INIM Electronics SmartLink-G Manuale utente
SmartLink-G, SmartLink-GP
GSM Dialler
Installation
Manual
PATENT PENDING
0470
Installation manual
2
Copyright
The information contained in this document is the sole
property of INIM Electronics s.r.l. No part may be copied
without written authorization from INIM Electronics s.r.l.
All rights reserved.
Directive 1999/5/CE (R&TTE) compliance.
Hereby INIM Electronics s.r.l. declares that the
SmartLink-G and SmartLink-GP are in compliance with
the essential requirements and other relevant provisions
of Directive 1999/5/CE.
The full declarations of conformity of the above-
mentioned devices are available at URL:
www.inim.biz/dc.html.
3
Installation manual
Table of contents
Chapter 1 Introduction .................................5
1.1 Application and use 6
1.2 Other applications 7
Chapter 2 General information....................... 9
2.1 Documentation supplied 9
2.2 Manual 9
2.3 Addresses 9
2.4 Software information 9
2.5 Intellectual property rights 9
2.6 Key 10
2.7 Manufacturer's name and address 10
2.8 Device identifier 11
2.9 Warranty 11
2.10 Safety laws 11
Chapter 3 Device management.................... 13
3.1 Shipping 13
3.2 Environmental conditions 13
3.3 Unpacking the device 13
Chapter 4 Technical description ................... 15
4.1 Technical specifications 16
4.2 Reserve line electrical specifications 16
Chapter 5 Internal devices .......................... 17
5.1 Terminal board 17
5.2 Status LEDs 20
Chapter 6 Device features........................... 22
6.1 Intrusion control 23
6.2 Digital dialler (Contact ID) 23
6.3 SMS dialler 23
6.4 Voice dialler 23
6.5 Remote activation via SMS text message 23
6.6 Remote control via DTMF 24
6.7 Caller ID 24
Chapter 7 Installing the SmartLink-GP.......... 25
7.1 Wall mounting 25
7.2 Mounting the antenna 26
7.3 Mounting the remote antenna 27
7.4 Connecting the land line (PSTN) 28
4
Installation manual
7.5 Connecting telephone devices 28
7.6 Earth connection 28
7.7 Connecting the tamper microswitch 28
7.8 Connecting the IN&OUT terminals 28
7.9 Connecting the SmartLogos60 (accessory
item) 29
7.10 Inserting the SIM card 29
7.11 Connecting the DC power 29
7.12 Connecting an ancillary power supply 30
7.13 Connecting the RS232 PC serial link 30
7.14 DC power 32
7.15 Closing the casing 32
7.16 Initializing phase 32
7.17 Test 32
Appendix A Features not managed by the Smart-
Link-G model ..............................33
Appendix B Order code .................................34
Introduction 5
Installation Manual
Chapter 1
Introduction
SmartLink is available in the following models:
• SmartLink-GP
•SmartLink-G
Besides the features of the SmartLink-G model, the SmartLink-GP model
also provides the following advanced features:
1. intrusion control
2. voice dialler (requires SmartLogos60 accessory board)
3. PSTN line call management
The Smartlink-G model does not manage these features.
This manual describes the Smartlink-GP features and programming process.
SmartLink-G users can skip the sections which refer to the advanced
features.
Refer to Appendix A for a detailed list of the extra features provided by
Smartlink-GP and respective programming process.
6Introduction
Installation Manual
1.1 Application and use
The SmartLink-GP device described in this manual is a reserve telephone line
generator.
Figure 1 - Reserve telephone line
In the event of land line trouble (PSTN line down) the Smartlink-GP will
switch all calls to the GSM network (simulated-line mode). This operating
mode will not affect any of the connected devices. During simulated-line
mode, the SmartLink-GP will check the land-line for restoral at regular
intervals. If the land line restores during GSM line-free status, the system
will switch back to the land line. Otherwise it will switch back when the
ongoing call ends.
GSM network
Introduction 7
Installation Manual
The Smartlink-GP provides a series of optional features, some of which
require accessory boards:
• Intrusion control
• Operations manager (e.g. sends calls, output commands) generated by
internal events (e.g. low battery) or external events (e.g. input status
changes, received calls, received SMS text messages)
• Output status enquiry and commands via SMS
• Output status enquiry and commands via DTMF
• Caller ID Output commands
• Digital dialler (Contact ID)
• SMS dialler
• Voice dialler (optional feature)
1.2 Other applications
The diagrams on the following pages illustrate some of the vast range of
SmartLink-GP applications.
Figure 2 - Output status enquiry and commands via DTMF
and SMS text messages — PSTN (land line) or GSM network
8Introduction
Installation Manual
Figure 3 - Intrusion panel feature - digital telephone dialler
(Contact ID) - land line (PSTN) and GSM network
Figure 4 - Operations manager in response to external events
- SMS dialler- Voice dialler (optional feature)
GSM network GSM network
Detector
Voice message
GSM
network
General information 9
Installation Manual
Chapter 2
General information
2.1 Documentation supplied
• Installation manual (this manual)
• Programming manual
If you require the Programming manual, please contact INIM Electronics
s.r.l. and specify the order code shown in Appendix B .
2.2 Manual
Title: SmartLink-G and Smartlink-GP Installation Manual
• Edition, Issue: 2.10
• Month and Year of issue: October 2012
• Order code: DCMIINE0SLINK
2.3 Addresses
• Installer
• Technical assistance
2.4 Software information
• Smartleague software version: 3.x.x
• Firmware version : 2.x.x
2.5 Intellectual property rights
The information contained in this document is private property. All rights
reserved.
No part of this document may be copied or reproduced unless expressly
authorized in writing by INIM Electronics, in particular the parts regarding
the device specified in 2.8 Device identifier.
INIM Electronics s.r.l. shall not be responsible for damage arising from
improper application or use.
10 General information
Installation Manual
2.6 Key
2.6.1 Glossary and terminology
Device: refers to the device defined in 2.8 Device identifier.
Left, right, behind, above, below: indications using the operator’s position
in front of the mounted device as the reference point.
Pulse output: same as "monostable output".
Dialler (telephone, SMS, digital):same as "communicator".
Qualified personnel: those persons whose training, expertise and
knowledge of the respective laws and bylaws regarding service conditions
and the prevention of accidents, are able to identify and avoid all possible
situations of danger.
2.6.2 Graphic conventions
Text in italics: indicates the title of a chapter, section, paragraph, table or
figure in this manual or other published reference.
[Uppercase letters] (e.g.[A]): indicate the device parts.
Note: The detached notes contain important information relating
to the respective text.
Attention: The attention prompts indicate that total or partial
disregard of the procedure could damage the
connected devices.
Danger: The danger warnings indicate that total or partial
disregard of the procedure could injure the operator
or persons in the vicinity.
2.7 Manufacturer's name and address
INIM Electronics s.r.l.
Via Fosso Antico, Centobuchi
63033 Monteprandone (AP) - Italy
Tel: +39 0735 70 50 07
Fax: +39 0735 70 49 12
Altri manuali per SmartLink-G
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali INIM Electronics Sistema di conferenza
Manuali Sistema di conferenza popolari di altre marche
Kramer
Kramer VIA GO Manuale utente
AVT
AVT MAGIC AC1 Go Manuale utente
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manuale utente
Sony
Sony PCS-I150 Manuale utente
Middle Atlantic Products
Middle Atlantic Products VTC Series Manuale utente
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guida
