Intermec EasyCoder 201II Manuale utente

EasyCoder 201 II

Label-Taken Sensor Kit

P/N 1-960255-04

Edition 3

September 1998

Installation Instructions

EasyCoder 201 II – Installation Instructions

This booklet contains instructions on how to install the Label-

Taken Sensor Kit (LTS) on an EasyCoder 201 II printer. Installa-

tion should preferably be performed by an authorized service

technician.

For instructions on how to use the label-taken sensor, please refer

to the EasyCoder 201 II Technical Manual.

The Label-Taken Sensor kit consists of:

• 1 Reflecting Sensor assy. with bracket and cable

• 1 Screw

• This Installation Instructions booklet.

The status of the LTS has to be polled in the Intermec Fingerprint

programbymeansofthePRSTAT function,asotherwisetheprinter

will not react on the LTS signal.

❑Make a simple program that checks the printer's status, e.g.:

10 BREAK 1,88

20 BREAK 1 ON

30 FORMFEED

40 IF (PRSTAT AND 2) THEN BEEP

50 GOT0 40

60 END

RUN

You can break this program by transmitting the character X

(ASCII 88) decimal on the standard serial interface "uart1:".

LABEL-TAKEN SENSOR KIT

General Information

Preparation Before

Installation

Informationinthismanualissubjecttochangewithoutpriornoticeanddoesnot

represent a commitment on the part of Intermec Printer AB.

©CopyrightIntermecPTCAB,1998.Allrightsreserved.PublishedinSweden.

EasyCoder and Fingerprint are registered trademarks of Intermec Technolo-

gies Corp.

EasyCoder 201 II

Label-Taken Sensor Kit

Installation Instructions

Edition 3, September 1998

Part No. 1-960255-04

EasyCoder 201 II – Installation Instructions

LABEL-TAKEN SENSOR KIT, cont'd.

❑Turn off the power and remove the power cord.

❑Disconnect all communication cables.

❑Open the right-hand door.

❑Loosen the two screws that lock the cover.

❑Pull the cover straight back and remove it completely.

❑Open the left-hand door.

❑LoosenthethreescrewsthatholdtheCPUboardassy.andswing

the unit outwards as illustrated.

Step-by-Step Installation

Instructions

CoverScrews (2x)

230V

CPU Board Assy.

Screw (1x)

Screws (2x)

Continued!

EasyCoder 201 II – Installation Instructions

❑Remove the two screws that hold the front moulding.

❑Carefully manipulate the moulding so you can slip the cable of

the label-taken sensor through the gap between the moulding

and the centre-line wall of the printer.

❑Thread the cable back to the electronics compartment and

connectittoP-8ontheCPUboard,see nextpage.Becareful so

the cable will not interfere with the pulley of the print roller or

with the printhead lift mechanism.

❑Using the screw included in the kit, fit the sensor and the front

moulding as illustrated. The tab at the top of the sensor bracket

should be fitted into the lower of the two cross-shaped holes in

the front moulding.

❑Putback theoriginal (upper)screw holdingthe frontmoulding.

LABEL-TAKEN SENSOR KIT, cont'd.

Step-by-Step Installation

Instructions, cont'd.

LTS assy.

Tab

Front Moulding

Original Screw

Cable

New Screw

(incl. in the kit)

Continued!

EasyCoder 201 II – Installation Instructions

P-8

LTS

Step-by-Step Installation

Instructions, cont'd.

LABEL-TAKEN SENSOR KIT, cont'd.

❑Fitthe cablefromthe label-takensensor toconnector P-8at the

lower, front part of the CPU board.

❑Close the doors and cover in reverse order, refit the com-

munication cables and the power cord, and turn on the power.

❑Adjust the sensitivity of the label-taken sensor by means of the

uppermost potentiometer on the printer's rear plate:

• StartupFingerprintandruntheprogramdescribedonpage1.

Leave a label in the outfeed slot as to create a label-not-taken

condition.

• The printer should start to beep continuously. If not, turn the

potentiometer back and forth until the beeping starts.

• Adjust the potentiometer so the beeping does not stop when

the potentiometer is turned a quarter of a turn in either

direction.

• Remove the label. The beeping should cease immediately. If

necessary, readjust the potentiometer1.

• Break the program by typing Xon the host.

WARNING!

To avoid the risk of short-circuits, use

non-conductivetoolsonly,evenwhen

the power is off, since the memory

packages are battery backed-up.

The potentiometer is situated inside the

cover plate on the printer's rear plate.

CPU Board

P-8

Connect cable here!

1/.Ifadjustmentbymeansofthepotentio-

meter is proves insufficient, a strap on

P-14 on the CPU board can be fitted or

removed to change the sensitivity of the

LTS light-emitting diode:

Strap fitted: Higher intensity

No strap: Low intensity

MADE IN SWEDEN

Thermal Printer 201

Model #

1-201011-11

Serial #

115-230V 2.6-1.3A 50-60Hz

INTERMEC PRINTER AB MADE IN SWEDEN

50105

This equipment complies with the requirements for a Class Acomputing device in FCC Rules

Part 15 Subpart J. Operation of this device in a residential area may cause harmful interference

requiring the user to take whatever steps may be necessary to correct the interference.

LISTED 65B5

N309

LR67809

geprüfte

Sicherheit

Label-taken sensor

adjustment

Altri manuali per EasyCoder 201II

Indice

Altri manuali Intermec Etichettatrice

Intermec

Intermec EasyCoder E4 Manuale utente

Intermec

Intermec EasyCoder PX4i Manuale utente

Intermec

Intermec EasyCoder PX4i Manuale utente

Intermec

Intermec EasyCoder 4420 Manuale utente

Intermec

Intermec EasyCoder PX6i Manuale utente

Intermec

Intermec PB51 Manuale utente

Intermec

Intermec EasyCoder 501XP Manuale utente

Intermec

Intermec PM43c Manuale utente

Intermec

Intermec ColorCoder V4 Manuale utente

Intermec

Intermec PM43 Manuale utente

Intermec

Intermec EasyCoder 4420 Manuale utente

Intermec

Intermec PM4I Manuale utente

Intermec

Intermec PB22 Manuale utente

Intermec

Intermec EasyCoder PD4 Manuale utente

Intermec

Intermec EasyCoder PX6i Manuale utente

Intermec

Intermec EasyCoder PF4i Manuale utente

Intermec

Intermec EasyCoder 401 Manuale utente

Intermec

Intermec EasyCoder 3400e Manuale utente

Intermec

Intermec EasyCoder 501XP Manuale utente

Intermec

Intermec EasyCoder E4 Manuale utente

Intermec

Intermec EasyCoder PX4i Manuale utente

Intermec

Intermec EasyCoder F2 Manuale utente

Intermec

Intermec EasyCoder PC4 Manuale utente

Intermec

Intermec PM4I Manuale utente

Manuali Etichettatrice popolari di altre marche

Brother

Brother P-Touch 2420PC Manuale utente

newell

newell Dymo LabelManager 210D Manuale utente

Brother

Brother TD-4000 Manuale utente

U-Line

U-Line BROTHER H-8754 Manuale utente

Tharo Systems

Tharo Systems H-435+ Manuale utente

Brother

Brother E300 Manuale utente

Godex

Godex RT700 SERIES Manuale utente

ID Technology

ID Technology 252 Manuale utente

Labelmate

Labelmate MC-11 Manuale utente

CAB

CAB XD4M/300 Manuale utente

Avery Dennison

Avery Dennison Pathfinder 6057 Manuale di servizio

Brother

Brother P-touch PT-9700PC Manuale utente

TSC

TSC PEX1000 Series Manuale utente

Adkins

Adkins Label Master Manuale utente

Epson

Epson LabelWorks LW-400 Manuale utente

Primera

Primera 510212 Manuale utente

Brady

Brady BradyPrinter S3100 Manuale utente

DuraLabel

DuraLabel LabPRO Manuale utente