Janus C4 I/O Blade Manuale utente
Page 1
Version 1.0 February 2019
Specication
The Janus C4 I/O Blade is a plug-in unit that can be
purchased with either the Janus C4 Single-Blade
Controller (Part No: JC4-ADV-C2-SNG) or the Janus C4
Multi-Blade Controller (Part No: JC4-ADV-C2-MLT).
Each I/O Blade enables the connection of up to 8
supervised inputs and 8 volt-free relay outputs.
Clearly labelled connectors simplify the task.
Overview Janus C4 IO16 Blade
Aux Inputs 5V pullup (2k2), max 12V in
Aux Out 30V, 3A max
External Power Out (power limited) 12V, 500mA max
Operating Temperature 0 to +49°C (32 to 120°F)
Humidity 5-85±5% at 30±2°C (86±4°F)
Weight 185 g
Dimensions 197 x 60 x 28 mm
Janus C4 I/O Blade
Installation Guide
janus
C4
JC4-ADV-BL-IO16
Electromagnetic Compatibility
Following the provisions of EMC Directive 2014/30/EU,
this product complies with the following standards:
EN 55022:2010 Class B
EN50130-4:2011 inc A1:2014
IEC 62599-2:2010
WEEE
Please refer to www.grosvenortechnology.com/
legal-info/ for disposal instructions under EU Directive
2012/19/EU.
Part number:
Page 2
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
GND
In +
GND
In +
GND
In +
GND
In +
GND
In +
GND
In +
GND
In +
GND
In +
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
I/O BLADE
0V
+12V
OUT
Auxiliary Input connections
The inputs are supervised and may optionally be used with line resistors for
fault detection.
Input
switch
1K
1K
GND
In +
1
Out NO
Com
Out NC
1
Normally Closed Contact
Common
Normally Open
The Auxiliary output relays oer volt free contacts and may be used to
connect to low voltage systems such as barriers or turnstiles, provided the
voltage across the contacts does not exceed 30V and current does not
exceed 3A.
Input switch
GND
In +
1
Contacts Only (no fault detection)
Supervised (short/open circuit detect)
Auxiliary Output connections
Inputs
1-8
Outputs
1-8
Power
out
The Aux input is pulled to 5V by the Blade using the equivalent circuit
shown below
Connections
Power supply
12Vdc power supply for
connecting associated
devices.
+
Power Out
12 Vdc
0V
+12V
OUT
Supervised (short/open circuit detect)
Tamper
switch
1K
1K 2K2
Input
switch
GND
In +
1
Supervised (short/open circuit detect)
Page 3
Power
The Janus C4 I/O Blade draws 12V power from the
Controller.
The I/O Blade Power draw is summed as follows:
I/O Blade Quiescent Current = 83 mA max @12V
(1.0W)
I/O Blade Maximum Current (all AUX Output Inputs
grounded, all AUX Output relays active) = 333 mA
@12V (4.0W)
External 12V output (if used) = up to 500 mA max
@12V (6.0W)
Notes
Blade LED indicators
Status LED
The main Blade LED Indicator is used to indicate activity
and state. See also the status LED on the controller.
If the LED is continuously red, the Blade is not
communicating with the controller.
Blade State is reported by ashing a code on the LED
every 15 seconds as follows:
5 blue ashes Board is not being monitored.
Probably no download to controller
from Janus C4
5 red ashes Wrong device type congured, e.g.
Door dened on an IO Blade
3 red ashes Out of range device congured
5 green ashes No devices congured for board
5 yellow ashes Reports electrical issues, such as
current tripped, over voltage, under
voltage, over current, under current
Blade Activity is reported as follows:
Yellow icker (lasts
about 30 seconds)
Firmware download in progress
Green blink (every 5
seconds)
Board running OK
Blue blink Read
Yellow blink Input state change
Red blink Output state change
Email: info@grosvenortechnology.com
Telephone: +44 (0)1279 838000
Web: www.grosvenortechnology.com
Page 4
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Janus Sistema I/O
Manuali Sistema I/O popolari di altre marche
WAGO
WAGO 750-344 Manuale utente
Teknim
Teknim TWM-1887 Manuale di istruzioni
Intelligent Appliance
Intelligent Appliance IA-2662-E Manuale utente
BERGHOF
BERGHOF ECC DIO 16/16 Manuale di istruzioni
Advantech
Advantech PCM-27J3AU Manuale di installazione e funzionamento
Festo
Festo CP-E08-M12-CL Manuale utente
