InFocus CEILING MOUNT LP 1000 SERIES Manuale utente
Installation Guide
LP 1000 Series
Ceiling Mount
Installation Guide
LP 1000 Series
Installationhandbuch zur
Deckenbefestigung
English. . . . . . . . . . . . .1
Deutsch . . . . . . . . . .13
010-0154-00
Copyright © 1998 by In Focus, Inc.
Wilsonville, Oregon. All rights reserved..
Copyright © 1998 by In Focus, Inc.
Wilsonville, Oregon, USA. Alle Rechte vorbehalten.
1
CEILING MOUNT INSTALLATION GUIDE
The LP 1000 Series LiteMountTM makes it easy to
hang your projector from the ceiling for fixed
installation use in meeting, auditorium and
training room settings.
WARNING: This installa-
tion must be performed in
compliance with your local
building code require-
ments. Local require-
ments take precedence
over any instructions given
in this guide.
You must determine the suitability of this prod-
uct for your intended use and assume all risk
and liability in connection therewith. In Focus
recommends that a professional contractor or
other facilities professional assist you in mount-
ing this device. Be sure to take precautions to
meet all local building codes.
Additional LiteMount Products
In Focus offers two additional LiteMount prod-
ucts that may make your ceiling mount installa-
tion easier.
•The LiteMount False Ceiling Plate
(SP-LTMT-PLT) is designed for suspended ceil-
ings with acoustic tiles. It mounts in your ceil-
ing in place of a ceiling tile. It is pre-drilled
with holes to install the LiteMount brackets.
•The LiteMount Pipe Tubing Extension (SP-
LTMT-EXT) allows you to install the projector
in a room with a high ceiling. With the exten-
sion, you can place the projector from 12”
(30.5) to 46” (117 cm) from the ceiling.
Contact your In Focus dealer to order these prod-
ucts.
Placing the Projector
Refer to the LP 1000 User’s Guide for image dis-
tance, size, and angles of projection to determine
where to install the ceiling mount to meet your
projection needs.
Contents
2
Contents
The LP 1000 Series Ceiling Mount package con-
tains:
NOTE: The maximum
load the ceiling mount can
support is 50 pounds.
1Installation Guide
2ceiling mount base box
dimensions: 11.6” x 10” x 1.5”
(29.5 x 25 x 3.8 cm)
weight: 3.5 lbs (1.6 kg)
3projector mounting bracket
dimensions: 12” x 11.5” x 1.5”
(30.5 x 29.2 x 3.8 cm)
weight: 4.0 lbs (1.8 kg)
4hardware for installing the projector mount-
ing bracket on the projector:
•three (3) 4mm Phillips-head screws
•three (3) 4mm quick release sleeves
•one (1) 10/32 knurled knob screw
5hardware for installing the projector (with
mounting plate) to the base box in the ceiling:
•four (4) 6x12 mm knurled knob screws
•two (2) 6 mm flat washers
•two (2) 10 mm conical spacers
3
Install the Ceiling Mount Base Box on the Ceil-
ing
WARNING: The ceiling
structure must be able to
support at least 5 times
the weight of the projector
and mounting hardware. If
not, it must be reinforced
according to your local
building codes.
Instructions for installing the ceiling mount on
the LiteMount False Ceiling Plate and the Lite-
Mount Pipe Tubing Extension are given in this
installation guide. If you have not purchased
either of these products, consult a professional
contractor or other facilities professional to
ensure a safe installation.
Please refer to the LiteMount False Ceiling Plate
and LiteMount Pipe Tubing Extension installa-
tion instructions for lists of included hardware.
1Center the ceiling mount base box on the ceil-
ing plate as shown in Figure 1. Make sure the
front of the base box faces forward toward
your projection screen. The front side of the
base box is the only surface without drilled
holes.
2a LiteMount False Ceiling Plate - Align the
holes in the base box with the threaded studs
on the plate. Install the 4 washers and nuts as
shown in Figure 1.
NOTE: Refer to the
Installation Instructions
that came with the Lite-
Mount False Ceiling Plate
and the LiteMount Pipe
Tubing Extension for
important additional infor-
mation.
2b LiteMount Pipe Tubing Extension - Line up
the holes in the base box with the holes in the
plate at the end of the pipe extension. Install
the hardware as shown in Figure 2.
Install the Ceiling Mount Base Box on the Ceiling
4
3Place the ceiling plate or pipe extension in the
ceiling so that the base box hangs down into
the room.
WARNING: If the
dropped ceiling is an air-
handling plenum, be sure
the cables are plenum-
rated, or install the cables
within conduit.
4Route the projector’s cables through your
ceiling and out the hole in the ceiling
(Figure 7).
FIGURE 1
Install the base box to the LiteMount False Ceiling Plate
make sure this
surface faces front
5
FIGURE 2
Install the base box to the LiteMount Pipe Tubing Extension
surface faces front
make sure this
Attach the Mounting Plate to the Projector
6
Attach the Mounting Plate to the Projector
1Set the projector on a table with the bottom
side up.
CAUTION: Use only the
hardware that is provided
with the LP 1000 Series
Ceiling Mount. Using
different hardware may
damage your projector.
2Insert the 3 screws into the 3 quick release
sleeves (Figure 3).
3Attach the screws and sleeves to the holes in
the projector as shown in Figure 3. Be careful
not to over-tighten the bolts.
4Align the keyholes in the mounting bracket
with the screws in the projector. Slide the
mounting bracket until the quick release
sleeves are at the top of the keyhole slot.
5Attach the 10/32 knurled knob to the projec-
tor in the location shown in Figure 3.
FIGURE 3
Attach the mounting plate to the projector
quick release screws
knurled knob
goes here
quick release screw
7
Hang the Projector on the Ceiling
1Loosely install the 12 mm knurled knobs, flat
washers, and conical spacers to the 2 hinge
pins on the base box (Figure 4).
FIGURE 4
Attach knurled knobs to the side of the base box
2Make sure your cables are pulled through the
center hole of the base box, then carefully lift
the projector and turn it upside down so the
mounting plate faces the ceiling.
3Insert the projector and mounting bracket
into the base box through the space between
the knurled knobs and base box (Figure 4).
Slide the projector bracket forward until the
knurled knobs rest fully in the vertical slots
and support the projector. Tighten the
knurled knobs completely.
slide projector
bracket here between
the base box and the knurled knob
knurled knob
knurled knob
spacer
washer
Hang the Projector on the Ceiling
8
F
IGURE 5
Install the projector in the ceiling base box
4Insert the remaining two 6 mm knurled
knobs through the rear slots in the mounting
bracket and into the holes on the sides of the
base box. Hand-tighten them.
FIGURE 6
Insert the knurled knobs to adjust the angle
Insert knurled knob
through this slot
Altri manuali per CEILING MOUNT LP 1000 SERIES
3
Indice
Lingue:
Altri manuali InFocus Accessori per proiettori
InFocus
InFocus CableWizard SP-CW3 Guida rapida
InFocus
InFocus LP130 Guida
InFocus
InFocus SP-LAMP-080 Guida
InFocus
InFocus IN42 Guida
InFocus
InFocus LP770 Manuale utente
InFocus
InFocus SP-LAMP-088 Guida
InFocus
InFocus SP-CEIL-001 Manuale utente
InFocus
InFocus IN2112 Guida
InFocus
InFocus LiteShow 4 DB+ Manuale utente
InFocus
InFocus LP 240 Istruzioni operative e di sicurezza
InFocus
InFocus SP-LAMP-090 Guida
InFocus
InFocus SP-CEIL-UNIV Guida
InFocus
InFocus LiteProLS Manuale utente
InFocus
InFocus LP 650 Guida
InFocus
InFocus LiteShow network adapter Manuale utente
InFocus
InFocus SP-CEIL-010 Manuale utente
InFocus
InFocus SP-CEIL-004 Manuale utente
InFocus
InFocus SP777 Manuale utente
InFocus
InFocus SP-LAMP-086 Guida
InFocus
InFocus LP790 Manuale utente
