JCM GOLD GP-965 Manuale utente

GP-965 SLIP PRINTER

USER’S MANUAL

JCM GOLD (H.K.) LTD.

Oct, 2000

GP-965 USER’S MANUAL2

PREFACE

Thank you for purchasing this Slip Printer. Please read this manual carefully before operating your slip printer and keep

it at hand for future reference. We hope it will be helpful to you if you encounter any operational problem.

The information in this manual is subject to change without notification. Further pages may be added to future editions.

The user is asked to excuse any omissions or error in the present edition. No liability will be assumed for any changes,

omissions, or error, in this manual, or for any accidents that occur while the use is following the instructions in it.

No liability will be assumed for defects in the slip printer’s firmware.

BEFORE OPERATION THE SLIP PRINTER

General Precautions

lThe shock of impact can damage the slip printer. Install the slip printer on a stable and level place.

lDo not move the slip printer with the power ON.

lBe careful not to spill liquids on the slip printer, or drop metallic objects such as paper clips into it.

lTo clean the slip printer, wipe it with a soft, dry cloth, Do not use solvents such as thinner, lcohol or benzene.

lIf you leave the slip printer unused for a long time, unplug the power cord.

lPlease pay attention to the following notes for the operation of the slip printer.

Power on: Turn on the power of ECR first, then power on the slip printer.

Power off: Turn off the power of the slip printer first, then power off ECR.

Operation message: While operation the slip printer, if the slip printer has paper, but ECR display the message

that slip printer has no paper, please turn off the power of the slip printer, then turn on it again.

Choosing a Location for the Slip Printer

Avoid location where the slip printer would be exposed:

lExcessive dust

lVibration

lHigh humidity

lExtremely high or low temperature rapid changes in temperature

lDirect sunlight

lDirect heat from a heating appliance.

NOTICE

FOR PLUGGED EQUIPMENT, THAT THE SOCKET –OUTLET SHALL BE INSTALLED NEAR

THE EQUIPMENT AND SHOULD BE EASILY ACCESSIBLE.

CAUTION

Do not use this slip printer outdoors in the rain or near any source of liquid.

GP-965 USER’S MANUAL3

Things to Check when Unpacking

The GP965 Slip Printer consists of following part and manual. When unpacking, check to see if your GP965 Slip Printer

contains all of these items.

Item Product name and type Quantity

1 GP965 Slip Printer 1

2 Power Code Black (H05VVF 0.75/3C, 1.8M) 1

3 ERC-27 Ribbon Cassette (Purple) 1

4 Dust Cover 1

5 Serial port Communication Cable 1

6 GP965 Slip Printer User’s Manual (this manual) 1

7 Parallel port Communication Cable (option) 1

If any of these items are missing or found faulty, please contact your distributor. Also, if there is any question or doubt

about the packaged product, contact your distributor.

GP-965 USER’S MANUAL4

CHAPTER 1

GENERAL DESCRIPTION

1.1 General Features

Compact, space efficient design

Functions and software control features include:

lIt can be used as a general serial terminal printer

lMultiple character sizes (standard, double width)

lForward and backward paper feeding

lPaper eject function

lTOF and BOF detection

1.2 General Specifications

1.2.1 Printer Mechanism

lPrinting method: 7-pin, shuttle impact dot-matrix

lPrinting width: 65.84mm, 210 dots

lPrinting words: 35 characters/line

lCharacter set: 96 ASCII characters and multiple international characters

lCharacter size: 1.6mm(W)¡Á2.9mm(H) at 5¡Á7 font (3.2mm(W)¡Á2.9mm(H) at 5¡Á7 font, enlarged)

lColumn spacing: 0.63mm(5¡Á7 font) (1.26mm for 5¡Á7 font, enlarged) is the default value

lPrinting speed: Approx. 2.3 LPs (5¡Á7 font, 3 dot line spacing)

lLine spacing: 4.23mm (1/6 inch)

lPaper feed speed: Approx. 25 lines/sec (105mm/s)

lPaper release: Release by operator panel switch

lPaper backward: Backward by operator panel switch

lLED display when power turn on

1.2.2 Paper

lPaper types: Normal paper (high quality), pressure sensitive paper, carbon copy paper

lTotal thickness: 0.09mm to 0.35mm

lDimensions: 80mm(W)¡Á80mm(L) to 182mm(W)¡Á257mm(L), Up to European B5 size

lCopy capability and paper thickness:

