Intel 5000 Series Manuale utente

Intel®5000 Sequence Processor

Integration

Warning, Important Safety Instructions

System power on/off: The power button DOES NOT turn off the system AC power. To remove power

from system, you must unplug the AC power cord from the wall outlet. Make sure the AC power cord is

unplugged before you open the chassis, add, or remove any components.

Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on power,

telephone, and communication cables. Turn off the server workstation and disconnect the power cord,

telecommunications systems, networks, and modems attached to the server workstation before opening

it. Otherwise, personal injury or equipment damage can result.

Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards, and other

parts. We recommend that you perform all procedures in this chapter only at an ESD workstation. If one

is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis

ground any unpainted metal surface on your server workstation when handling parts.

ESD and handling boards: Always handle boards carefully. They can be extremely sensitive to ESD.

Hold boards only by their edges. After removing a board from its protective wrapper or from the server

workstation , place the board component side up on a grounded, static free surface. Use a conductive

foam pad if available but not the board wrapper. Do not slide board over any surface.

Installing the Processor

Note:

• Do not touch the contacts on either the processor or the processor socket.

• Do not force the processor socket into place. When correctly aligned, the socket will easily drop

into place.

To install a processor, follow these instructions:

1. Observe safety and ESD precautions.

2. Turn off all peripheral devices connected to the server. Turn off the server.

3. Disconnect the AC power cord from the server.

4. Remove the chassis cover. See the documentation that came with your chassis for instructions

on removing the cover.

5. Locate the processor sockets (see Figure 1).

Figure 1. Example: Locating Processor Sockets.

Note: Consult Your Board Documentation for Proper Socket Location

6. Disconnect and remove any components necessary to access the processor sockets. See the

documentation that came with your chassis for instructions on removing chassis components.

7. Push down on the lever attached to the processor socket. While holding the lever down, pull it

towards the center of the board to disengage the lever from the hook. Fully open the lever. See

Figure 2.

Figure 2. Opening Processor Socket Lever

8. Push down on the rear tab of the load plate to swing the front of the load plate up slightly. Fully

open the load plate. See Figure 3.

Figure 3. Opening Load Plate

9. If the protective cover is attached from the load plate, remove it and store it for future use. See

Figure 4.

Figure 4. Removing Protective Cover from Load Plate

10. Remove the processor from the box and remove the protective shipping cover.

11. Set the processor in the socket with the processor cutouts matching the processor socket

notches. See Figure 5.

Figure 5. Setting Processor in Place

12. Close the load plate.

13. Close the socket lever. Push downward on the socket lever while pushing it toward the center of

the processor socket to engage it under the hook on the processor socket.

Installing the Heat Sink(s)

Note: The heat sink has thermal interface material (TIM) located on the bottom of it. Use

caution when handling the heat sink so you do not damage the TIM.

Each processor requires a heat sink. Depending on your chassis, you may need to use

either a active (Figure 6) or an passive heat sink (Figure 7). An active heat sink has a fan

attached to the top of it and a cable that needs to be connected to the server board.

AF000099

Figure 6. Active Heat Sink (Cable Not Shown)

Use the following steps to install a heat sink.

1. Set the heat sink over the processor, lining up the four captive screws with the four posts

surrounding the processor.

2. Loosely screw in the captive screws on the heat sink corners in the order shown by Figure 7.

Do not fully tighten one screw before loosely attaching the others.

3. In the same order, gradually and equally tighten each captive screw until each is firmly

tightened. Do not fully tighten one screw at a time.

Figure 7. Installing Heat Sink (Passive Heat Sink Shown)

4. Active heat sink only: Connect the heat sink cable to the server board. Reference you board

documentation for proper fan header location.

5. Reinstall and reconnect any parts you removed or disconnected to reach the processor sockets.

See the documentation that came with your chassis for instructions on installing chassis

components.

6. Replace the chassis cover and reconnect the AC power cord. See the documentation that came

with your chassis for instructions on installing the cover.

Altri manuali per 5000 Series

Indice

Altri manuali Intel Hardware per computer

Intel

Intel G34920-002 Manuale utente

Intel

Intel AXXRAKSAS2 Manuale utente

Intel

Intel AXXROMBSASMR Manuale di installazione

Intel

Intel RS2WG160 Guida all'installazione

Intel

Intel Xeon Phi Processor x200 Guida

Intel

Intel I5-520E - ADDENDUM Manuale utente

Intel

Intel i960 Series Guida

Intel

Intel X5550 - Quad Core Xeon Guida

Intel

Intel AXXRMS2AF080 Manuale di installazione

Intel

Intel I5 3570K Manuale utente

Intel

Intel Braswell Series Manuale utente

Intel

Intel NetBurst Manuale utente

Intel

Intel 855GME Guida

Intel

Intel CORE 2 DUO MOBILE - THERMAL DESIGN GUIDE... Guida

Intel

Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1... Manuale utente

Intel

Intel D815EEA2 Manuale utente

Intel

Intel SL3VS - Celeron 633 MHz Processor Manuale utente

Intel

Intel SRCS14L - RAID Controller Manuale utente

Intel

Intel CMCN1CC Guida rapida alla configurazione

Intel

Intel RS25AB080 Manuale utente

Intel

Intel BX80623G530 Manuale utente

Intel

Intel E7500 Guida

Intel

Intel BX80616I3540 Guida

Intel

Intel P4000IP Series Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

Advantech

Advantech ASMB-935 Series Manuale utente

Jupiter

Jupiter RAM PACK Manuale utente