jbc FAE1-B Manuale utente
Fume Extractor
Ref. FAE1-B
INSTRUCTION MANUAL
www.jbctools.com
Fume Extractor
Ref. FAE1-B
www.jbctools.com
INSTRUCTION MANUAL
H13 Filter & Carbon Filter
& M5 Pre-filter ........................................... 1 unit
Ref. FAE1-100
*Already assembled
Packing List
The following items are included:
Fume Extractor ......................................... 1 unit
Ref. FAE1-1B (100V / 120V)
FAE1-2B (230V)
Unseal the filter
before the first use
Manual ................................................. 1 unit
Ref. 0023483
Power cable ........................................... 1 unit
Ref. 0009417 (100V / 120V)
0009401 (230V)
RJ12 direct cable ................................ 2 units
Ref. 0019751
RJ12-USB A adapter ........................... 1 unit
Ref. 0023504
USB A/B cable ..................................... 1 unit
Ref. 0021042
2
Features
Aspiration tubes for 1 workbench and up to 4 stands (1 work intake
configuration) or for 2 workbenchs (2 work intakes configuration).
Quick release
levers for filter
change
Power socket
Main switch
Process screen
USB-B connection Pedal connection
RJ12 station
connections
Filter saturation indicator
Green: Filter OK
Yellow: ≤ 20% carbon lifetime or about to saturate
Red: End of carbon lifetime or filter saturated
www.jbctools.com
3
FlowFlow
HML
Saturation 20%
FilterFilter
Carbon life 90%
Aspiration
ON
FlowFlow
Saturation 20% 100%
FilterFilter
Carbon life 90%
Aspiration
ON
Fume Extractor
Ref. FAE1-1B (100V / 120V)
FAE1-2B (230V)
Accessory for
stand aspiration
(up to 4 stands)
Ref. FAE040
To be assembled on
your workbench with
the included clamp
Ref. FAE030
To be assembled directly
on your workbench (hole
drilling required)
Stand
Aspiration Duct
Ref. FAE050
For modular stands
(From SD versions
onwards)
Ref. FAE060
For compact stations
(From B versions
onwards)
Flexible arm Ø50
Ref. FAE070
Lenght: 1 m (39.37 in)
To be assembled on
your workbench with
the included clamp
Ref. FAE020
To be assembled directly
on your workbench
(hole drilling required)
Flexible Hoses Ø50
Ref. FAE010
Lenght: 1,5 m
(59.05 in)
Connect the Fume Extractor
indifferently to the flexible
arm or to the accessory for
stand aspiration
Attention
Avoid awkward positions
in order to minimize
pressure losses
1 work intake configuration assembly (default configuration)
Main screen
Preset program screen Custom program screen
Troubleshooting
Station troubleshooting available on the product page at www.jbctools.com
High, medium and low
aspiration programs Aspiration status
Flow rate
4
20%
Saturation
Aspiration
ONON
Carbon life
80%
Fume Extractor
Ref. FAE1-1B (100V / 120V)
FAE1-2B (230V)
Flexible arms Ø50
Ref. FAE070
Lenght: 1 m (39.37 in)
To be assembled on
your workbench with
the included clamp
Flexible Hoses Ø50
Ref. FAE010
Lenght: 1,5 m
(59.05 in)
Connect the Fume
Extractor to the flexible arm
Attention
Avoid awkward positions
in order to minimize
pressure losses
2 work intakes configuration assembly (optional configuration)
Main screen
Troubleshooting
Station troubleshooting available on the product page at www.jbctools.com
Aspiration status
In this configuration aspiration at stand is not available, aspiration flow is set High. Note that in this
configuration, suction force per intake is decreased when compared to 1 work intake configuration (see
details on page 14). Change Work intakes parameter into 2 in order to set this configuration (see page
7).
Ref. FAE020
To be assembled directly
on your workbench
(hole drilling required)
www.jbctools.com
5
STOPSTOP ##44
Cover opened or badly
closed. Double check the
cover.
FlowFlow
HML
Saturation 20%
FilterFilter
Carbon life 90%
Aspiration
ON
FlowFlow
HML
Saturation 20%
FilterFilter
Carbon life 90%
Aspiration
ON
FlowFlow
Saturation 20% 100%
FilterFilter
Carbon life 90%
Aspiration
ON
20%
Saturation
Aspiration
ONON
Carbon life
80%
If the display shows STOP#4, power off the fume extractor, remove the cover, place it back and
secure it using the quick release levers.
