cameralink\Serial,
but could be any path that a capture card install might create. It is important to
note that the capture card communication dll(s), clser***.dll must be at this
path location. clallserial.dll should NOT be in this location.
If the capture card communication dll is spec 1.1 compliant, the user will find
this directory already created.
The illunis control app installs clallserial.dll for the appropriate operating
system in the application folder. Depending on the application version, some
documentation may be installed in the application folder as well.
If the registry entry above does not exist, create it as well as the directory
C:\CameraLink\Serial
In either case—copy and paste the clser***.dll files to the
C:\CameraLink\Serial folder.
Getting Started Camera Link
CMV-50
CMV-50 Operations Manual Copyright illunis, LLC 9/20/2019 Page 10
Installing prerequisite software:
The status of these items can be checked in the Control Panel ->
Programs and Features listing. If necessary download and install the
following prerequisites.
1. .NET Framework 4.6.1 to be installed from:
https://www.microsoft.com/en-us/download/details.aspx?id=49981
2. Visual C++ 2010 Redistributable from:
https://www.microsoft.com/en-us/download/details.aspx?id=14632
3. Visual C++ 2013 Redistributable from:
https://www.microsoft.com/en-us/download/details.aspx?id=40784
Getting Started Camera Link
CMV-50
Indice
Altri manuali illunis Macchina fotografica digitale