1) Single sheet (No copies) 0.09mm to 0.25mm

2) Combination of normal paper and pressure sensitive paper

3 sheets maximum (1 Original + 2 copies)

Back paper: 0.07mm to 0.20mm

Copy paper, original paper: 0.04mm to 0.07mm

Carbon copy paper: Approx. 0.035mm

1.2.3 Inking

lInking method: Exclusive ribbon cassette

lColor: Purple

lCassette dimensions: Approx. 115mm(W)¡Á42.0mm(D)¡Á22mm(H)

lLife expectancy: Approx. 1.5million characters

GP-965 USER’S MANUAL5

lType: EPSON ERC-27

1.2.4 Power Supply: AC 100V to 240V, 50Hz or 60Hz

1.2.5 Power Consumption:

lOperating: Approx. 150mA at AC 240V, or 500mA at AC 100V

lNon-operating: Approx. 15mA at AC 240V, or 40mA at AC 100V

1.2.6 Temperature:

lOperating: 0 to 40'C

lStorage: -10 to 50'C

1.2.7 Reliability:

lMCBF: 1.5 million lines

lPrint head life: Approx. 100 million strokes/pin

1.3 Interface

1.3.1 Parallel interface (Option)

1.3.1.1 General Specification

lSpecification

Data format: 8-bit parallel

Synchronization: STROBE pulse from the host computer

Handshaking Timing: ACKNLG and BUSY signals

Signal level: TTL compatible.

lInterface Connector: 36pin plug or equivalent

lPin Assignment

Signal Pin Return Signal Direction

119 STROBE Host machine

220 DATA1 Host machine

321 DATA2 Host machine

422 DATA3 Host machine

523 DATA4 Host machine

624 DATA5 Host machine

725 DATA6 Host machine

826 DATA7 Host machine

927 DATA8 Host machine

10 28 ACKNLG Printer

11 29 BUSY Printer

12 30 PE Printer

13 SLCT Printer

14 NC

15 NC

16 GND

17 CHASSIS GND

18 NC

19-30 GND

31 NC

32 NC

33 GND

34 NC

GP-965 USER’S MANUAL6

35 +5V Printer

36 NC

NOTES:

l"Return Side" denotes the Twisted-pair return, to be connected to signal ground. For interface wiring, be sure to use

a twisted-pair cable for each signal and complete the connection on the return side. To prevent noise, these cables

should be shielded and connected to the chassis of the host computer.

lAll of the interface conditions are TTL. The rising time and falling time of any signal should be 0.2us or less.

lNever transmit data without checking ACKNLG and BUSY. (Data should only be transmitted to this printer after

confirming that ACKNLG is active, or when BUSY is "LOW".)

lThe interface cable should be as short as possible.

1.3.1.2 Timing chart£º

BUSY

/ACK

5us 5us

DATA

/STB

0.5us(min)

GP-965 USER’S MANUAL7

1.3.2 Serial interface

1.3.2.1 Specification

lCommunication Speed: 9600bps, 4800bps, 2400bps, 1200bps, DIP Switch select (on the bottom of the printer case)

lSynchronizing method: Synchronous

lHandshaking: XON/XOFF

lData format: 1 start-bit, 8-bit data, non check bit, 1 stop-bit

lSignal level: ON (SPACE) = 3V to 12V, OFF (MARK) = -3V to -12V

1.3.2.2 Connector: D-Sub connector 25pin (DB-25S)

PIN No. SIGNAL DESCRIPTION DIRECTION

1FG Chassis GND

2TD Transmitted Data Output

3RD Receiving Data Input

4CTS Clear Transmit Input

5RTS Requisition Transmit and Paper Empty Output

7S.G Signal GND

Notes:

