Indy Presenter Manuale utente
Indy Presenter™ Owner’s Guide
Document Number 007-9224-001
Indy PresenterTM Owner’s Guide
Document Number 007-9224-001
CONTRIBUTORS
Written by Judy Muchowski
Illustrated by Dany Galgani, Kay Maitz, Derrald Vogt
Engineering contributions by Dan Evanicky, Bert Keely, Alice Meng, Steve Siefert
Production by Chris Glazek
© Copyright 1994, Silicon Graphics, Inc.— All Rights Reserved
This document contains proprietary and confidential information of Silicon
Graphics, Inc. The contents of this document may not be disclosed to third parties,
copied, or duplicated in any form, in whole or in part, without the prior written
permission of Silicon Graphics, Inc.
RESTRICTED RIGHTS LEGEND
Use, duplication, or disclosure of the technical data contained in this document by
the Government is subject to restrictions as set forth in subdivision (c) (1) (ii) of the
Rights in Technical Data and Computer Software clause at DFARS 52.227-7013 and/
or in similar or successor clauses in the FAR, or in the DOD or NASA FAR
Supplement. Unpublished rights reserved under the Copyright Laws of the United
States. Contractor/manufacturer is Silicon Graphics, Inc., 2011 N. Shoreline Blvd.,
Mountain View, CA 94043-1389.
Dukane is a registered trademark of Dukane Corporation. Silicon Graphics is a
registered trademark and Indy, Indy Presenter, and Indybag are trademarks of
Silicon Graphics, Inc.
iii
Contents
Introduction ix
1. Installing the Indy Presenter Hardware
and Software 1
The Indy Presenter Package 1
Identifying Your Indy’s Graphics Board 2
Checking the PROM Chip Version 3
Removing the Top Cover 6
Attaching the Wrist Strap 7
Removing the GIO Option Board 8
Replacing the PROM in an Indy Workstation 12
Removing the Indy Graphics Board 12
Replacing the PROM Chip 15
Replacing the Graphics Board 19
Installing the Indy Presenter Adapter Board 23
Installing the Indy Presenter XZ Adapter Board 30
Turning Off Your Indy Workstation 31
Removing the Top Cover 32
Attaching the Wrist Strap 33
Installing the Board 33
Replacing the Top Cover and Connecting the Cables 41
Installing the Software 42
iv
Contents
2. Setting Up and Using the Indy Presenter 43
Setting Up the Indy Presenter 43
Connecting the Cables 44
Using the Indy Presenter 48
Turning On the Indy Presenter 48
Turning Off the Indy Presenter 49
Setting Up on the Dukane Customized Projector 49
Using the Indy Presenter Software 54
Using the Monitor Control Panel 54
Turning on the Indy Presenter 54
Restarting the Indy Presenter 55
Adjusting the Brightness 55
Switching to 15-Bit Mode 56
Using the Audio Control Panel 56
Adjusting the Volume and Tone of the Speakers 57
Using Headphones 58
Transporting the Indy Presenter 58
Transporting the Dukane Overhead Projector 59
Cleaning and General Care of the Indy Presenter 60
Using a Screen Saver 61
3. Troubleshooting 63
Common Problems 63
No Image on the Indy Presenter 63
Image Is Too Light or Too Dark 64
Faint Vertical Streaks Above or Below Edges of Windows 64
No Image on the Overhead Projector or Image Is Reversed 65
No Sound From the Stereo Speakers 65
Diagnostics Tests For the Indy Presenter 66
Removing the Indy Presenter Adapter Board 67
Removing the Indy Presenter XZ Adapter Board 69
Returning the Presenter to Silicon Graphics 71
Product Support 71
v
4. Technical Specifications and Regulatory Information 73
Technical Specifications 73
Manufacturer’s Regulatory Declarations 76
Electromagnetic Emissions 76
Electrostatic Discharge 77
Shielded Cables 77
Product Safety 77
A. About Liquid Crystal Display (LCD) Technology 79
Display 79
Differences Between LCD and CRT Technology 80
Quality 81
Backlight Brightness 81
Index 83
vi
Contents
vii
Figures
Figure 1-1 System Shutdown Notifier 3
Figure 1-2 Okay to Power Off Notifier 4
Figure 1-3 Starting Up the System Notifier 4
Figure 1-4 Turning Off the Indy Workstation 5
Figure 1-5 Removing the Top Cover From the Indy Workstation 6
Figure 1-6 Indy Workstation With Single-Width GIO Option
Board 8
Figure 1-7 Removing the Screws From the GIO Board Connector 9
Figure 1-8 Removing the Screws From the GIO option Board 10
Figure 1-9 Disconnecting the GIO Option Board 10
Figure 1-10 Removing the Hexnut Screws From the Rear Panel 12
Figure 1-11 Removing the Screws From the Graphics Board 13
Figure 1-12 Disconnecting the Graphics Board From the System
Board 14
Figure 1-13 Locating the PROM Chip on the System Board 15
Figure 1-14 Removing the PROM Chip 16
Figure 1-15 Lining Up the PROM Chip 17
Figure 1-16 Pressing the PROM Chip Into the Socket 18
Figure 1-17 Positioning the Graphics Board Over the System
Board 19
Figure 1-18 Seating the Graphics Board’s Connectors 20
Figure 1-19 Standoff Screw 21
Figure 1-20 Inserting the Screws on the Graphics Board 21
Figure 1-21 Replacing the Screws on the Backplane 22
Figure 1-22 Removing the Faceplate From the GIO Option Port 23
Figure 1-23 The Indy Presenter Adapter Board 24
Figure 1-24 Positioning the Adapter Board Over the Graphics
Board 25
viii
Figures
Figure 1-25 Seating the Adapter Board’s Connectors 26
Figure 1-26 Inserting the Screws on the Rear Panel 27
Figure 1-27 Securing the Adapter Board 28
Figure 1-28 Connecting the Audio Cable 29
Figure 1-29 Turning Off the Indy Workstation 31
Figure 1-30 Removing the Top Cover 32
Figure 1-31 The Indy Presenter XZ Adapter Board 33
Figure 1-32 Removing the Faceplate From the GIO Option Port 34
Figure 1-33 Installing the Metal Bracket 35
Figure 1-34 Inserting the Screws on the Exterior of the Bracket 36
Figure 1-35 Positioning the Indy Presenter XZ Adapter Board 37
Figure 1-36 Inserting the Screws on the XZ Adapter Board 39
Figure 1-37 Attaching the External Screws 40
Figure 1-38 Replacing the Top Cover on the Indy Workstation 41
Figure 2-1 Placing the Indy Presenter on Top of the Indy
Workstation 44
Figure 2-2 Interface Cable Connector 45
Figure 2-3 Connecting the Interface Cable to the Indy Presenter 45
Figure 2-4 Connecting the Interface Cable: Indy Presenter
Adapter 46
Figure 2-5 Connecting the Interface Cable: Indy Presenter XZ
Adapter 46
Figure 2-6 Connecting the Power Cable 47
Figure 2-7 Turning On the Indy Workstation and the Indy
Presenter 48
Figure 2-8 Removing the Backlight Panel 51
Figure 2-9 Placing the Presenter on the Overhead Projector 52
Figure 2-10 Replacing the Backlight Panel 53
Figure 2-11 Rotating the Base for Packing the Indy Presenter 59
ix
Figure 3-1 Removing the Audio Cable 67
Figure 3-2 Removing the External Screws 67
Figure 3-3 Removing the Screws from the Adapter Board 68
Figure 3-4 Removing the Audio Cable and the External Screws 69
Figure 3-5 Removing the Screw from the XZ Adapter Board 70
Figure 4-1 Japanese VCCI Class 1 Statement 76
x
Figures
Indice
