Intelix S-V1AR Manuale utente
Intelix S-V1AR
Installation Manual
Introduction
Ideal for transmitting composite video extended distances over
twisted pair cable, the Intelix S-V1AR receives signals from remote
Intelix baluns up to 4,000 feet away. The unit features screw
terminal connectors for the twisted pair input and two BNC
connectors for the analog video output, thereby allowing two devices
to simultaneously receive the picture. Each output video channel is
adjustable with gain and skew switches.
The S-V1AR is compatible with all baseband signals, including
PAL, NTSC, and SECAM, and features built-in transient protection
and exceptional interference rejection. The unit includes a 12V
power supply.
When signal quality matters, choose Intelix.
Installation
1. Power off the source and destination devices which will be connected to the
baluns.
2. Verify the modular outlets and cross connects to which you will connect the S-
V1AR are configured properly and labeled appropriately to identify the circuit.
3. Verify the desired twisted pairs are not being used for other LAN or telephone
equipment.
4. Connect the S-V1AR to the video port of the destination equipment. If desired,
connect the second output to a secondary destination device.
5. Connect one end of the twisted pair cable to the S-V1AR balun.
6. Connect a compatible transmit balun to the video port on the source equipment.
7. Connect the other end of the twisted pair cable to the second balun. The twisted
pair pinout on both the send and receive baluns should match.
8. Connect the 12V power supply to the S-V1AR. Verify the power LED is
illuminated.
9. Power on the source and destination equipment.
10. Verify picture quality. If necessary, adjust the Distance Adjust dipswitches on the
bottom of the unit.
Caution: Do not attempt to disassemble or alter the balun housin
g
. There are no
user-serviceable parts inside the unit. Doing so will void your warranty.
Caution: Do not connect the balun to a telecommunication outlet wired to
unrelated equipment. Doing so may damage the unit or any connected equipment.
Ensure all connected twisted pair cabling is straight-through (point-to-point).
Caution: To minimize the possibilit
y
of equipment dama
g
e from electrostatic
discharge (ESD), all source and destination equipment must be powered off durin
g
installation. This includes signal extenders, splitters, and switches.
Note: For
y
our convenience, it is recommended that
y
ou uniquel
y
mark the ends
of the twisted pair cable before pulling them through a wall or conduit.
Troubleshooting
Symptom Probable Causes Possible Solutions
Image not stable Defective link or
equipment
Verify source and destination equipment and
cabling
Unusual colors Reversed polarity Verify the pinout on both the send and
receive baluns match. Try swapping pairs.
Smearing or weak
video contrast
Exceeded cable
distance
Verify cable grade and total cabling distance
Horizontal bars
moving upward in
background
Ground loop
problem
Verify the source and destination equipment
are at the same ground potential. Ground the
source and destination equipment.
Shaking image Ground loop
problem
Verify the source and destination equipment
are at the same ground potential. Ground the
source and destination equipment.
Variance in hue EMI interference Identify possible radiating frequency sources
and isolate them from the cabling. Use
shielded twisted pair cabling.
Background
pattern
EMI interference Identify possible radiating frequency sources
and isolate them from the cabling. Use
shielded twisted pair cabling.
Technical Specifications
Maximum Distance Fully active system: 4,000 feet
Passive system: 2,000 feet
Compatible Power
Supply
12 – 40 VDC
9 – 24 VAC
Compatible Active
Intelix Baluns
S-V1AT
Compatible Passive
Intelix Baluns
S-V1ST
S-V1P-T
S-V1CP
Bandwidth DC to 8 MHz
Maximum Input 1.1 Vp-p, 75 ohms
Insertion Loss Less than 2 dB over the frequency range
Return Loss Greater than 15 dB over the frequency range
Protection 2KV (10/700 µs)
IEC 6100-4-5/1955 GB/T 1726, 5-1999
Over-current Protection 100 mA max
Cable Unshielded Cat 5, Cat 5e, Cat 6 or better
Temperature Operating: 0 to 55 C.
Storage: -20 to 85 C.
Humidity: up to 95% non-condensing
Warranty 2 years
Order Information S-V1AR: one balun and one power supply
Distances and picture quality may be affected by cable grade, cable quality, source and destination
equipment, RF and electrical interference, and cable patches. Intelix specifications are based on
straight-through cabling with standard-grade Cat 5.
Intelix
2222 Pleasant View Road
Middleton, WI 53562
608-831-0880 | phone
866-4-MATMIX | toll-free
608-831-1833 | fax
www.intelix.com
Altri manuali Intelix Trasmettitore
Intelix
Intelix AVO-VGA2-WP Manuale utente
Intelix
Intelix DIGI?HD?UHR2 Manuale di istruzioni
Intelix
Intelix DIGI-VGASD2-T8 Manuale utente
Intelix
Intelix INT-HDX100-RXWP Manuale utente
Intelix
Intelix Power Supply IX-DIGI1 Manuale utente
Intelix
Intelix AVO-V3AD-WP110-UK Manuale utente
Intelix
Intelix V1-CV Manuale utente
Intelix
Intelix DigiCat Series Manuale utente
Intelix
Intelix AVO-V2A2-F Manuale utente
Intelix
Intelix DIGI-HD-IR2 Manuale utente
Intelix
Intelix DIGI-V3SD-S Manuale utente
Intelix
Intelix AVO-V3PT-F Manuale utente
Intelix
Intelix AVO-V1-WP Manuale utente
Intelix
Intelix Intelix DIGI-VGASD-R Manuale utente
Intelix
Intelix DIGI‐HD‐IR2 Manuale utente
Intelix
Intelix DIGI-HD-IR3-WP Manuale utente
Intelix
Intelix AvoCat AVO-A4 Series Manuale utente
Intelix
Intelix AVOCat AVO-A2-WP-F Manuale utente
Intelix
Intelix AVO-VGA Manuale utente
Intelix
Intelix AVO-A4-WP110-EU Manuale utente