lOutput: from GP-965 slip printer to host

lInput: from host to GP-965 slip printer

1.3.2.3 Timing signal

35 characters More than 35 characters

RXD FROM HOST DATA DATA DATA

DC3 DC1 NAK DC3 DC1 DC3

TXD TO HOST

Have paper

Printing Printing

No paper

RTS

GP-965 USER’S MANUAL8

Notes:

lLF: 0AH

lDC1: 11H

lDC3: 13H

lNAK: 15H

1.4 DIP Switch function and set

1.4.1 DIP Switch (on the bottom of the printer case)

The DIP settings are read and become effective only when the power is turned on or when the printer is reset. Therefore,

changing the settings while the power is on will not have any effects.

1.4.2 DIP Switch function and setting

DIP Switch function and set£¨ on the bottom of the printer case£©

BAUD SET BUTTON

WORKING OR NOT

WORKING SELECT

CHARACTER

TABLE SELECT

PARALLEL OR SERIAL PORT

SELECT

DIP1 DIP2 BAUD

(BPS)

DIP3

BUTTON DIP4

CHARACTER

TABLE DIP7 DIP8 PORT

OFF OFF 9600 OF

WORKING OFF 1 OFF OFF PARALLEL

OFF ON 4800

NOT

WORKING

ON 2 ON ON SERIAL

ON OFF 2400

ON ON 1200

Notes£º

lDIP5 and DIP6 not use.

lCharacter table 1 is JAPAN character, character table 2 is ITALY character.

1.5 The machine system is installed and operated

1.5.1 Back panel

POWER£º100V to 240V power socket

SERIAL£ºSerial port socket

PARALLEL: Parallel port socket (option)

POWER SERIAL PARALLEL

GP-965 USER’S MANUAL9

1.5.2 Front panel SW and operate

lPOWER LED£¨RED£©

Light: Power is turned on

Dark: Power is turned off

lButton function

Press RELEASE, release paper

Press REVERSE, eject paper to backward

Press RELEASE and REVERSE, then turn on power, itself check

After turn on power, press RELEASE and REVERSE, reset

POWER

RELEASE

REVERSE

GP-965 USER’S MANUAL10

1.6 Control Codes and Functions

1.6.1 CR

Name: Carriage Return

Code: 0DH

Function: This code is same as LF.

1.6.2 LF

Name: Line Feed

Code: 0AH

Function: When this code is received, the data in the buffer is printed and the paper is advanced one line.

If there is no printable data preceding this code, or if all codes before this code are space codes, this code advances the

paper one line without printing anything.

Line spacing is 1/6 inch.

1.6.3 FP

Name: Form Feed

Code: 0BH+n (1<=n<=20)

Function: Rapid Paper Feeding is generated after printing for one line by inputting Parameter Data after this code (Rapid

Paper Feed Code). It will be read 20 in the memory when the data comes 20 or over 20. In case of zero “0” on data, it

will be read as “1”.

1.6.4 HP

Name: Head Position

Code: 13H+n (1<=n<=32)

Function: The Head Position including the Space code by inputting Parameter Code after this code can be generated. In

case of 32 and over 32 on Parameter or Print Buffer Data, it will be set on 32.

1.6.5 PR

Name: Paper Release Code

Code: 12H

Function: Paper Release Code. After printing for one line, the paper can be released by inputting this code. Over 29

digits one printing can not be allowed for one line.

1.6.6 CAN

Name: Cancel Code

Code: 18H

Function: Cancel Code. Clearing out all memory for one line from Print Buffer by inputting this code.

1.6.7 LC

Name: Set enlarged printing

Code: 11H+n (32<=n<=255)

Function: Large Character Code. The character of data code following this code can be enlarged. Data code from 00H to

1FH will be regarded as the space. This code is released at every character.

Altri manuali per GP-965

Indice

Altri manuali JCM GOLD Stampante

JCM GOLD

JCM GOLD GP-965 Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente