Interlogix TX-4200-01-1 Istruzioni per il montaggio

P/N 466-4431 • REV B • 14FEB14 1 / 4

Description

The Personal Panic Device is a wireless

device that can be used to activate police or

auxiliary alarms throughout the premises.

When the help button is pressed, both red

LEDs flash and information is transmitted.

The transmitted signal includes alarm and

battery status information. When the help

button is released, an alarm-restore-all

message is sent. Note: To activate, press

and hold the help button until the red LEDs

stop flashing, then release the button.

The Personal Panic Device is shipped with

a watch type wristband installed. A pendant

adaptor kit and lanyard are also included for

an optional necklace arrangement. The

pendant kit includes a pendant loop and a

pendant plug (shown below).

The Personal Panic Device is water

resistant and has been tested in water at

three meters for one hour.

Installation

Assembly Guidelines

•Program the Personal Panic Device

into the appropriate panel groups.

Refer to the “Programming” section for

more information.

•The transmitter on the Personal Panic

Device has a maximum range of 375

feet. Test the device at the outer limits

of the installation to ensure it works

properly. The outer limits may vary due

to different environments that may

affect the range. Refer to the “Testing”

section for more information.

•Verify the user can activate the help

button by pressing it with their thumb

or finger.

•When worn as a pendant, it is

important that the user does not

activate the help button by pressing it

against their chest. This may reduce

the signal’s effective range.

Watch Style Wristband

Adjust the length of the wristband by

measuring and cutting the band in the

following manner:

1. Position the wristband tightly around

the wrist and in the intended position

as shown in Step 2.

2. Using a washable marker, place a

mark on the edge of each strap, near

the center of the wrist.

Personal Panic Device Installation Sheet

2 / 4 Personal Panic Device Installation Sheet

3. Align the band so the ends of the band

are even. Cut the band in the center of

the two marks as shown below.

4. Attach the band to the clasp. Feed the

band through the retainer opening and

close the lever to lock the band in

place. Repeat for the other side.

Pendant

The Personal Panic Device can be worn as

a pendant by removing the wristband and

installing the pendant adaptor components

and lanyard in the following manner:

1. Remove the two screws on the back of

the Personal Panic Device.

2. Carefully separate the cover and base.

3. Remove the wristband.

4. Separate the components from the

pendant adaptor kit and discard the

circular center section.

5. Insert the pendant loop adapter into

the small loop end of the lanyard.

6. Insert the plugs into the base and

reattach the cover and base. Note:

Compress the panic button and base

assembly together before tightening

the screws.

Programming

Review the following information for adding

a Personal Panic Device to the panel. Refer

to the specific panel Installation Instructions

for further detail.

1. Set the panel to Program Mode.

P/N 466-4431 • REV B • 14FEB14 3 / 4

2. When prompted, enter the appropriate

group number and select the desired

sensor number.

3. Press the help button on the Personal

Panic Device to trip the selected

sensor.

4. Exit from Program Mode.

Maintenance and Testing

Testing

Review the following for testing the help

button. Refer to the specific panel

Installation Instructions for further detail.

1. Set the panel to Sensor Test Mode.

2. Press and hold the help button for a

second to monitor the beeps for the

packet count.

3. Listen for the panel siren. You should

hear 6 to 8 beeps.

4. Test the help button from several

locations to ensure a consistent

response.

5. Test the help button weekly to ensure

proper operation.

6. Verify the end-user can operate the

unit without any difficulty.

Cleaning

1. Gently rub a lanoline-based cleaner,

such as Go-Jo, onto all surfaces of the

Personal Panic Device to remove any

debris.

2. Rinse off using warm water.

3. Wipe clean using a dry, lint-free cloth.

Replacing the Battery

CAUTION: To avoid an alarm

condition set the panel to Sensor Test

Mode prior to changing the battery.

Pour éviter une condition d'alarme

metter le panneau en Mode d'essai

des capteurs avant de changer la

batterie.

CAUTION: Use static electricity

precautions when handling electronic

components.

Utiliser les précautions de l'électricite

statique lors de la manipulation des

composants électroniques.

1. Depending on the situation, it may be

necessary to contact the central

monitoring station before starting the

installation.

2. Remove the two screws on the back of

the Personal Panic Device and

observe how the pendant or wristband

components are attached.

3. Carefully separate the cover and base.

4. Remove the electronic subassembly

from the base.

5. Remove the battery from the electronic

subassembly.

6. Install the new battery. Observe

polarity.

