Interlogix NS3500-28T-4S Manuale utente

NS3500-28T-4S

Quick Start Guide

P/N 1072836 • REV 00.01 • ISS 14JUL14

- 2 -

Interlogix is part of UTC Building & Industrial Systems, Inc. a unit of United Technologies

Trademarks and

patents The NS3702-24P-4S name and logo are trademarks of United Technologies.

Other trade names used in this document may be trademarks or registered trademarks

of the manufacturers or vendors of the respective products.

Manufacture

Interlogix

3211 Progress Drive, Lincolnton, NC 28092 USA

Authorized EU manufacturing representative:

UTC Climate Controls & Security B.V.,

Kelvinstraat 7, 6003 DH Weert, Netherlands

Intended use Use this product only for the purpose it was designed for; refer to the data sheet and

user documentation for details. For the latest product information, contact your local

supplier or visit us online at www.interlogix.com.

Certification N4131

FCC compliance This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications.

You are cautioned that any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate the

equipment.

ACMA compliance Notice! This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate measures.

Canada This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme á la norme NMB-003du Canada.

European Union

directives 2004/108/EC (EMC Directive): Hereby, UTC Building & Industrial Systems, Inc.

declares that this device is in compliance with the essential requirements and other

relevant provisions of Directive 2004/108/EC.

Contact Information For contact information, see www.interlogix.com or www.utcfssecurityproducts.eu.

- 3 -

Table of Contents

1. PACKAGE CONTENTS......................................................................................................................................................4

2. REQUIREMENTS...............................................................................................................................................................5

3. TERMINAL SETUP.............................................................................................................................................................6

4. LOGON TO THE CONSOLE..............................................................................................................................................7

5. CONFIGURING IP ADDRESS VIA THE CONSOLE..........................................................................................................8

6. SAVING THE CONFIGURATION VIA THE CONSOLE.....................................................................................................9

7. STARTING WEB MANAGEMENT ...................................................................................................................................10

8. SAVING CONFIGURATION VIA THE WEB.....................................................................................................................14

9. RECOVERING BACK TO DEFAULT CONFIGURATION................................................................................................15

10. CUSTOMER SUPPORT .................................................................................................................................................16

- 4 -

1. Package Contents

Thank you for purchasing NS3500-28T-4S - 28-Port 10/100/1000Mbps + 4-Port Shared SFP

Managed Gigabit Switch.

The “Managed Switch” mentioned in this Guide refers to the NS3500-28T-4S.

Open the box of the Managed Switch and carefully unpack it. The box should contain the following

items:

 The Managed Switch x 1

 Quick Installation Guide x 1

 RS-232 to RJ-45 Cable x 1

 Rubber Feet x 4

 Two Rack-mounting Brackets with Attachment Screws x 1

 Power Cord x 1

 SFP Dust-proof Cap x 4

If any item is found missing or damaged, please contact your local reseller for replacement.

- 5 -

2. Requirements

 Workstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later, Linux, UNIX, or other

platforms are compatible with TCP/IP protocols.

 Workstations are installed with Ethernet NIC (Network Interface Card)

 Serial Port Connection (Terminal)

 The above Workstations come with COM Port (DB9) or USB-to-RS-232 converter.

 The above Workstations have been installed with terminal emulator, such as Hyper Terminal

included in Windows XP/2003.

 Serial cable -- one end is attached to the RS-232 serial port, while the other end to the console port

of the Managed Switch.

 Ethernet Port Connection

 Network cables -- Use standard network (UTP) cables with RJ-45 connectors.

 The above PC is installed with Web Browser and JAVA runtime environment plug-in.

Note: It is recommended to use Internet Explorer 8.0 or above to access the Managed Switch.

If the Web interface of the Managed Switch is not accessible, please turn

off the anti-virus software or firewall and then try it again.

- 6 -

3. Terminal Setup

To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to

RJ-45 type of console port of the Managed Switch.

Figure 3-1 Managed Switch Console Connectivity

A terminal program is required to make the software connection to the Managed Switch.

1. Run terminal program on the OS.

2. When the following screen appears, make sure that the COM port should be configured as:

Baud : 115200

Data bits : 8

Parity : None

Stop bits : 1

Flow control : None

Figure 3-2 COM Port Configuration

- 7 -

4. Logon to the Console

Once the terminal is connected to the device, power on the Managed Switch and the terminal will

display “running testing procedures”. Then, the following message asks to log-in user name and

password. The factory default user name and password are shown as follows and the login screen in

Figure 4-1 appears.

Username: admin

Password: admin

Figure 4-1: Managed Switch Console Login Screen

The user can now enter commands to manage the Switch.

For a detailed description of the commands, please refer to the following chapters.

Note:

1. For security reason, please change and memorize the

new password after this first setup.

2. Only accept command in lowercase letter under console

interface.

- 8 -

5. Configuring IP Address via the Console

The Managed Switch is shipped with default IP address as follows:

IP Address: 192.168.0.100

Subnet Mask: 255.255.255.0

To check the current IP address or modify a new IP address for the Switch, please use the

procedures as follows:

 Display of the current IP address

1. On” NS3500-28T-4S #” prompt, enter “show ip”.

2. The screen displays the current IP address, Subnet Mask and Gateway shown in Figure 5-1.

Figure 5-1: IP Information Screen

Configuration of the IP address

3. On” NS3500-28T-4S#” prompt, enter “configure”.

4. On“ NS3500-28T-4S(config) #” prompt, enter the following command and press <Enter> as

shown in Figure 5-2.

NS3500-28T-4S(config) # ip address 192.168.1.100 mask 255.255.255.0

NS3500-28T-4S(config) # ip default-gateway 192.168.1.254

The previous command would apply the following settings for the Switch.

IP Address: 192.168.1.100

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.254

Figure 5-2: Setting IP Address Screen

5. Repeat Step 1 to check if the IP address is changed.

If the IP is successfully configured, the Managed Switch will apply the new IP address setting

immediately. You can access the Web interface of Managed Switch through the new IP address.

Note: If you are not familiar with console command or the related

parameter, enter “?” anytime in console to get the help description.

6. Saving the Configuration via the Console

In switch, the running configuration file stores in the RAM. In the current version, the running

configuration sequence running-config can be saved from the RAM to FLASH by write command or

copy running-config startup-config command, so that the running configuration sequence

becomes the start up configuration file, which is called configuration save.

1. On “NS3500-28T-4S#” prompt, enter “copy running-config startup-config” as shown in Figure

6-1.

Figure 6-1: Saving the Configuration Screen

- 10 -

7. Starting Web Management

The following shows how to st art up the Web Management of the Managed Switch. Note th e

Managed Switch is c onfigured through an Ethernet connection. Please make sure the manager PC

must be set on the same IP subnet address.

For example, the default IP address of the Managed Switch is 192.168.0.100; then the manager PC

should be set at 192.168.0.x (where x is a number between 1 and 254, except 100) and the default

subnet mask is 255.255.255.0.

Figure 7-1: IP Management Diagram

Altri manuali per NS3500-28T-4S

Indice

Altri manuali Interlogix Interruttore

Interlogix

Interlogix NS2052-8P-2C Manuale utente

Interlogix

Interlogix NS3550-8T-2S Manuale utente

Interlogix

Interlogix GE-DS Series Manuale utente

Interlogix

Interlogix NS3553-4P-1T-2S Manuale utente

Interlogix

Interlogix IFS NS3550-24T/4S Manuale utente

Interlogix

Interlogix NS4702-24P-4X Istruzioni per l'installazione

Interlogix

Interlogix NS4702-24P-4S-4X Manuale utente

Interlogix

Interlogix NS3702-24P-4S Manuale utente

Interlogix

Interlogix NS4750-24S-4T-4X Manuale utente

Interlogix

Interlogix NS3562-8P-2S Manuale utente

Interlogix

Interlogix NS4750-24S-4T-4X Manuale utente

Interlogix

Interlogix MC251-4P/1S Manuale utente

Interlogix

Interlogix NS3552-8P-2S Manuale utente

Interlogix

Interlogix NS3503-16P-4C Manuale utente

Interlogix

Interlogix NS4702-24P-4S-4X Manuale utente

Interlogix

Interlogix IFS ANT-PNL-18DB-2G Manuale utente

Interlogix

Interlogix IFS NS2503-8P/2C Manuale utente

Interlogix

Interlogix IFS NS2052-4P-1T Manuale utente

Interlogix

Interlogix NS3702-24P-4S-V2 Manuale utente

Interlogix

Interlogix POC2502 Series Manuale utente

Interlogix

Interlogix IFS MC350-4T-2S Manuale utente

Interlogix

Interlogix NS3503-16P-4C Manuale utente

Interlogix

Interlogix NS3500-28T-4S Manuale utente

Interlogix

Interlogix NS3552-8P-2S Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente