ISLABIKES Icons Joni Manuale utente
www.islabikes.co.uk
Icons Joni
Owner’s manual
Icons - Joni
1. Brake levers
2. Brake calipers
3. Rotors
4. Saddle
5. Seatpost
6. Seatpost clamp
7. Saddle clamp
8. Stem
9. Stem bolts
10. Headset
11. Headset spacers
12. Headset adjuster bolt
13. Handlebars
14. Grip shift
15. Rim
16. Spokes
17. Tyres
18. Chain
19. Rear derailleur
20. Cassette
21. Frame
22. Forks
23. Cranks
24. Pedals
25. Mudguards
26. Luggage rack
Setting up your Icons Joni
5
1
11
9
12
6
15
17
19
18
21
22
23
14
4
10
13
16
2
3
7
8
20
25
24
26
www.islabikes.co.uk
Step 1 of 6
Remove front wheel and fork packaging
1. Remove front wheel
protection packaging.
2. Remove fork protector
DO NOT PULL BRAKE
when caliper spacer
is removed. Please
keep caliper spacer for
transportation when wheel
is removed
3. Remove brake caliper spacer
Icons - Joni
Step 2 of 6
Install quick release and secure front
wheel in fork
1. Install front quick release (QR)
skewer from pedal box
Ensure QR skewer springs
orientation is correct
2. Put front wheel into the fork.
Ensure (QR) lever is not on
gear side.
Check this matches the
rear wheel
www.islabikes.co.uk
Step 2 of 6
Install quick release and secure front
wheel in fork continued
3. Hold QR lever in fully ‘open’
position and turn nut
clockwise. Do not fully
tighten nut.
4. Clamp the QR to fully closed
position in line with the fork.
Tighten
The QR lever should start to feel tight at 90 degrees as you close –
if it is too tight or too loose you can adjust by holding lever ‘open’
again and turning nut.
Check front wheel is correctly installed. Firstly, lift the front end of
the bike o the ground by the handlebars and strike the top of the
wheel rmly with the palm of your hand. Secondly, push and pull
the wheel from side to side. If there is no movement from either of
these actions the wheel is installed correctly.
Clamp
Icons - Joni
Step 3 of 6
Handlebar set up
1. Turn handlebars clockwise and align with front wheel
2. Tighten the two stem clamp bolts Max. 7Nm
Caution: The fork steerer tube is carbon bre construction, which
can be seriously damaged by over tightening.
Failure to correctly tighten stem clamp bolt may result in serious
injury or death. If in doubt, please consult our technical support
Before riding check front brake operation is correct. To check this,
apply both the front and rear brake, they should feel the same.
Secondly, push the bike forward whilst holding the front brake to
ensure it is working.
Turn
Do Not Over
Tighten
Tighten
www.islabikes.co.uk
Step 4 of 6
Pedal installation
1. Left pedal: Rotate pedal axle clockwise towards front of bike
2. Right pedal: Rotate pedal axle anti-clockwise towards front of bike
Tighten max. 30Nm
Please ensure you identify the left and right pedals before installing.
Tighten
Tighten
a. Left pedal
b. Right pedal
Icons - Joni
Step 5 of 6
Adjust saddle height
1. Loosen seatpost-clamp
2. Move to desired height
3. Tighten clockwise max. 4Nm
Seatposts are clearly marked with minimum insertion mark.
Please do not raise saddle above this line.
Tighten
www.islabikes.co.uk
Step 6 of 6
Brake pad bed-in
It is important to bed-in your new brake pads to achieve optimal
performance, increase pad longevity and reduce the likelihood of brake
fade and noise.
To safely achieve optimal results, remain seated on the bike during the
entire bed-in procedure. Accelerate the bike to a moderate speed (12mph /
20kph), then rmly apply the brakes until you are at walking speed. Repeat
approximately twenty times. Next, accelerate the bike to a faster speed,
then rmly apply the brakes until you are at a walking speed. Repeat
approximately ten times.
Important: do not lock up the wheels at any point during the bed-in
procedure. Allow the brakes to cool prior to any additional riding. If you
require further information about your brakes, contact our technical support
team on +44 (0)800 008 6297 or email techsupport@islabikes.co.uk.
Icons - Joni
Ready to ride
Safety rst
Before you head off please read our advice for safe cycling.
Ensure that your helmet is adjusted correctly in accordance with
the manufacturer’s instructions.
Ensure you are wearing sturdy footwear and nothing can become
entangled in the pedal or drivetrain.
Ensure that you familiarise yourself with your new bicycle in a safe
environment. We pride ourselves on light action brakes. Check you
can come to a stop safely using the brakes.
Your Islabike is set up so that the right-hand brake lever operates
the front brake. Where the destination country drive on the right the
right hand brake lever will operate the rear brake.
Be aware braking performance and grip will be drastically reduced
in wet conditions.
Ride carefully on busy streets or highways.
Always observe national legal requirements if riding on public
roads. If you are cycling in any other countries or in the EU, please
check national guidelines.
It is important that your bike is regularly maintained. It should be
inspected if an accident occurs.
Indice
Altri manuali ISLABIKES Bicicletta
ISLABIKES
ISLABIKES Beinn 20 Pro Series Manuale utente
ISLABIKES
ISLABIKES luath pro series Manuale utente
ISLABIKES
ISLABIKES Rothan Manuale utente
ISLABIKES
ISLABIKES Joni 20 Manuale utente
ISLABIKES
ISLABIKES Creig Manuale utente
ISLABIKES
ISLABIKES Icons Janis Manuale utente
ISLABIKES
ISLABIKES Creig Series Manuale utente
ISLABIKES
ISLABIKES eJoni Manuale utente
ISLABIKES
ISLABIKES Rothan Manuale utente
ISLABIKES
ISLABIKES Icons Jimi Manuale utente
