2
SPECIFICATIONS AND OTHER INFORMATION
1. Radio Transmitters and Receivers are sensitive to heat.
Avoid mounting them above heaters or air conditioners and
avoid installing in direct afternoon sunlight.
2. This Transmitter is not waterproof.
3. The higher the Receiver Module, the longer its range. For good
range and reliable reception, make sure Modules are mounted
as high as practical above ground level with antenna at top.
4. Environmental conditions could affect the operation of the Remote
Control System. For example, in rain the range may be less than normal.
5. To prevent electronic interference, install Receiver Modules as least
3 feet apart.
OPERATION
Because of our commitment to continuing research and improvements, Intermatic Incorporated reserves the right to make changes, without notice, in the specifications and material
contained herein and shall not be responsible for any damages, direct or consequential, caused by reliance on the material presented.
INTERMATIC INCORPORATED, SPRING GROVE, IL 60081
158RC12945
A. To Set Code
Receiver Modules have the capacity to “learn”
and remember a unique code generated by a
Transmitter. The Transmitter will operate only the
designated one or more Receivers simultaneously.
In addition, each Transmitter can “teach” and
operate up to three different Receivers.
Also, more than one Transmitter can be assigned
to operate the same Receivers.
1. Turn ON the main power to the Receiver and
manually operate the load a few times, then turn
load OFF.
2. Holding the transmitter close to the Receiver
Module, press and hold the push-button you choose
to operate that particular Module. The red LED
INDICATOR SHOULD NOW BE LIT.
3. Press the ‘CODE SET” button on the face of the
Receiver Module until the green light next to the
button flashes ONCE (about one second).
4. Code setting is now complete. Release the
Transmitter button and test installation by pressing
repeatedly on the chosen transmitter button.
The load should cycle ON/OFF, if not, repeat
steps 2 and 3 above.
5. To add another receiver module and have them
operate TOGETHER, repeat the above procedure
on the next receiver module holding down the
SAME transmitter button in step 2. Hold down
a DIFFERENT transmitter button to have them
operate independently.
To erase all memorized codes, press and hold CODE
SET button on Receiver Module, until the green indica-
tor
light alongside goes out (in about 6 seconds).
To operate a Receiver Module with more than one
transmitter, set master code switch, next to the battery
in Transmitters to the same setting.
To Change Battery: Remove connecting screw in
transmitter case. Set aside top of case and discard old
battery. Snap connector onto new battery. Replace the
top of case and the connecting screw.
LIMITED ONE YEAR WARRANTY
If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace
it, at its sole option, the unit free of charge. This warranty applies only to the original purchaser and is not transferable. This warranty does not apply
to: (a) damage caused by accident, abuse, mishandling, dropping, acts of God, or any negligent use; (b) units which have been subject to unauthor-
ized repair, opened, taken apart, or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the
product. Some states do not allow a limitation of damages, so the foregoing limitation may not apply to you. This warranty gives you specific legal
rights and you may have other rights that vary from state to state.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER
EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE
OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product,
along with proof of purchase, postage prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/
After Sales Service, 7777 Winn Rd., Spring Grove, IL 60081-9698/815-675-7000 http://www/intermatic.com Please be sure to wrap the product
securely when mailing to avoid shipping damage.
