INIM Electronics SmartLink-G Manuale del proprietario
SmartLink-G, SmartLink-GP
GSM Dialler
Programming
Manual
PATENT PENDING
0470
Programming manual
2
Copyright
The information contained in this document is the sole
property of INIM Electronics s.r.l. No part may be copied
without written authorization from INIM Electronics s.r.l.
All rights reserved.
Directive 1999/5/CE (R&TTE) compliance.
Hereby INIM Electronics s.r.l. declares that the
SmartLink-G and SmartLink-GP are in compliance with
the essential requirements and other relevant provisions
of Directive 1999/5/CE.
The full declarations of conformity of the above-
mentioned devices are available at URL:
www.inim.biz/dc.html.
3
Programming manual
Table of contents
Chapter 1 Overview ..................................... 5
Chapter 2 General information....................... 6
2.1 In-box documentation 6
2.2 Manual details 6
2.3 Addressees 6
2.4 Software information 6
2.5 Intellectual property rights 6
2.6 Key 6
Chapter 3 Programming the SmartLink-GP ......8
3.1 Introduction 8
3.2 Installing the SmartLeague software 8
3.3 SmartLeague software 9
3.4 Recommended programming flow 12
3.5 Settting up contact data 13
3.6 Setting up the SmartLink parameters 18
3.7 Programming the Inputs and Outputs —
IN&OUT 24
3.8 Programming the SmartLink-GP as an
Intrusion control panel 29
3.9 Associating incoming and outgoing calls with
actions 31
3.10 Programming event generated actions 34
3.11 Programming periodic events 43
3.12 Remote control of the SmartLink-GP via SMS
text messages 44
3.13 Programming the device via SMS messages
47
3.14 Remote control of SmartLink-GP via DTMF
tones 52
Appendix A Example wiring diagram intrusion con-
trol ........................................... 57
Appendix B Features not managed by the Smart-
Link-G model.............................. 59
4
Programming manual
Appendix C Default settings of the Smartlink-GP60
Appendix D Inhibit events for output control ....61
• Notes.........................................62
Overview 5
Programming manual
Chapter 1
Overview
The SmartLink is available in the following models:
• SmartLink-GP
•SmartLink-G
Besides the features of the SmartLink-G model, the SmartLink-GP model
also provides the following advanced features:
1. Intrusion control panel facility
2. Voice dialler (requires SmartLogos60 accessory board)
3. PSTN line call management
The Smartlink-G model does not provide these features.
This manual describes the Smartlink-GP features and programming process.
SmartLink-G users can skip the sections which refer to the advanced
features.
Refer to Appendix B for a detailed list of the Smartlink-GP advanced features
and flexibility-optimized software.
6 General information
Programming manual
Chapter 2
General information
2.1 In-box documentation
• Installation manual
• Programming manual (this manual)
The Installation manual is inside the device package. For extra copies of the
installation manual, please contact INIM electronics specifying the order code
shown in the Installation manual Appendix B.
2.2 Manual details
Title: SmartLink-G and SmartLink-GP Programming Manual
• Edition,Version: 2.10
• Month and Year of issue: October 2012
• Code: DCMPINE0SLINK
2.3 Addressees
• Installer
• Technical assistance
2.4 Software information
• Smartleague software version: 3.x.x
• Firmware version : 2.x.x
2.5 Intellectual property rights
The information contained in this document is private property. All rights
reserved.
No part of this document may be copied or reproduced unless expressly
authorized in writing by INIM Electronics, in particular the parts regarding
the device specified in the Installation Manual paragraph 2.8 Device identifier
INIM Electronics s.r.l. shall not be responsible for damage arising from
improper application or use.
2.6 Key
2.6.1 Glossary and terminology
Device: refers to the device specified in the Installation Manual paragraph
2.8 Device identifier.
General information 7
Programming manual
Left, right, behind, above, below: indications using the operator's
position in front of the mounted device as the reference point.
Pulse output: same as "monostable output"
Dialler (phone, SMS, digital):same as "communicator"
Qualified personnel: those persons whose training, expertise and
knowledge of the respective laws and bylaws regarding service conditions
and the prevention of accidents, are able to identify and avoid all possible
situations of danger.
Click on: click to select a specific item (from drop-down menu, options box,
graphic object, etc.).
Select: click on a video button.
2.6.2 Graphic key
Text in italics: indicates the title of a chapter, section, paragraph, table or
figure in this manual or other published reference.
<text>: editable space, for example #<CustomerCode># may become
#0001#.
[Uppercase letters] (e.g..[A]): indicate the device parts or video objects.
Note: The detached notes contain important information about
the respective text.
Attention: The attention prompts indicate that total or partial
disregard of the procedure could damage the
connected devices.
Danger: The danger warnings indicate that total or partial
disregard of the procedure could injure the operator
or persons in the vicinity.
8 Programming the SmartLink-GP
Programming manual
Chapter 3
Programming the SmartLink-GP
3.1 Introduction
The SmartLink-GP can be programmed to manage:
• Intrusion control
• SMS dialler
• Contact ID Dialler
• Remote appliance control
• Voice dialler (optional feature)
Note: If the SmartLink-GP is used as a reserve line generator, no
programming is required.
SmartLink-GP programming requirements:
• a portable computer for parameter downloading to the powered-up wall-
mounted device
• RS232 link cable
• SmartLeague software
3.2 Installing the SmartLeague software
3.2.1 Installing SmartLeague from the CD
If included in your purchase order, you will have the SmartLeague
Installation CD containing the software for the respective SmartLink-GP
firmware. Check the software version, refer to Help, About SmartLeague.
New versions of the SmartLeague software can be downloaded from the INIM
electronics Web address at www.inim.biz.
After installing the SmartLeague software, contact the Web address to find
out about new versions. Internet connection required.
Installation instructions
1. Insert the Installation CD into your service computer.
2. Select 'Computer Resources' on your desktop.
3. Find the CD unit, double click on the icon: the CD contents will be
displayed.
4. Double click on Setup.exe: the Welcome to the installation
program window appears.
5. Select 'Continue': the Folder selection window appears.
Programming the SmartLink-GP 9
Programming manual
Note: You should select the suggested folder.
6. Select 'Continue': file installation initializes, the progress bar will
indicate completion.
Note: Always complete installation, do not select Cancel during
the installation phase.
7. Once installation has been completed, the SmartLeague icon will appear
on your desktop (if requested by the user) and in the program
list:
3.2.2 Check for the availability of a new version
of the SmartLeague software.
8. Connect with us at www.inim.biz to find out about SmartLeague
software upgrades.
9. View the differences between the new version and the installed version.
10. Work carefully through the upgrade instructions.
3.2.3 Check for the availability of a new version
of the firmware.
11. Connect with us at www.inim.biz to find out about SmartLink-GP
firmware upgrades.
12. Work carefully through the download and installation instructions. All
upgrades come with the revised version of the manual.
3.3 SmartLeague software
SmartLeague is the SmartLink-GP configuring software. The program is
designed to run on your service computer and will allow you to program
most of the SmartLink-GP parameters without actually being connected to
the system.
Your service computer must be connected to the mounted powered-up
SmartLink-GP during the parameter downloading phase.
The connection cable must be long enough to reach the mounted device
without difficulty. Refer to the Installation Manual - paragraph 7.13
Connecting the RS232 PC serial link.
The parameter settings can be saved to the SmartLeague database and used
for service purposes or as a 'standard configuration' for other SmartLink-GP
devices.
During service sessions, you will be able to view and change the SmartLink-
GP parameter settings.
10 Programming the SmartLink-GP
Programming manual
3.3.1 General information
SmartLeague is the configuring software of the entire INIM electronics
product spectrum. You can configure numerous devices/systems on your
office service computer, regardless of the type of device/system.
You can configure a device on your service computer, then write the data to
the device EEPROM when you get to the customer's premises.
You can work on several parameter groups ('solutions') at the same time, for
example, you can copy a device/system configuration and download it to
another device/system of the same type. Each solution has its own
configuration file:
If you wish to create a 'solution', you must first select the device type and
model:
The start page of the SmartLeague software is connected to the INIM Web
providers, if you are connected to internet, it will show all the updated
information regarding software and firmware upgrades, revised manuals,
instruction inserts and newsletters, etc.
Altri manuali per SmartLink-G
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali INIM Electronics Sistema di conferenza
Manuali Sistema di conferenza popolari di altre marche
Kramer
Kramer VIA GO Manuale utente
AVT
AVT MAGIC AC1 Go Manuale utente
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manuale utente
Sony
Sony PCS-I150 Manuale utente
Middle Atlantic Products
Middle Atlantic Products VTC Series Manuale utente
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guida
