Imperial Kitchen Ventilation 1942E Guida all'installazione

1900E & 1900ENV

Installation Instructions

Warranty Information

425 Apollo Street

Brea, CA 92821

www.imperialhoods.com

(800) 851-4192

DO NOT THROW AWAY,

PROPERTY OF THE HOME OWNER!

ECON/5.26.20

Unit is to be hardwired.

Adding a Power Cord will void the warranty.

Imperial Cal Products, Inc.

Read Before Starting Installation! Inspect your range hood prior to installing!

Any cosmetic defects must be reported to us prior to installation.

Once this hood is installed, ICP will NOT accept any responsibility

for any cosmetic blemishes, scratches or dents in the Canopy.

Save all original packaging if you wish to return for any reason!

FIRST:

Check your local building and electrical codes.

WARNING:

To reduce the risk of fire or electrical shock, Do Not use any two speed motor units with a Solid

State control devise.

CAUTION:

To reduce the risk of fire or personal injury and to properly exhaust air, be sure to duct air to the

outside. DO NOT vent exhaust air into spaces within wall, attics, ceilings, crawl spaces or

garages. For general ventilation use only. Do not use to Exhaust Hazardous or Explosive

Materials and Vapors. When venting to the outside make duct run as short and straight as

possible. Avoid using elbows if at all possible as this will reduce your performance. Every

elbow will decrease the performance and we will not guarantee the effectiveness of the range

hood.

No Performance Warranty when used above BBQ Style Grills.

DO NOT use duct pipe smaller than the outlet duct opening on the hood, this will reduce

performance and void the warranty. DO NOT use flex ducting. Also, use either a Roof Cap or

Wall Cap to end run. Be sure that all joints are taped securely in place. It is essential to have the

proper distance between the bottom of the range hood and the cooking surface below. In most

cases the cooking appliance manufacturers specifications will establish the fire safe minimum

distance required, although there are other factors to consider:

 Local Building Codes

 Cross directional air movements ie: open windows, air conditioning/heating outlets, cooling

fans, etc.

 Overall size of the cooking appliance and surrounding countertop surfaces.

 Range hood model selected.

For best performance distance between cooking surface and the bottom of the hood is 30” and

36”. Check local codes and appliance specifications. Keep in mind, increasing the distance will

decrease the performance.

DISCLAIMER

Imperial assumes no liability regarding the improper installation or misapplication of its products. It

is the installer’s responsibility to check for proper installation. Under no circumstances will Imperial

be liable for any labor charged or travel time incurred installation of its products. Damage caused

by improper installation is the installers responsibility and Imperial assumes no liability.

WARNING: This product can expose you to certain chemicals, which are known to the State of California to cause

cancer or birth defects or other reproductive harm. For more information to go: www.P65WARNINGS.ca.gov.

Economy Series Installation Details:

MODELS

1900E, 1900ENV

CABINET: Be sure that the cabinet bottom is level, side to side and front to rear.

For the Vented Unit (1900E) you will need to cut an 8” x 8” hole in the bottom of the cabi-

net, 3/4” in from the rear wall and on center line. For the Non-Vented model (1900ENV)

there is no need for a duct pipe cut out. Shelves and top to be cut to clear 7” round pipe to

line up with the bottom cabinet cut out. Also, cut holes for electrical wires for both Vented

and Non-Vented.

ELECTRICAL: Bring enough wire into cabinet to reach in front of vent pipe. Enter cabinet

3 1/4” left of center and 1 1/2” from wall for vented and non-vented units. Remove

electrical box cover before mounting hood. Units are to be hard wired. It is not

recommended to add a power-cord. Adding a power cord can loosen existing wires

inside junction box causing electrical failure.

NOTE: Be sure to remove black electrical tape that holds the damper blades closed.

MOUNTING: Insert canopy below the cabinet, being sure your vent opening and electrical

cut outs line up with cabinet cut outs. Use the Key Hole mounting holes to secure the

canopy. After hood is mounted attach house wires to leads in the hood. Secure locknut to

conduit and check wiring for compliance to local building codes.

FINISH: Replace electrical box cover. Connect duct and tape all joints. Install 40 Watt bulb

and replace Filter. (bulbs not included)

WARNING:

To reduce the risk of fire or electrical shock DO NOT use the “E” series with any solid-state

speed control device.

1900ENV

1900E

Imperial Cal Products, Inc.

To order replace parts or schedule service please call our office at (800) 851-4192 or use our

website… www.imperialhoods.com.

