Inateck BR1003 Manuale utente
Instruction Manual
English · Deutsch · 日本語 · Français
Italiano · Español
BR1003 Bluetooth transmitter and receiver
1
English
Overview
3.5mm audio port (AUX)
Bluetooth receiver mode (RX)
LED indicator
Multi-function button （MFB）
Bluetooth transmitter mode (TX)
Micro USB charging port
Charging
The WHITE LED indicator will flash three
times continuously if the battery level is
low, which indicates charging is necessary.
2
1. Plug the USB end of the charging cable
to a USB charging port or any active
USB port (charging power: DC 5V).
Connect the Micro USB end of the
charging cable to the charging port of
the BR1003.
2. The WHITE LED indicator will turn on
when charging.
3. The LED indicator will automatically turn
o when the device is fully charged. It
takes up to 2 hours to fully charge the
Bluetooth adapter.
Note
a. Poor quality power adapters do not
provide a stable current , which may
generate current noises when in use.
b. Please recharge the device once a
month if the device is not in regular use.
Lithium-Ion batteries continue to slowly
discharge (self-discharge) when not in
use or while in storage.
Common Functions
1. Power On/O
Press and hold the Multifunction Button
for 3 seconds.
Power on: the LED indicator will blink
blue.
Power off: the LED indicator will blink
white and automatically turn o.
3
2. Automatically Pairing with Previously
Paired Devices
BR1003 will enter pairing mode
automatically when powered on for
the first time. BR1003 can remember
previously paired devices and
will attempt to pair with devices
automatically, without going into
pairing mode.
3. Quick Pairing
Quickly double-click the Multifunction
Button to enter pairing mode after the
BR1003 is powered on.
4. TX/RX Mode Switch
RX/TX mode can only be successfully
switched after the adapter is turned o
for 5 seconds.
Note: Turn off the BR1003 and restart
it after 5 seconds if the mode switch is
not functioning properly.
5. Clear Pairing History
Please follow the guides below to clear
the pairing history if pairing failures are
encountered:
1) Turn off the BR1003, switch TX (RX) mode
to RX (TX) mode after 5 seconds, and then
restart the BR1003.
2) Turn o the BR1003, switch RX (TX) mode to
TX (RX) mode after 5 seconds.
After that, the pairing history of TX (RX)
mode will be cleared.
4
6. RX Mode: Pause/Play
Press the Multifunction Button to pause
or play while playing music.
7. Auto-o
In RX mode, the BR1003 will automatically
power off if there is no device to be
connected within 6 minutes. The
BR1003 will not turn o automatically in
TX mode.
Bluetooth Transmitter Mode (TX)
The transmitter mode enables the BR1003
to transmit audio signal from non-
Bluetooth devices like TV or computer to
Bluetooth headphones or speakers. When
BR1003 is in TX mode, you can connect
BR1003 with a non-Bluetooth audio
device like a TV / computer via an AUX
audio cable. Then connect the BR1003
with Bluetooth headset / speakers etc. via
Bluetooth.
5
LED Indicator
LED Indicator (TX Mode) Status
rapidly Flashing blue In pairing mode
Blue LED flashes twice
every 3 seconds
Automatically Pairing with
Previously Paired Devices
Solid blue Successfully paired
How to Use
1. Pairing
1) Set your Bluetooth enabled devices like
Bluetooth headphones or speakers to pairing
mode.
2) Set the BR1003 to TX mode. Then press and
hold the Multifunction Button for 3 seconds to
turn it on. Tap the Multifunction Button twice
to enter pairing mode with the LED indicator
keeps rapidly flashing blue. The BR1003 will
automatically exit pairing mode if there is no
device to be connected within 2 minutes.
3) Place your Bluetooth audio receiving devices like
earphones or speakers closely to the BR1003.
After approximately 30 seconds, pairing will be
completed. The BR1003 LED indicator will turn
solid blue.
4) Connect the BR1003 to your audio output
devices like TV through a 3.5mm audio cable.
Note:
a. BR1003 will enter pairing mode automatically when
powered on for the rst time.
b. BR1003 can only automatically re-pair to the 4
most recently connected devices.
6
2. Pair with two devices at the same time
In TX mode, BR1003 is able to pair with
two Bluetooth stereo earphones/speakers
at the same time. And both can play music
at the same time.
1) Follow the previous instructions in the “Pairing”
section to pair the BR1003 with your rst device.
Turn off your first device after successfully
pairing it with the BR1003.
2) Tap the Multifunction Button twice to pair and
connect to your second device. Turn off the
BR1003 after successfully pairing it with your
second device.
3) Turn on your rst device and wait for 10 to 20
seconds. Both of your devices are now ready
for pairing. Turn on the BR1003, the devices will
automatically connect in.
Note:
a. Please turn o the BR1003 and restart it to re-pair
if two devices cannot play music at the same
time. If the problem still exists after repeating
the whole steps above, please contact Inateck
Support at: [email protected].
b. It is advised to switch off the Bluetooth
function of your other devices to avoid signal
interference.
c. We have performed the compatibility testing
with various Bluetooth chipsets on the market.
But please note not all these chipsets use the
same software, compatibility issue might still
encounter for some Bluetooth devices. Please
contact our customer support team for help.
d. BR1003 can automatically re-pair to the 2 most
recently connected devices.
7
Bluetooth Receiver Mode (RX)
When BR1003 is in RX mode, you can
connect BR1003 with a non-Bluetooth
audio device like a headphone/ speaker/
audio amplifier via an AUX audio cable.
Then connect BR1003 with Bluetooth
enabled devices like smartphones or
laptops etc. via Bluetooth. Therefore, non-
Bluetooth audio device like a headphone/
speaker can receive audio signals via
Bluetooth.
LED Indicator
LED Indicator(RX Mode) Status
Blue and white LED ash
alternately
In pairing mode
Blue LED flashes twice
every 3 seconds
Automatically Pairing with
Previously Paired Devices
Solid blue Successfully paired
8
How to Use
1. Pairing
1) Set the BR1003 to RX mode before turning it on.
2) Turn on the BR1003 by pressing and holding the
Multifunction Button for 3 seconds. Rapidly tap
the Multifunction Button twice to enter pairing
mode with the LED indicator ashes blue and
white alternately.
3) Activate the Bluetooth function on your
transmitting device and nd "Inateck BR1003"
to connect. The LED indicator will turn solid
blue after successfully paired.
4) Connect the BR1003 to your headphone or
home stereo playback device through a 3.5mm
audio to enjoy the music.
Note
a. If a PIN code is required for pairing, try 0000,
8888, 1111 or 1234.
b. This product has no built-in microphone which
cannot be used for hands-free calls.
c. BR1003 can remember 8 paired devices, when
the number of paired devices exceeds 8, the
rst one will be replaced.
2. Pair with two devices at the same time
In RX mode, BR1003 is able to pair with two
Bluetooth enabled smartphones/tablets at the
same time. Only one device can play music at any
time. You have to stop the music on one device
to play on the other. Please follow the instructions
below:
1) Follow the previous instructions in the “Pairing”
section to pair the BR1003 with your rst device.
9
Disable the Bluetooth function on your first
device after successfully pairing BR1003 with it.
2) Rapidly tap the Multifunction Button twice to
pair and connect to your second device
3) Turn o the BR1003 after successfully pairing it
with your second device. Activate the Bluetooth
function on your rst device, turn on the BR1003
after about 20 seconds. After approximately 30
seconds, pairing will be completed.
Product Specications
Bluetooth version V4.1，Class Ⅱ
Chipset CSR BC8670
Bluetooth receiver working time Approx 12 hours
Bluetooth transmitter working
time
Approx 13 hours
Full recharging time Approx 2 hours
Bluetooth prof ile A2DP
Support dual connection
(connect two devices)
Support
CODEC aptX Low Latency,
aptX，SBC
Transmission distance 10m
Battery 250mAh rechargeable
lithium battery
Charging supply DC 5V，≥300mA
Working temperature -10~55℃
Net weight Approx. 18g
Dimension 43.8*43.8*12.4mm
Bluetooth Operating Frequency 2402-2480MHz
Bluetooth transmission Power 4dBm
Altri manuali per BR1003
3
Indice
Lingue:
Altri manuali Inateck Ricevitore