Menu Interface
Main Screen
Main screen may vary according to the Work intakes and Program parameters. For 1 work intake
configuration the aspiration flow can be changed by keys, whereas for 2 work intakes configuration
the flow cannot be changed.
Change the aspiration
Custom level and the
aspiration Preset program.
Turning on the fume extractor
Once the fume extractor is turned on, the display shows a similar screen as the following one and
the filter saturation indicator is green if the carbon lifetime is higher than 20%.
Troubleshooting
Station troubleshooting available on the product page at www.jbctools.com
1 work intake configuration12 work intakes configuration2
6
PortPort
1 Pedal
BackBack
4 Filter set
5 Counters
6 Program version
Main menuMain menu
Exit
1 Reset
2
Unit
3
Port
UnitUnit
1 Continuous mode OFF
2
Beep ON
3 PIN OFF
4 Change PIN
Filter setFilter set
1 Carbon life 90%
2 Saturation 20%
3 Reset carbon
BackBack
CountersCounters
1 Total
2 Partial
BackBack
PortPort
1 Program Ctm - 100%
2
Delay to stop
3
Pedal
BackBack
Total CountersTotal Counters
1 Plugged hrs 100
2 Idle hrs 10
3 Work area hrs 70
4 Stand hrs 20
5 Work area cys 10
BackBack
Partial CountersPartial Counters
1 Plugged hrs 100
2 Idle hrs 10
3 Work area hrs 70
4 Stand hrs 20
5 Work area cys 10
6 Reset
BackBack
5 Work intakes 1
BackBack
Menu Interface
Main menu parameters
Original PIN: 0105
1 work intake configuration12 work intakes configuration2
Not available for
2 work intakes
configuration
www.jbctools.com
7
Delay to stopDelay to stop
1 Stand 30 sec
BackBack
PedalPedal
1 Activation One-touch
2 Mode Pressed
BackBack
Custom programCustom program
Select work area flow
80 %
PortPort
1 Program Ctm - 100%
2
Delay to stop
3
Pedal
BackBack
PortPort
1 Program Ctm - 100%
2
Delay to stop
3
Pedal
CustomCustom
BackBack
PortPort
1 Pedal
BackBack
PedalPedal
1 Activation One-touch
2 Mode Pressed
BackBack
Menu Interface
1Port menu 1 work intake configuration
OK
2Port menu 2 work intakes configuration
8
Parameters
Important: Power off any Station or Device connected to the fume extractor before
modifying any parameter.
Unit
Parameter Description
Continuous mode
Enable/disable continuous aspiration. When enabled, fume extractor
suction is activated. Aspiration remains active until continuous mode is
disabled or the equipment is powered off.
By default Continuous mode is OFF.
Beep
Enable/disable the sound of the keypad.
By default Beep is ON.
PIN
Enable/disable PIN request when modifying parameters.
By default PIN is ON.
Change PIN
Change the default security PIN code.
By default the PIN is 0105.
Work intakes
It sets how many intakes will work as workbench extractions. The options
are 1 and 2.
By default Work intakes is 1.
www.jbctools.com
9
Port
Parameter Description
Program
It sets the fume extractor aspiration flow. You can select between Preset
and Custom aspiration programs.
H (High), M (Medium) or L (Low) are the three Preset available options.
Use Up and Down keys to switch between them while being on the main
screen.
Up to ten aspiration levels between H (High) and L (Low) can be selected
for Custom program (range 10-100%). If a Custom aspiration program
is selected, the selected aspiration level can be changed on the main
screen.
By default M (Medium) aspiration program is selected.
Delay to stop /
Stand
It sets the time that a fume extractor keeps aspirating fumes at the stand
once the tool is returned to it (range 0-999 seconds)
By default Stand time is 60 seconds.
Pedal / Activation
It sets the pedal activation mode.
One-touch: Press the pedal once to activate aspiration. Press again to
stop aspiration.
Pressed: (Mode function must be Pressed) aspiration is active as long as
the pedal is kept pressed.
By default Activation is Pressed.
Pedal / Mode
When the activation parameter is set to Pressed, the Mode parameter can
be configured to Released mode. In this mode aspiration is always active
until the pedal is pressed.
By default Mode is Pressed.
10
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali jbc Scrubber
