InPlay NanoBeacon IN100 Manuale utente
Specifications and information are subject to change without notice.
InPlay NanoBeacon™
IN100 Development Kit
User Manual
1 / 11
InPlay NanoBeacon™ IN100 Development Kit user manual
Contents
About Documentation ................................................................................... 3
1. General Description ...............................................................................4
2. Hardware Description ............................................................................ 6
3. Schematic .............................................................................................10
4. Revision History .................................................................................... 11
5. Legal Disclaimer.................................................................................... 11
2 / 11
InPlay NanoBeacon™ IN100 Development Kit user manual
List of Figures
Figure 1：Development Kit............................................................................................... 4
Figure 2：Development board.......................................................................................... 5
Figure 3：Programmer board........................................................................................... 5
Figure 4：Development board.......................................................................................... 6
Figure 5：Programmer board........................................................................................... 9
Figure 6：Development Kit schematic ............................................................................10
3 / 11
InPlay NanoBeacon™ IN100 Development Kit user manual
About Documentation
Product status
Document content
Data status
In development
Target specification / MRD
Initial release
Engineering Document
Main functions and features
description
Preliminary version
Official release
document
Description of all functional features
Subject to revision and
updates
This document applies to the following products:
Part number
Applicable products
Document status
IN1BN-DKC0-100-C0
IN100-D1-R-RC0I
Engineering sample
IN100-Q1-R-RC0I
In development
IN100-D1-R-RC0F
Engineering sample
IN100-Q1-R-RC0F
In development
Document name
InPlay NanoBeacon™ IN100
Development Kit user manual
Part number
IN1BN-DKC0-100-C0
Control number
IN1IDOC-HW-IN1BN-EN-V1_01
External user
Revision
V1.01
4 / 11
InPlay NanoBeacon™ IN100 Development Kit user manual
1. General Description
IN1BN-DKC0-100-C0 is an InPlay NanoBeaconTM development kit that
includes three IN100 development boards and one programmer board.
The development kit provides all the I/Os available on IN100 (QFN18
package) that allow users to easily connect peripheral devices such as
sensors, and by connecting the RF cables using SMA, users can
evaluate the RF performance more accurately. In addition, an external
power supply can be selected to provide a wide range of voltages for
the IN100 device or system evaluation.
A kit contains three development boards and one programmer board
as shown in Figure 1.
Figure 1：Development Kit
5 / 11
InPlay NanoBeacon™ IN100 Development Kit user manual
Development Board
⚫NanoBeaconTM IN100 SoC device
⚫3.5mm SMA male RF connector
⚫Device I/O pins
⚫Reset button
⚫CR1220 coin cell battery socket
⚫Power supply source selection switch : On-board coin cell Battery /
External power supply / Programmer board power supply
⚫System current measurement jumper provision
⚫Programming interface female connector
Programmer Board
⚫Programming interface male connector
⚫OTP (eFuse) memory programming power switch
⚫Programmer board output power selection switch : 1.8V / 3.3V / No
connect
⚫OTP memory (eFuse) burning LED indicator
⚫On-board USB to UART convertor
⚫Micro USB female connector
Figure 2：Development board
Figure 3：Programmer board
6 / 11
InPlay NanoBeacon™ IN100 Development Kit user manual
2. Hardware Description
Figure 4：Development board
Development board Connectors/Pins/Jumpers/Button Definition
Designator
Function
Description
J1
Connector
(development
board)
Pin #
Pin name
Description
1
VDDQ
OTP (eFuse) memory programming power pin
2
MGPIO7
IN100 mixed-signal GPIO
3
VBAT
System power supply, connected to the VCC pin of the
IN100 through J8
4
VBAT
System power supply, connected to the VCC pin of the
IN100 through J8
5
GND
Ground
6
GND
Ground
7
GPIO1
IN100 digital GPIO, Default is IN100 UART_TX
8
MGPIO5
IN100 mixed-signal GPIO
9
GPIO0
IN100 digital GPIO, Default is IN100 UART_RX
10
MGPIO4
IN100 mixed-signal GPIO
7 / 11
InPlay NanoBeacon™ IN100 Development Kit user manual
Designator
Function
Description
J2
Connector
(programmer
board)
Pin #
Pin name
Description
1
NC
No connect
2
VDDQ
OTP (eFuse) memory programming power pin
Power On/Off controlled by S1
3
PWR
Power supply, controlled by SW1
4
PWR
Power supply, controlled by SW1
5
GND
Ground
6
GND
Ground
7
NC
No connect
8
UART_RX
UART interface, connect to IN100 UART_TX
9
NC
No connection
10
UART _TX
UART interface, connect to IN100 UART_RX
J3
Connector for IOs
and power
Pin #
Pin name
Description
1
Reset
Connect to the Chip_EN pin of IN100 and pull low to
disable the chip, pull high to enable the chip
2
VBAT
System power supply, connect to IN100 VCC pin through
J8
3
MGPIO7
IN100 mixed-signal GPIO
4
MGPIO6
IN100 mixed-signal GPIO
5
MGPIO5
IN100 mixed-signal GPIO
6
GND
Ground
7
SW0
IN100 built-in load switch for power supply
8
SW1
IN100 built-in load switch for grounding
J4
Connector for IOs
and power
Pin #
Pin name
Description
1
VDDQ
OTP (eFuse) memory programming power pin
2
MGPIO4
IN100 mixed-signal GPIO
3
GPIO3
IN100 digital signal GPIO
4
GPIO2
IN100 digital signal GPIO
5
GND
Ground
6
VBAT
System power supply, connected to the VCC pin of the
IN100 through J8
7
GPIO0
IN100 digital GPIO, Default is IN100 UART_RX
8
GPIO1
IN100 digital GPIO, Default is IN100 UART_TX
8 / 11
InPlay NanoBeacon™ IN100 Development Kit user manual
Designator
Function
Description
J5
External power
supply
External power supply ( 1.1~3.6V input).
When this power supply is available, keep no coin cell
battery installed and switch the programmer board SW1 to
OFF.
J8
Current
measurement
- For normal operation, a jumper needs to be installed
- For current measurement
•Remove the jumper J8 on the board
•Power pin 1 (VCC) of J8 with an external power supply
with an ammeter. Initially, set the voltage same as
the voltage presented on J8 pin 2 (VBAT)
•Press the K1 button to reset the device and run the
user configuration in RAM (refer to the "Run in RAM"
operation in the NanoBeaconTM Configuration Tool
User Manual for details)
•Disconnect the programmer board from the
development board
•Set the external power supply to the voltage at which
you want to measure the current, and then measure
the current.
J9
RF TX output
connector
The male 3.5mm SMA RF connector for connecting an
external antenna ( Note: antenna is not provided in the kit)
P1
Chip_EN
- Chip_EN ON: Connect pin 1 and 2. This is to enable the
device.
- Chip_EN OFF: Connect pin 2 and 3. This is to disable the
device.
K1
Chip reset
Chip reset button
9 / 11
InPlay NanoBeacon™ IN100 Development Kit user manual
Figure 5：Programmer board
Programmer board Connectors/Pins/Jumpers/Button Definition
Designator
Function
Description
J6, J7
PC UART interface
jumpers
The UART between the device (IN100) and PC is disconnected
when no jumpers are installed.
J10
USB interface
Micro USB female connector for connecting with a PC
S1
OTP ON/OFF
OTP memory power supply switch.
- Switch On: eFuse (OTP) memory programming is enabled, J2
pin2(FUSE) output 3.3V and connected to the device’s (IN100)
VDDQ.
- Switch OFF: eFuse (OTP) memory programming is disabled.
J2 pin2 will be grounded and connected to VDDQ of the device
(IN100).
SW1
Power supply
source select
switch
-1.8V: 1.8V output for the development board
-3.3V: 3.3V output for the development board
-OFF: No power is provided by the programmer board. The
power is provided by the development board itself.
Indice
Altri manuali InPlay Microcontrollore
Manuali Microcontrollore popolari di altre marche
AMS
AMS AS7261 Demo Kit Manuale utente
Novatek
Novatek NT6861 Manuale utente
Espressif Systems
Espressif Systems ESP8266 SDK Guida all'installazione
Nuvoton
Nuvoton ISD61S00 ChipCorder Guida
STMicrolectronics
STMicrolectronics ST7 Assembler Linker Manuale utente
Texas Instruments
Texas Instruments Chipcon CC2420DK Manuale utente
Lantronix
Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente
NEC
NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento
Mikroe
Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento
Intel
Intel Agilex Manuale utente
Cypress
Cypress CY4607 HX2VL Manuale utente
DIGITAL-LOGIC
DIGITAL-LOGIC MICROSPACE Manuale utente
Texas Instruments
Texas Instruments TMS320F2837 D Series Manuale utente
CYPRES
CYPRES CY14NVSRAMKIT-001 Manuale utente
Texas Instruments
Texas Instruments INA-DUAL-2AMP-EVM Manuale utente
Espressif Systems
Espressif Systems ESP8266EX Istruzioni operative
Abov
Abov AC33M8128L Manuale utente
Laird
Laird BL654PA Manuale utente