Note: Install Panasonic CR1632.

7. Place the electronic sub assembly into

the base. Note: A generic diagram is

shown above. For diagrams showing

the wristband and pendant

configurations, see the assembly

diagrams in the “Installation/Pendant”

section.

8. Inspect the water seal area and the

plugs to ensure they are free from

debris.

9. Reattach the cover, lanyard assembly

or wristband and the base. Note:

4 / 4 Personal Panic Device Installation Sheet

Press the pushbutton and cover

together before tightening the screws.

10. Test the help button for proper

operation.

11. If the central monitoring station was

notified, inform them this operation is

complete.

Specifications

Model no.

TX-4200-01-1 (white)

TX-4200-01-2 (black)

RF frequency

319.5 MHz

Compatibility

Interlogix Learn Mode Panels

and Receivers

Battery type

3.0 V lithium (CR1632)

Recommended

battery

Panasonic CR1632

Typical standby

current (μA)

≤1

Estimated battery

life

5 years

Supervisory

interval

Less than 64 minutes

Operating

temperature range

32° to 120°F (0° to 49°C)

Storage

temperature range

-30 to 140°F (-34 to 60°C)

Relative humidity

5-90% non-condensing

Dimensions

(L x W x D)

1.60 x 1.40 x 0.410 in. (4.1

x 3.6 x 1.0 cm)

Regulatory Information

Manufacturer

UTC Fire & Security Americas

Corporation, Inc.

1275 Red Fox Rd., Arden Hills,

MN 55112-6943, USA

FCC

Compliance

This device complies with part 15

of the FCC Rules. Operation is

subject to the following two

conditions: (1) This device may

not cause harmful interference,

and (2) this device must accept

any interference received,

including interference that may

cause undesired operation.

Changes or modifications not

expressly approved by Interlogix

can void the user’s authority to

operate the equipment.

FCC ID: B4Z-984-PANIC

IC: 1175C-984PANIC

This Class B digital apparatus

complies with Canadian ICES-

003.

Cet appareil numérique de la

classe B est conforme à la norme

NMB-003 du Canada.

Le fonctionnement est soumis

aux deux conditions suivantes :

(1) cet appareil peut ne pas

provoquer d’interférences et (2)

cet appareil doit accepter toutes

interférences, y compris les

interférences pouvant

provoquer un fonctionnement

non désiré de l’appareil.

US Patents

4,855,713; 4,864,636 and

others pending.

Contact Information

For general information, see

www.interlogix.com. For customer support,

see www.interlogix.com/customer-support

or call +1 855 286 8889.

Interlogix is part of UTC Building and

Industrial Systems, a unit of United

Technologies Corporation. All rights

reserved.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Interlogix Sensore di sicurezza

Interlogix

Interlogix VV600 Plus Istruzioni per il montaggio

Interlogix

Interlogix DD490 Series Istruzioni per il montaggio

Interlogix

Interlogix VE1120-D Series Istruzioni per il montaggio

Interlogix

Interlogix GS960 Istruzioni per il montaggio

Interlogix

Interlogix DDV1016AM Istruzioni per il montaggio

Interlogix

Interlogix AP633A Manuale utente

Interlogix

Interlogix R5812NT Manuale utente

Interlogix

Interlogix ACL870SU-BSMF Manuale utente

Interlogix

Interlogix EV1116-D Series Istruzioni per il montaggio

Interlogix

Interlogix TX-2810-01-4 Istruzioni per il montaggio

Interlogix

Interlogix EV520-P Series Istruzioni per il montaggio

Interlogix

Interlogix RF-EV1012PI-K4 Manuale utente

Interlogix

Interlogix ACL800SUW-BSPX Manuale utente

Interlogix

Interlogix Sentrol DV1201A Manuale utente

Interlogix

Interlogix PB501 Istruzioni per il montaggio

Interlogix

Interlogix EV1012 Series Istruzioni per il montaggio

Interlogix

Interlogix DD1012AM-D Istruzioni per il montaggio

Interlogix

Interlogix DD669 Istruzioni per il montaggio

Interlogix

Interlogix DD100PI Istruzioni per il montaggio

Interlogix

Interlogix DC418 Scheda tecnica

Interlogix

Interlogix DC105 Series Istruzioni per il montaggio

Interlogix

Interlogix SB Series Manuale utente

Interlogix

Interlogix DDI602AM Istruzioni per il montaggio

Interlogix

Interlogix EV1116 Series Istruzioni per il montaggio

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente