J-TECH JTECH-4K88-EX-RX Manuale utente
Operating Instructions
Website: www.jtechdigital.com
Toll Free: 1-888-610-2818[US]
Email: Support@jtechdigital.com
J-Tech Digital® 4K HDMI Distribution Hub
JTD-ID: 435
The JTECH-4K88-EX 4K HDMI Distribution Hub Control Path has been tested for
conformity to safety regulations and requirements, and has been certified for
international use. However, like all electronic equipment, the JTECH-4K88-EX
should be used with care. Please read and follow the safety instructions to protect
yourself from possible injury and to minimize the risk of damage to the unit.
Follow all instructions and warnings marked on this unit.
Do not attempt to service this unit yourself, except where explained in this
manual.
Provide proper ventilation, air circulation, and do not use near water.
Keep objects that might damage the device away and assure that the placement
of this unit is on a stable surface.
Use only the power adapter, power cords, and connection cables designed for
this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power
to the device before cleaning.
SAFETY AND NOTICE
INTRODUCTION....................................................................................................................1
PACKAGE LIST .......................................................................................................................1
FEATURES .............................................................................................................................2
PANEL DESCRIPTION.............................................................................................................3
SYSTEM CONNECTION ..........................................................................................................6
IR REMOTE CONTROL ...........................................................................................................7
IR PASS-THROUGH CONTROL................................................................................................8
SIGNAL SWITCHING............................................................................................................11
RS232 CONTROL.................................................................................................................12
RS232 CONTROL COMMANDS ............................................................................................14
TCP/IP CONTROL ................................................................................................................23
GUI FOR TCP/IP CONTROL ..................................................................................................25
GUI UPDATE .......................................................................................................................29
EDID MANAGEMENT ..........................................................................................................30
FIRMWARE UPDATE............................................................................................................31
SPECIFICATION ...................................................................................................................32
PANEL DRAWING ................................................................................................................34
TROUBLESHOOTING & MAINTENANCE...............................................................................35
TABLE OF CONTENTS
The kit is a professional 4K HDBaseT HDMI Distribution Hub Kit, which consists of a
4K HDBaseT Matrix Switcher, 7 HDBaseT Receivers and accessories.
The JTECH-4K88-EX is a professional 8x8 HDBaseT Matrix Switcher that consist of
the following inputs and outputs, 8 HDMI IN (4kx2K@60Hz signal at max), 7 IR IN, 1
IR EYE, 8 IR OUT, 1 IR OUT ALL, 7 HDBaseT OUT, 1 HDMI OUT, 1 SPDIF OUT, 1
L&R RCA OUT, and TCP/IP, RS232 control port via phoenix connector.
The JTECH-4K88-EX-RX is an HDBaseT Receiver that consists of the following
inputs and outputs, 1 HDBaseT IN, 1 IR IN, 1 IR OUT and HDMI OUT. The receiver
is powered directly by the Matrix Switcher.
All HDMI inputs can be selected by either the front panel buttons, IR, RS232 or GUI.
The selected source is delivered to HDBaseT zoned outputs 1~7 & HDMI Output.
The Matrix Switcher is capable of delivering 4K signals up to 40m, 1080p up to 70m
and powering the receivers via a single CAT5e cable. It is however recommended to
use good quality CAT6 cable.
The Matrix Switcher supports EDID management and is HDCP 2.2, 1.4 compliant.
Audio sources can be selected via RS232 commands and TCP/IP at the Matrix
Switcher or by 3rd Party control.
4K HDBaseT
Matrix Switcher
1 x JTECH-4K88-EX 4K HDBaseT Matrix Switcher
2 x Mounting ears & 6 x Screws
4 x Trapezoidal Plastic pads
1 x Power Cord
8 x IR Receivers
9 x IR Emitters
1 x IR Remote
1 x RS232 cable(Phoenix to DB9)
HDBaseT
Receivers
7 x JTECH-4K88-EX-RX HDBaseT Receivers
14 x Mounting ears & 28 x Screws
28 x Round Plastic pads
1 x User manual
INTRODUCTION
PACKAGE LIST
1
HDBaseT Matrix Switcher that features 7 HDBaseT outputs and 1 HDMI output.
Supports HDCP 2.2, and is backwards compatible with previous version of HDCP
and HDMI.
Transmits 4Kx2K @ 60Hz 4:2:0 up to 26 ft. (8m) via HDMI port and 131 ft. (40m)
via HDBaseT port.
7 HDBaseT outputs with distances up to 230 ft. (70m) at 1080p and 131 ft. (40m)
at 4Kx2K on a single Cat5e/6 cable.
HDBaseT Receivers are powered by the matrix using PoC technology.
LED indicators show real-time switching status
Controllable via front panel, RS232, IR and TCP/IP.
Built-in GUI for TCP/IP control and setup.
Powerful EDID management.
Support CEC to control far-end display devices via RS232 commands.
Features Micro USB port for firmware upgrades.
Easy installation with rack-mounting design, mounting hardware included.
Power Supply: Matrix Unit, AC100V~ 240V; Receivers, PoC.
FEATURES
2
HDBaseT Matrix Switcher
Front Panel
No.
Name
Description
①
FIRMWARE
Micro USB port for updating firmware.
②
Power Indicator
Red when DC power present or Standby Mode.
③
INPUTS
8 input selector buttons & 8 green indicators. Numbered
from “1” to “8”.
④
OUTPUTS
8 output selector buttons & 8 green indicators, press
the buttons to switch input cycle for the outputs.
Rear Panel
No.
Name
Description
①
INPUTS
8 x HDMI inputs: Type A female HDMI connector,
connect the source device with an HDMI cable to any
of the HDMI inputs.
②
OUTPUTS
7 x HDBaseT outputs: The HDBT RJ45 outputs
deliver HD video, Audio and PoC to the HDBaseT
Receiver up to 70m.
1 x HDMI output: Connect an HDMI cable from the
Matrix Switcher to the displayer.
FIRMWARE
INPUTS
OUTPUTS
1 2 3 4 5 6 7 8
4K HDMI2.0 8X8 Matrix Extender / JTD-ID:435
124
3
1 1 2 3 4 5 6 7 8 ALL2 3 4 5 6 7 IR EYE
1 2 3 4 56 7 8 1-HDBT 3-HDBT 4-HDBT 5-HDBT 6-HDBT 7-HDBT 8-HDMI
Tx Rx
RS232 8-SPDIF L R8
TCP/IP
INPUTS OUTPUTS
IR IN IR OUT CONTROL AUDIO OUTPUT
12
34567
PANEL DESCRIPTION
3
No.
Name
Description
③
IR IN
7 x IR IN: Connect with IR receiver, fixed IR input for
the output, cannot be switched separately. It makes
up an IR bi-directional transmission with the IR OUT
on the corresponding HDBaseT receiver.
1 x IR EYE: Connect with extended IR receiver, use
the IR remote to control the Matrix Switcher.
④
IR OUT
8 x IR OUT: Plug in IR emitters to deliver the IR signal
sent from the far-end receivers connected to the
HDBaseT ports. These IR OUT sockets make up an
IR matrix with the IR IN sockets on the far-end
receivers, and all can be switched simultaneously with
the AV signal, or separately from switching. In default
setting, the 1~7 IR OUT corresponds with the 1~7 IR
IN, i.e. IR OUT1 - IR IN1, IR OUT2 - IR IN2, …IR
OUT7 - IR IN7.
1 x IR ALL OUT: Plug in IR emitter to deliver the IR
signal to control input source device form any of
far-end receivers.
⑤
CONTROL
RS232: Serial port for unit control, 3-pin pluggable
terminal block, connects with control device (e.g. PC).
TCP/IP: RJ45 port. Connect with PC for Web-based
GUI control.
⑥
AUDIO
OUTPUTS
SPDIF: Digital audio output connects directly via an
optic fiber cable to the Toslink input on a sound bar.
RCA (L&R): PCM Analogue audio output sockets
connect the de-embedded audio additional speakers.
⑦
AC100V~240V
Power port, connect with power cord.
PANEL DESCRIPTION
4
HDBaseT Receiver
Front & Rear Panel
No.
Name
Description
①
HDMI OUT
Connect to HDMI display.
②
IR IN
Plug in the IR receiver, this will receive the IR signals
from the RCU and send through to the Matrix Switcher
and then control the desired source.
③
IR OUT
Plug in the IR emitter and attached to the fornt of the
display, this will send the IR signals form the Matrix
Switcher to control the display which is connected to
the HDMI OUT port.
④
Power Indicator
RED when DC power present (PoC).
⑤
TP IN
The RJ45 socket has two LED status indicators. Plug in
the Pre-installed CAT cable in to the HDBT RJ45
socket.
HDCP: HDCP compliant indicator
OFF: No HDMI traffic (no picture); GREEN: Signals with
HDCP; Blinking GREEN: Signal without HDCP.
LINK: HDBT Link status indicator
OFF: No Link; YELLOW: Link Successful; Blinking
YELLOW: Link Error.
IR IN IR OUTHDMI OUT TP IN
LINK HDCP
12345
PANEL DESCRIPTION
5
Usage Precautions
Verify all components and accessories included before installation.
System should be installed in a clean environment with proper temperature and
humidity.
All of the power switches, plugs, sockets and power cords should be insulated
and safe.
All devices should be connected before power on.
System Diagram
Note:
Connect HDBT ports of Matrix Switcher and far-end HDBaseT Receivers with
straight-through cable.
IR receivers connected to IR IN should be with carrier. If not, send
command %0900. or %0901.to activate native carrier mode or force carrier mode
in the IR matrix launched between Matrix Switcher and far-end HDBaseT
Receiver.
1 1 2 3 4 5 6 7 8 ALL2 3 4 5 6 7 IR EYE
1 2 345 6 7 8 1-HDBT 3-HDBT 4-HDBT 5-HDBT 6-HDBT 7-HDBT 8-HDMI
Tx Rx
RS232 8-SPDIF L R8TCP/IP
INPUTS OUTPUTS
IR IN IR OUT CONTROL AUDIO OUTPUT
Central Control System Router iPad Speaker
Amplifier
Apple RemoteIR Receiver
HDTV
Receiver
HDTV
Remote
IR Receiver
TV RemoteIR Receiver
HDMI:
Audio:
Internet:
Control:
HDBaseT:
SYSTEM CONNECTION
6
IR REMOTE
Connect an IR receiver to the IR EYE port of the Matrix Switcher, users can control it
through the included IR remote. Here is a brief introduction to the IR remote.
①Standby button:
Press it to enter/ exit standby mode.
②INPUTS:
Input channel selection buttons, range from 1~8.
③OUTPUTS:
Output channel selection buttons, range from 1~8.
④Menu buttons:
ALL: Select all outputs.
EDID management button: Enable input port to
manually capture and learn the EDID data of output
devices.
CLEAR: Withdraw an operation like switching output
channel, learning EDID data before it comes into
effect. Meanwhile, the matrix will return to the
previous status.
ENTER: Confirm operation.
INPUTS
OUTPUTS
MENU
1 2 3
456
7 8
1 2 3
456
7 8
ALL EDID
CLEAR ENTER
1
2
3
4
IR REMOTE CONTROL
7
Questo manuale è adatto per i seguenti modelli
1
Indice
