Interlogix Sentrol DV1201A Manuale utente
- 1 -
DV1201A & DV1221A
Seismic Detectors Installation Manual
Figure 2: Two ways to test the seismic detectors
1/2. 12 Vdc 7. Common (C)
3. LED indication 8/9. Tamper
4. Integrator level 10. Test control
5. Normaly Closed (NC) 11. Spare
6. Normaly Open (NO)
Test disabled (ex-factory setting)
Internal test of detector’s electronics =
Position jumper between 1 and 2 .
Function test of the detector and its physical contact
with the protected object = Position connector from
test transmitter DV1215A between 2 and 3.
Connecting terminal 10 to 0 V activates both tests.
1. Cover
2. Cover screw
3. Base plate
4. Mounting holes
5. Clamp
6. Area for mounting the
DV1215A test transmitter
7. Potentiometer for adjusting
the detector’s sensitivity
8. Connection block
9. Anti-tamper micro-switch
10. Mounting plate DV1202A
11. Fixing bolt
12. Expander bolt
13. Test transmitter DV1215A
Figure 3: General characteristics of the DV1201A / DV1221A
Using the mounting plate DV1202A as a template
A. Holes for DV1201A / DV1221A
B. Hole for expansion plug or recess mounting box
C. Template and mounting holes for test transmitter DV1215A
D. Holes for accessories.
Figure 4: Mounting the detector directly on a metal surface without using a mounting plate
Figure 1: Wiring diagram
Sentrol
24-04-'02
Manual DV1201A / DV1221A 14 999-
5620
Form: Letter (bookshape)
Formaat: Letter (boekvorm)
A4
G. Manders
110-01
White paper: 70gr/m² progresso; overprint black. If P.O.D.: use 80gr/m².
Wit papier: 70gr/m² progresso; opdruk zwart. Wanneer P.O.D.: gebruik 80gr/m². 1 A 24-04-'02 10423-10424
- 1 -
DV1201A & DV1221A
Seismic Detectors Installation Manual
Figure 2: Two ways to test the seismic detectors
1/2. 12 VDC 7. Common (C)
3. LED indication 8/9. Tamper
4. Integrator level 10. Test control
5. Normaly Closed (NC) 11. Spare
6. Normaly Open (NO)
!Test disabled (ex-factory setting)
"Internal test of detector’s electronics =
Position jumper between 1 and 2 .
#Function test of the detector and its physical contact
with the protected object = Position connector from
test transmitter DV1215A between 2 and 3.
$
Connecting terminal 10 to 0 V activates both tests.
1. Cover
2. Cover screw
3. Base plate
4. Mounting holes
5. Clamp
6. Area for mounting the
DV1215A test transmitter
7. Potentiometer for adjusting
the detector’s sensitivity
8. Connection block
9. Anti-tamper micro-switch
10. Mounting plate DV1202A
11. Fixing bolt
12. Expander bolt
13. Test transmitter DV1215A
Figure 3: General characteristics of the DV1201A / DV1221A
Using the mounting plate DV1202A as a template
A. Holes for DV1201A / DV1221A
B. Hole for expansion plug or recess mounting box
C. Template and mounting holes for test transmitter DV1215A
D. Holes for accessories.
Figure 4: Mounting the detector directly on a metal surface without using a mounting plate
Figure 1: Wiring diagram
Sentrol
- 2 -
Figure 5: Mounting on concrete
Always use a DV1202A mounting plate. The expansion plug must
penetrate at least 50 mm into the concrete. Please follow the steps
shownin Figure 6 ifyouareinstallingthetest transmitter DV1215A.
$
For the equipment to conform to CEI standard 79-2, the
DV1215A test transmitter must be installed.
Figure 6: Control and function test
Usingavoltmeter,checkthe background signal levelinthedetector
to prevent nuisance alarms. Set the sensitivity to Gmax during the
test.
DV1201A DV1221A Measure
0.7 V 0 V None
1.4 V 2 V Reduce range/remove source
$
Try to remove the source of ambient noise instead of
reducing the range.
Functional testing with hand tester DV1230 !and mechanical
tool ":
DV1201A DV1221A
Alarm in 30 sec. Alarm in 45 sec.
Alarm after 5 blows NA
Detection range (in foot): Technical specifications:
Input power: 9-15 VDC
2 V max. ripple pp
Current consumption: Nom. 8.6 mA
Alarm output: Form C solid state relay, max. series
resistance 35 Ohm
Alarm indication: LED-ind. output 3
Sensitivity: 5 steps of 6 dB each
Range: See Table “Detection range”
Sabotage protection: Temp. 183.2 °F
drill shield,
opening/pry-off contact,
Low voltage alarm: 7.5 V
Temperature limits: -4 °F to + 131 °F
Dimensions: 3.93 x 3.15 x 1.30 inches
Colour: Grey, RAL 7035
Weight: 0.86 lb
Concrete 13.12 45.93 45.93
Steel 1/Gmax 26.25 45.93 45.93
Brick 9.84 26.25 26.25
Concrete 9.84 29.53 29.53
Steel 2/Gref 13.12 29.53 29.53
Brick 3.28 19.69 19.69
Concrete 6.56 19.69 19.69
Steel 3/Gmin 6.56 19.69 19.69
Brick - 13.12 13.12
Concrete 3.28 16.40 16.40
Steel 4 3.28 16.40 16.40
Brick - 9.84 9.84
Concrete - 13.12 13.12
Steel 5 - 13.12 13.12
Brick - 6.56 6.56
Sensitivity
setting
Material Thermal
lance Diamond
disk Drilling
- 3 -
Figure 7: Wiring the DV1201A/DV1221A into Most Security Systems
Figure 8: Connecting the DV1201A to a Four-wire Circuit
Type Control in an UL Complete Mercantile Safe System Figure 9: Connecting the DV1201A to a Two-wire Balanced
Loop Type Control in an UL Complete Mercantile Safe
System
Figure 10: Wire Diagram DV1208A
- 4 -©Sentrol is an Interlogix company. 2002. All rights reserved. 5620-1A
Figure 11
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Interlogix Sensore di sicurezza
Interlogix
Interlogix GS903N Istruzioni per il montaggio
Interlogix
Interlogix RF-EV1012PI-K4 Manuale utente
Interlogix
Interlogix EV1012 Series Istruzioni per il montaggio
Interlogix
Interlogix DC105 Series Istruzioni per il montaggio
Interlogix
Interlogix DC111 Istruzioni per il montaggio
Interlogix
Interlogix VV600 Plus Istruzioni per il montaggio
Interlogix
Interlogix ADC-IS-300-LP-BX Manuale utente
Interlogix
Interlogix VE1120-D Series Istruzioni per il montaggio
Interlogix
Interlogix DD100PI Istruzioni per il montaggio
Interlogix
Interlogix EV660 Series Istruzioni per il montaggio
Interlogix
Interlogix TVK-600 Foglio di istruzioni
Interlogix
Interlogix EV100 Istruzioni per il montaggio
Interlogix
Interlogix VE1016 Series Istruzioni per il montaggio
Interlogix
Interlogix DDI602AM Istruzioni per il montaggio
Interlogix
Interlogix RF-EV1012-K4 Manuale utente
Interlogix
Interlogix TX-4200-01-1 Istruzioni per il montaggio
Interlogix
Interlogix TX-2511-03-1 Istruzioni per il montaggio
Interlogix
Interlogix xGen Lite Guida all'installazione
Interlogix
Interlogix TX-2810-01-4 Istruzioni per il montaggio
Interlogix
Interlogix EV1116-D Series Istruzioni per il montaggio
