Intelix INT-BSR4K-H2 Manuale utente

11675 Ridgeline Drive
Colorado Springs, CO
80918
Rev 180717 Phone: 719-260-0061
Toll-Free: 800-530-8998
Fax: 719-260-0075
INT-BSR4K-H2 Owners Manual

INT-BSR4K-H2 Owners Manual
2

INT-BSR4K-H2 Owners Manual
3
Important Safety Instrucons
»Please completely read and verify you understand all instrucons in this manual before operang this equipment.
»Keep these instrucons in a safe, accessible place for future reference.
»Heed all warnings.
»Follow all instrucons.
»Do not use this apparatus near water.
»Clean only with a dry cloth.
»Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers)
that produce heat.
»Use only accessories specied or recommended by Intelix.
»Explanaon of graphical symbols:
◊ Lightning bolt/ash symbol: the lightning bolt/ash and arrowhead within an equilateral triangle
symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the
product enclosure which may be of sucient magnitude to constute a risk of shock to a person or
persons.
◊ Exclamaon point symbol: the exclamaon point within an equilateral triangle symbol is intended
to alert the user to the presence of important operang and maintenance (servicing) instrucons
in the literature accompanying the product.
»WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.
»Use the mains plug to disconnect the apparatus from the mains.
»THE MAINS PLUG OF THE POWER CORD MUST REMAIN READILY ACCESSIBLE.
»Do not defeat the safety purpose polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of
your obsolete outlet. Cauon! To reduce the risk of electrical shock, grounding of the center pin of this plug must be
maintained.
»Protect the power cord from being walked on or pinched parcularly at the plugs, convenience receptacles, and the
point where they exit from the apparatus.
»Do not block the air venlaon openings. Only mount the equipment per Intelix’s instrucons.
»Use only with the cart, stand, table, or rack specied by Intelix or sold with the equipment. When/if a
cart is used, use cauon when moving the cart/equipment combinaon to avoid injury from p-over.
»Unplug this apparatus during lightning storms or when unused for long periods of me.
»Cauon! Shock Hazard. Do not open the unit.
»Refer to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.

INT-BSR4K-H2 Owners Manual
4
Table of Contents
Product Overview���������������������������������������������������������������������������������������������������������������5
Package Contents���������������������������������������������������������������������������������������������������������������5
Front and Rear Panel View�������������������������������������������������������������������������������������������������6
Installaon Instrucons �����������������������������������������������������������������������������������������������������7
Quick Start ��������������������������������������������������������������������������������������������������������������������7
Mount the Switcher / Extender������������������������������������������������������������������������������������7
Connect Compable HDBaseT Transmier������������������������������������������������������������������7
Connecng a Display ����������������������������������������������������������������������������������������������������8
HDMI Output �����������������������������������������������������������������������������������������������������������8
Connect Audio Output ��������������������������������������������������������������������������������������������������8
Connecng Control �������������������������������������������������������������������������������������������������������8
RS232 Control Wiring ����������������������������������������������������������������������������������������������8
Passing IR Signals ����������������������������������������������������������������������������������������������������9
Apply Power ������������������������������������������������������������������������������������������������������������������9
Applicaon Diagram ��������������������������������������������������������������������������������������������������������10
RS232 and TCP/IP Control ������������������������������������������������������������������������������������������������11
RS232 Mode Funcons �����������������������������������������������������������������������������������������������11
Output Scaler Sengs ������������������������������������������������������������������������������������������������12
EDID Input Sengs �����������������������������������������������������������������������������������������������������13
CEC to Display Commands������������������������������������������������������������������������������������������13
RS232 to Display Commands��������������������������������������������������������������������������������������14
RS232 to Display Commands (connued) ������������������������������������������������������������������15
De-embedded Audio Output Sengs�������������������������������������������������������������������������16
IP Addressing Commands�������������������������������������������������������������������������������������������16
Miscellaneous Commands������������������������������������������������������������������������������������������17
Technical Specicaons ���������������������������������������������������������������������������������������������������18

INT-BSR4K-H2 Owners Manual
5
The INT-BSR4K-H2 is an HDMI 2.0 and HDCP 2.2 compliant HDBaseT scaling 4K receiver
that distributes uncompressed 4K@60Hz UHD video, digital coax / analog stereo audio,
Ethernet, RS232 and bi-direconal IR up to 100m/330 over a single category cable.
The INT-BSR4K-H2 can be controlled by telnet or RS232 but also can also store and pass
display commands via RS232 as well as generate CEC display ON and OFF commands.
The two-port network switch on the INT-BSR4K-H2 allows a second device to share the
100BaseT Ethernet pass-through connecon without adding addional hardware to the
installaon. The INT-BSR4K-H2 requires local power, however it can provide power to a
compable Intelix HDBaseT transmier.
The INT-BSR4K-H2 is compable with all Intelix HDBaseT product oerings and any
product that meets the HDBaseT specicaons.
Product Overview
Package Contents
• INT-BSR4K-H2 HDBaseT Scaling Receiver
• Quick Install Guide
• DC12V 3A power supply with US, UK, EU and AU power cords
• (1) IR Emier
• (1) IR Receiver
• (2) 3.5mm 3 pin phoenix male connectors
• (2) Mounng Brackets

INT-BSR4K-H2 Owners Manual
6
Front and Rear Panel View
1
2 3 4 5 6 7 8 9 10
11 12
1. 12V DC - Locking power port to connect DC12V power adapter
2. ETHERNET 1 - Ethernet Port 1
3. ETHERNET 2- Ethernet Port 2
4. HDBT IN - HDBaseT input to connect to HDBaseT output from transmier via category cable
5. IR IN- IR Input to connect to IR receiver
6. IR OUT - IR Output to connect to IR emier
7. HDMI OUT - HDMI output for display connecvity
8. S/PDIF OUT - Digital (S/PDIF) Coax Audio Output
9. AUDIO OUT - Analog Audio Output
10. RS232 - Serial control port for display control / 3rd party control
11. POWER STATUS LED - When solid, the transmier is receiving power
12. STATUS LEDS
• SCALER- When blinking slowly, the scalar chip is working properly
• STATUS- When blinking slowly, the transmier is working properly
• HDCP - When solid, HDCP content is being transmied; when blinking NON HDCP content is being
transmied; when o there is no audio or video data transmied
• LINK - When solid, the link between transmier and receiver is normal. When blinking or o the link
between transmier and receiver is not operable

INT-BSR4K-H2 Owners Manual
7
Installaon Instrucons
Quick Start
Mount the Switcher / Extender
1. Mount the switcher / extender set
2. Connect compable HDBaseT transmier
3. Connect display
4. Connect audio output (oponal)
5. Connect control (oponal)
6. Apply power
At least 2 inches of free air space is required on both sides of the INT-BSR4K-H2 for proper side venlaon.
Avoid mounng the INT-BSR4K-H2 near a power amplier or any other source of signicant heat.
Aach the supplied mounng brackets to the sides of the receiver. Once the rails are installed the receiver can
be mounted in an A/V enclosure or on the wall behind a display or above a projector.
TIA/EIA-568B
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
1 8
Connect the INT-BSR4K-H2 HDBaseT receiver to a compable Intelix HDBaseT transmier using a Category
cable.
Twisted Pair Wiring
Use TIA/EIA-568B wiring for Category 6
connecon between the transmier and
receiver
To ensure proper performance of the INT-BSR4K-H2, it is recommended that you use solid
core shielded Category 6 F/UTP cabling at a minimum. Category 5e F/UTP may perform well
but may not support power over HDBaseT reliably.
For opmized performance use the following Liberty Wire and Cable branded cabling;
Category 6 plenum; 24-4P-P-L6SH
Category 6A plenum; 24-4P-P-L6ASH
Category 6 NON-plenum; 24-4P-L6SH
Category 6A NON -plenum; 24-4P-L6ASH
When using shielded category cabling ALWAYS...
....use shielded connectors
....properly ground the category cable
Connect Compable HDBaseT Transmier

INT-BSR4K-H2 Owners Manual
8
L
R
L
R
AUDIO
SOURCE INT-BSR4K-H2
Connecng a Display
HDMI Output
Connect the display devices to HDMI output on the receiver using an HDMI cable that is less than or equal to
5 meters in length.
Connect Audio Output
Insert the removable 3-pin phoenix connector block to the audio output. The INT-BSR4K-H2 supports a stereo
unbalanced output
Connecng Control
RS232 Control Wiring
Connect the INT-BSR4K-H2 receivers LAN port to an Ethernet control network for telnet control.
Connect the DL-SE3H1V-C RS232 port on the receiver for serial control.
Note: The INT-BSR4K-H2 RS232 port can either be used with a control system for serial
control or can be connected to an external display for ON/OFF display control using
telnet control.
For complete list of control commands see pg11 RS232 and TCP/IP Control
Tx RXD
GND
Rx TXD
INT-BSR4K-H2 Controller or
Device
Connect the controller or device RX signal to TX port of the INT-BSR4K-H2 receiver. Then connect the controller or
device TX signal to the RX port on the INT-BSR4K-H2 receiver.

INT-BSR4K-H2 Owners Manual
9
Apply Power
Plug the power supply into the power input port on the rear of the INT-BSR4K-H2 receiver Twist the locking ring
clockwise to prevent accidental disconnecon of power.
Note: The INT-BSR4K-H2 scaling receiver can provide power to a compable Intelix transmier via HDBaseT,
however a compable Intelix HDBaseT transmier (including HDBaseT matrix switchers) cannot provide power
to the INT-BSR4K-H2.
The INT-BSR4K-H2 is capable of passing IR signals between 33 and 55 KHz. To prevent damage to any of the electronics,
the extenders should be powered o while inserng or removing any IR components. Inserng an IR transmier into the
IR IN port may damage the IR circuit for that extender.
IR OUT: The IR transmier (IR emier) must be plugged into the IR OUT port.
IR IN: The IR receiver (IR eye) must be plugged into the IR IN port.
Passing IR Signals

INT-BSR4K-H2 Owners Manual
10
MEDIA PLAYER
IR REMOTE 1
IR REMOTE 2
CONTROL SYSTEM
HDMI
CATx
AUDIO
RS232
IR
AUDIO AMP
PROJECTOR
up to 100m / 330’
Intelix INT-HDX100-TX
(NOT INCLUDED)
Applicaon Diagram
Indice
Altri manuali Intelix Ricevitore

Intelix
Intelix INT-HDX100-RXWP Manuale utente

Intelix
Intelix DIGI-HDMI-HR-R Manuale utente

Intelix
Intelix NT-BSR4K-H2 Manuale utente

Intelix
Intelix DIGI-HDMI-HR Manuale utente

Intelix
Intelix AvoCat Series Manuale utente

Intelix
Intelix SKYPLAY-DFS Series Istruzioni operative

Intelix
Intelix DIGI-VGASD2-S Manuale utente

Intelix
Intelix SKYPLAY-MX Istruzioni operative

Intelix
Intelix DIGI-DVI-F Manuale utente

Intelix
Intelix DIGI-HD-UHR2-R Manuale utente

