PARTS:

When ordering Parts we need the following information:

 Model Number (not serial number) found on UL label inside hood.

 Exact dimensions (in the case of filters)

You can find the model number on the inside of your hood on our UL label. There will be a

several model numbers listed, your model number should have some kind of mark next to it

to indicate the exact model you have.

In the case of Filters we will need the exact dimensions of the filter needed. Indicate which

side has the pull tabs on it. Filters are not a warranty replacement part. With care your filters

should last many years.

Payment on Parts is handled one of three ways: PrePaid (you send a check prior to our Ship-

ping), call with credit card information, VISA or MasterCard, COD or Cash if you decide to

“Will Call”.

Our Will Call hours are 8:30 to 3:30, Monday through Friday.

SERVICE:

When calling in for Service we need the following information:

 Model Number (not serial number)

 Proof of Purchase

 Name of company you purchased the hood through.

 Name & Phone number of the person to contact to set up the service call.

 Full address of the location where service is to be done.

1 Year Parts Only

Maintenance & Warranty Information

This product has the simplest of cleaning requirements. Clean filters often for the best

performance. How often depends on amount and type of cooking. Use hot water and a

degreaser. When cleaning a painted hood, wash it with mild, soapy water ONLY! Wipe the

hood thoroughly with clean water and dry with soft cloth. When cleaning Stainless Steel use a

cleaner specifically for Stainless Steel. Always rub with the grain using non-abrasive cleaning

materials. AVOID detergents, disinfectants or cleaning products in aerosol cans. NEVER use

abrasive scouring powders on your hood! Some cleaning chemicals may damage the hood

finish!

Clean Fan, Filter and Grease Laden

Surfaces FREQUENTLY

 Economy Models 40 Watt Incandescent OR equivalent LED bulb.

***Bulbs not included on any model.***

Warning: Do not use any bulbs that are not instructed by manufacturer.

Your Imperial Warranty:

MUST show proof of original purchase date is needed to obtain service under warranty.

1900E or 1900ENV: One Year Limited Warranty on Parts Only.

NOTE:

Service companies will perform Warranty Service, Monday through Friday from 7 a.m.—4:

p.m. The service company will call and schedule a date and time with a 4 hour window. If the

service company arrives at your location, during the scheduled date and time, and no one is

home, you will be charged a trip charge by the service company for a return service call.

1900E or 1900ENV we will provide parts only for 1 year from date of original purchase.

Call for service or parts at (800) 851-4192

ITEMS IMPERIAL WILL NOT PAY FOR

1. Service calls to correct the installation of your appliance, to instruct you how to use your

appliance, to replace or repair house fuses or the correct housing wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs or filters.

3. Repairs when your appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God,

improper installation, installation not in accordance with electrical or plumbing codes.

5. Replacement parts or repair costs for units operated outside the United States.

6. Pickup and delivery. This appliance is designed to be repaired in the home.

7. Repairs to parts or systems resulting from unauthorized modification made to the

appliance.

8. Expenses for travel and transportation for product service in remote locations.

9. The removal and reinstallation of your appliance if it is installed in an inaccessible location

or is not installed in accordance the published installation instructions.

10. Replacement parts or repair labor costs when the appliance is used in a country other

than the country in which it was purchased.

SAFETY INSTRUCTIONS

Read and Save These Instructions

Warning: To reduce the risk of fire, electrical shock or injury to persons, observe the

following:

A. Use this unit only in the manner intended by the manufacturer. If you have any questions,

contact the manufacturer. Before servicing or cleaning unit, switch power off at service

panel and lock Service Disconnecting Means to prevent power from being switched on

accidentally. When the Service Disconnecting Means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Warning: To reduce the risk of a range top grease fire:

A. Never leave surface units unattended at high settings. Boil-overs cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when Flambéing foods (i.e. Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fans or

filters.

D. Use proper pan size. Always use cookware appropriate for the size of the surface

element.

Warning: To reduce the risk of injury to persons in the event of a range

top grease fire, observe the following:

 SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the

burner. BE CAREFUL TO PREVENT BURNS. If flames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

 NEVER PICK UP A FLAMING PAN - you may be badly burned.

 DO NOT USE WATER, including wet dishcloths or towels, violent steam explosion will

result.

 Use an extinguisher ONLY if:

 You know you have a Class ABC extinguisher and you already Know how to use it.

 The fire is small and contained in the area where it started.

 The fire department is being called.

 You can fight the fire with your back to an exit.

Warning: To reduce the risk of fire, electrical shock or injury to persons, observe the

following:

A. Installation work and electrical wiring must be done by a qualified person or persons in

accordance with all applicable codes and standards, including fire-rated construction.

B. Sufficient air is needed for proper combustion and exhausting of gases through the flue of

fuel burning equipment to prevent back drafting. Follow the heating equipment manufac-

turer’s guideline and safety standards such as those published by the National Fire Pro-

tection Association (NFPA), and the American society for Heating, Refrigeration & Air

conditioning Engineers (ASHRAE), and the local code authorities.

C. When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other

hidden utilities.

D. Ducted fans must always be vented to the outdoors.

Warning: To reduce risk of fire, use only Smooth Metal Ducting!

1900E, & 1900ENV

Instructions d'installation

Informations sur la garantie

425 Rue Apollo

Brea CA 92821

www.imperialhoods.com

(800) 851-4192

PROPRIÉTÉ DU PROPRIÉTAIRE DE LA MAISON,

NE PAS JETER !

Impériale Cal Products, Inc.

Lire avant de commencer l'Installation !

Inspecter avant d'installer votre hotte de cuisinière !

Les défauts cosmétiques doivent nous être signalés avant l'installation.

Une fois cette hotte est installée, ICP n'acceptera aucune responsabilité

pour toute les imperfections cosmétiques, rayures ou bosses dans la canopée. En-

registrer tous les emballages d'origine si vous voulez

retourner pour n'importe quelle raison !

TOUT D'ABORD :

Vérifiez vos locales de construction et les codes de l'électricité.

AVERTISSEMENT :

Pour réduire le risque d'incendie ou d'électrocution, ne pas utiliser n'importe quelle unité

de moteur à deux vitesses avec un Solid State devise de contrôle.

MISE EN GARDE :

Pour réduire le risque d'incendie ou de lésions corporelles et pour bien évacuer l'air, n'ou-

bliez pas d'évacuer l'air vers l'extérieur. N'évacuez pas l'air dans des espaces dans le

mur, les greniers, les plafonds, les espaces confinés ou les garages. Pour une utilisation

de ventilation générale seulement. N’utilisez pas pour épuiser dangereux ou des matières

explosives et les vapeurs. Lorsque la décharge à l'extérieur faire conduit tourner aussi

court et aussi droit que possible. Évitez d'utiliser des coudes si possible. Si les coudes

sont utilisés, nous recommandons que le premier coude est 24 "d'ouverture sur le capot

(minimum de 12 po) et au moins 24" entre elle et le coude du prochain. Nous ne recom-

mandons vivement aucuns plus puis exécutez deux coudes de 90 degrés dans n'importe

quel canal. Aucune garantie de Performance lors de l'utilisation au-dessus des

grilles de Style BBQ.

N'utilisez pas conduit plus petite que la sortie du conduit d'ouverture sur le capot, cela

réduira les performances et annuler la garantie. N'utilisez pas de conduits flexibles. Aussi,

utilisez soit un capuchon de toit ou de mur à la course de fin. N'oubliez pas que tous les

joints sont scellés

solidement en place. Il est essentiel d'avoir la bonne distance entre le bas de la hotte et la

table de cuisson ci-dessous. Dans la plupart des cas, les spécifications de fabricant appa-

reil cuisson établira la distance minimale sécuritaire de feu requise, bien qu'il existe

d'autres facteurs à considérer : LocalBâtimentCodes Traverser c'est à dire les mouve-

ments d'air directionnel : ouvrir les fenêtres, prises d'air conditionné/chauffage, refroidis-

sement, ventilateurs, etc.. Taille globale de l'appareil de cuisson et les surfaces environ-

nantes de comptoir. Hotte d'aspiration modèle sélectionné.

Détails d'Installation de série économie :

MODÈLES

1900E, 1900ENV

Armoire : N'oubliez pas que la base de l'armoire est de niveau, côté à l'autre et d'avant en

arrière. Pour l'unité de décharge (1900E) vous devrez couper un trou de 8 « x 8 » en bas

de l'armoire, 3/4 "de la paroi arrière et sur la ligne médiane. Pour le Non-ventilé modèle

(1900ENV) il n'est pas nécessaire pour un tuyau de conduit, découper. Étagères et haut à

couper pour effacer 7 "tour tuyau à s'aligner avec le fond armoire à découper. Aussi, cou-

per les trous pour les fils électriques pour ventilé et Non-ventilé.

Électrique : Talon assez câble dans l'armoire pour rejoindre en face du tuyau d'évacua-

tion. Entrez armoire 3 1/4 "gauche du centre et 1 1/2 po du mur pour unités ventilées et

non ventilé. Enlever le couvercle de boîte de jonction avant hotte de montage.

Remarque : N'oubliez pas de retirer le ruban isolant noir qui maintient les lames clapet

fermés.

De montage : Insert couvert sous l'armoire, en veillant à coupe votre évent ouverture et

électrique des sorties ligne

vers le haut avec placard coupe outs. Utilisez le trou de clé trous de fixation pour maintenir

le pavillon. Après le montage hotte fixer fils de la maison au conduit de la hotte. Contre-

écrou pour conduit de garantir et vérifier le câblage pour la conformité aux codes du bâti-

ment locaux.

Finition : Couvercle de boîte de jonction remplacer. Raccorder le conduit et tous les joints

de bande. Install modèles à incandescence de 40 Watt bulb and Remplacer filtre à.

AVERTISSEMENT :

Pour réduire le risque d'incendie ou d'électrocution, ne pas utiliser la série « E » avec un

dispositif de contrôle de vitesse à l'état solide.

1900ENV

1900E

Impériale Cal Products, Inc.

Pour commander des pièces ou annexe service, veuillez appeler notre bureau au (800)

851-4192 ou utiliser notre site Web... www.imperialhoods.com.

PIÈCES :

Lorsque vous commandez des pièces nous avons besoin des informations suivantes :

Numéro de modèle (pas les numéro de série) sur l'étiquette d'UL à l'intérieur de la hotte.

Dimensions exactes (dans le cas des filtres)

Vous pouvez trouver le numéro de modèle à l'intérieur de votre hotte sur notre label UL. Il

y a plusieurs numéros de modèle dans la liste, votre numéro de modèle doivent avoir un

point de couleur ou de marque à côté de lui pour

indiquer exactement le modèle vous avez.

Dans le cas de filtres, nous devrons les dimensions exactes du filtre

nécessaire. Indiquer de quel côté a les tirettes sur elle. Les filtres ne sont pas une pièce

de rechange de garantie. Avec soin vos filtres doivent depuis plusieurs ans.

Paiement sur pièces est assurée de trois façons : prépayé (vous envoyez un chèque

avant l'expédition), appelez avec informations de carte de crédit, VISA ou MasterCard,

morue ou argent comptant si vous décidez de "Appellera". Our appellera heures sont de

08:30 à 03:30, du lundi au vendredi.

SERVICE :

Lors de l'appel service nous avons besoin des informations suivantes :

 Numéro de modèle (pas les numéro de série)

 Preuve d'achat

 Nom de l'entreprise qu'a été achetée le capot à travers.

 Nombre nom et téléphone de la personne à contacter pour configurer

'appel de service.

 Adresse complète de l'emplacement où le service doit être fait.

(1) Un an pièces uniquement.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Imperial Kitchen Ventilation Cappa di ventilazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WH1948PSR-SS Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WH1900B-8 Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation Powered Liner-C2000 Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WH1900 Series Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation Slim Line Series Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WHN2000 Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WHP1900 Series Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation 3000 Series Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WH1900-10 Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WHP1930BP1-BL Manuale utente

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation G3000SD2 Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation 30NV Manuale utente

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation 2000PS-IS-8-SS Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WH2000 Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation C2000B-8 Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation C2000 Series Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation C2060PS1TWBSS Guida all'installazione

Imperial Kitchen Ventilation

Imperial Kitchen Ventilation WHN2042PSSB-8-SS Guida all'installazione

Manuali Cappa di ventilazione popolari di altre marche

emmeti

emmeti RECUPA MED A-140 Guida

Nibe

Nibe F135 Manuale utente

Kuppersberg

Kuppersberg INTRO 60 Istruzioni di installazione e manutenzione

Zephyr

Zephyr Spruce AK9834BS Guida all'installazione

Hisense

Hisense MH6INBG Manuale utente

Miele

Miele DA 1255 Manuale utente

Broan

Broan 46000 Manuale utente

GE Profile PV977 Istruzioni originali

FALMEC

FALMEC FFRIA24W5FS Manuale utente

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuale utente

Küppersbusch

Küppersbusch DX ISLA Manuale utente

ETNA

ETNA AV360RVS Manuale utente

JUNO

JUNO JDF603E6 Manuale utente

Miele

Miele DA 6708 D Manuale utente

Tricity Bendix

Tricity Bendix LE 150 Manuale

AEG

AEG X68163BV1 Manuale utente

AEG

AEG 125 D Manuale utente

Smeg

Smeg KSEV97X Manuale utente