Jireh SKOOT HT Manuale utente
SKOOT
Automated Scanner
HT
DP0029 Rev 00.6
PAGE i of viii DP0029 Rev 00.6
SAFETY WARNINGS / PRECAUTIONS
DANGER! The SKOOT HT is designed for a specic use. Using
the SKOOT HT outside of its intended use is dangerous. Failure to comply
with the warnings, instructions, and specications in this manual could
result in SEVERE INJURY or DEATH. Read and understand this manual
before using.
KEEP THIS MANUAL – DO NOT LOSE
THIS MANUAL IS PART OF THE SKOOT HT SYSTEM AND MUST BE RETAINED FOR
THE LIFE OF THE PRODUCT. PASS ON TO SUBSEQUENT OWNERS.
Ensure any amendments are incorporated with this document.
DANGER! FALLING OBJECT HAZARD. The area below a
crawler must be kept clear at all times. A clearly marked NO ENTRY
ZONE must be cordoned off directly below the area of crawler operation.
(see No Entry Fall Zone on page 66 for additional details)
DANGER! Do NOT operate or place crawler on a surface higher
than 2 m (6 ft) without a proper tether held taut at all times.
(see Tether Requirements and Attachment on page 67 for additional details)
DANGER! ELECTRICAL CORDS CAN BE HAZARDOUS. Misuse
can result in FIRE or DEATH by ELECTRICAL SHOCK. Inspect
thoroughly before each use. Do NOT use if damaged. Do NOT use when
wet. Keep away from water. Do NOT drive, drag or place objects over
cord.
WARNING! Do NOT operate scanner in an explosive
environment. Do NOT operate scanner in the presence of volatile
substances.
PAGE ii of viii
WARNING! HOT SURFACE. The SKOOT HT crawler may reach
temperatures that may cause burns if contacted with bare skin. Wear heat
resistant safety gloves when handling.
WARNING! MAGNETIC MATERIAL. The wheels of the crawler
produce an extremely strong magnetic eld which may cause failure or
permanent damage to items such as watches, memory devices, CRT
monitors, medical devices or other electronics.
Tools, magnets and metal objects can cut, pinch or entrap hands and
ngers. HANDLE WITH CARE.
People with pacemakers or ICD’s must stay at least 25 cm (10 in) away.
CAUTION! Pinch points exist with this product. Keep ngers and
hands clear of pinch points.
CAUTION! DO NOT operate the SKOOT HT crawler on an
inspection surface which is electrically connected to a component that is
being welded.
WARNING! The coolant used in this product contains a 50/50
blend of ethylene glycol based automotive antifreeze and water. Consult the
MSDS for hazards associated with the use and handling of this coolant.
WARNING! FLAMMABLE. The coolant used in this product
contains a 50/50 blend of ethylene glycol based automotive antifreeze and
water. This uid is ammable if heated to greater than 110°C and ignited
with an external ignition source. If a leak develops, keep ignition sources
away from coolant vapors. Also, the uid will auto ignite if heated to
temperatures greater than 410°C (770°F). Do not use system on surfaces
>350°C (662°F).
PAGE iii of viii DP0029 Rev 00.6
The WEEE symbol indicates that the product must not be disposed of as
unsorted municipal waste, but should be collected separately.
(see Disposal on page 122 for additional details).
NOTE: The above safety warnings highlighted in white are labelled on the products.
CAUTION! Do not disconnect under load. Shut off power before
connection or disconnecting. Permanent damage to electronics could occur.
Emergency Stop. This symbol indicates emergency stop button.
PAGE iv of viii
Chapter1 Identification 1
1.1. Product Brand 1
1.2. Manufacturer 1
1.3. Compliance Declarations 1
1.3.1. European Union CE Declaration 1
1.3.2. FCC 1
1.3.3. Industry Canada 2
Chapter2 Product Specifications 3
2.1. Intended use 3
2.1.1. Operating Limits 4
2.1.2. Operating Environment 4
2.1.3. User 4
2.2. Unintended Use 5
2.3. Dimensions and Weight 6
2.4. Power Requirements 7
2.5. Environmental Sealing 7
2.6. Performance Specifications 8
2.7. Encoder Interface Specifications 8
Chapter3 Definitions 9
3.1. Definitions of Symbols 9
Chapter4 System Components 10
4.1. Component Identification 10
4.2. Tools 13
4.2.1. Included Tools 13
4.2.2. Optional Tools 13
Chapter5 System Components 14
TABLE OF CONTENTS
PAGE v of viii DP0029 Rev 00.6
5.1. Handheld Controller 14
5.2. Crawler 15
5.2.1. Swivel Mount 16
5.2.2. Umbilical 17
5.2.3. Handle 17
5.2.4. Emergency O Button 18
5.2.5. Cable Retainer 18
5.2.6. Manipulation Handle 19
5.2.7. Quick Connect Fitting 19
5.3. Raster Arm HT 20
5.3.1. Mounting a Raster Arm HT 21
5.3.2. Raster Arm HT Cable Setup 22
5.3.3. Quick Connect Fitting 24
5.4. Probe Holder Attachments 25
5.4.1. Heavy Duty Vertical Probe Holder 25
5.4.1.1 Probe Holder Setup 25
5.4.1.2 Probe Holder Vertical Adjustment 27
5.4.1.3 Probe Holder Left/Right Conversion 28
5.4.1.4 Probe Holder 90° Adjustment 29
5.4.2. Two Probe Raster Arm HT 30
5.4.3. Corrosion Thickness Probe Holder 31
5.4.4. Raster Arm HT Cable 33
5.5. Power Controller 34
5.6. Auxiliary Cable 36
5.7. Encoder Cable 36
5.8. Vertical Probe Holder 37
5.8.1. Probe Holder Setup 37
5.8.2. Probe Holder Vertical Adjustment 38
5.8.3. Probe Holder Transverse Adjustment 39
5.8.4. Probe Holder Longitudinal Adjustment 40
5.8.5. Probe Holder Left/Right Conversion 41
5.9. Slip Joint Probe Holder 43
5.9.1. Probe Holder Setup 43
5.9.2. Probe Holder Adjustment 45
5.9.3. Probe Holder Force Adjustment 45
5.9.4. Slip Joint Probe Holder Left/Right Conversion 47
5.10.Low Profile Probe Holder Frame 49
5.10.1. Low Profile Probe Holder Frame Setup 49
5.11. Probe Holder Frame 52
5.11.1. Probe Holder Frame Setup 52
5.12.Pivoting Probe Holder Frame 55
PAGE vi of viii
5.12.1. Mounting a Pivoting Probe Holder Frame 56
5.12.2. Pivoting Probe Holder Frame Setup 57
5.12.2.1 Longitudinal Scanning 57
5.12.2.2 Circumferential Scanning 58
5.12.2.3 Flange Scanning 59
5.13.HT Cable and Hose Management 62
5.13.1. Mounting the HT Cable Management 62
5.13.2. Cable Management Setup 63
5.13.3. Clamp Setup 64
5.13.4. Hose Connection and Routing 64
Chapter6 Preparation for Use 66
6.1. Transportation 66
6.2. Safety Precautions Before Use 66
6.2.1. No Entry Fall Zone 66
6.2.2. Tether Requirements and Attachment 67
6.3. Preparation of Inspection Surface 68
6.4. Configurations 69
6.4.1. Crawler with Raster Arm HT 69
6.4.2. Crawler with Probe Holder Frame 71
Chapter7 Operation 73
7.1. System Startup 73
7.2. Placement of Crawler on Inspection Surface 75
7.3. Removal of Crawler from Inspection Surface 77
7.4. Operation 79
7.4.1. Handheld Controller Layout 79
7.4.1.1 Touchscreen 80
7.4.1.2 Click Wheel 80
7.4.1.3 Joysticks 80
7.4.2. Main Mode Selection Screen 80
7.4.3. Jog Mode 81
7.4.4. Latched Jog Mode 83
7.4.5. 2 Axis Scan Mode 83
7.4.5.1 2 Axis Scan Setup Screen 84
7.4.5.2 Scan Speeds Screen 85
7.4.5.3 2 Axis Scan Screen 86
7.4.6. Cooler Mode 88
7.4.7. Cooler Warnings 90
7.4.8. System Utilities Screen 91
7.4.8.1 User Settings Screen 91
PAGE vii of viii DP0029 Rev 00.6
7.4.8.2 Diagnostics Screens 92
7.4.8.2.1. Detected Modules 93
7.4.8.2.2. System 1 93
7.4.8.2.3. System 2 94
7.4.8.2.4. System 3 94
7.4.8.2.5. Skoot-L, Raster 95
7.4.8.3 Touch Calibration Screen 96
7.4.8.4 Joystick Calibration Screen 96
7.4.8.5 Draw 97
Chapter8 Maintenance 98
8.1. Safety Precautions Before Maintenance 98
8.2. Maintenance Schedule 99
Chapter9 Troubleshooting 100
9.1. Technical Support 100
9.2. Startup Issues 100
9.2.1. Joystick O Center 100
9.2.2. Checking Network 101
9.3. Startup Override 101
9.3.1. Scan Devices 102
9.3.2. Reset Parameters 103
9.3.3. System Parameters 103
9.3.4. Device Address 103
9.4. Additional Issues 104
9.5. Retrieval of a Stranded Crawler 105
Chapter10 Service and Repair 106
Chapter11 Spare Parts 107
11.1. SKOOT HT Crawler 107
11.2. SKOOT HT Kit Components 108
11.2.1. Encoder Connector Type 109
11.2.2. Power Cord Type 109
11.3. Raster Arm HT Module 110
11.4. Hose Spare Parts 111
11.5. Probe Holder Frame 112
11.6. Low Profile Probe Holder Frame 113
11.7. Pivoting Probe Holder Frame 114
PAGE viii of viii
11.8. Slip Joint Probe Holder Parts 115
11.9. Vertical Probe Holder Parts 116
11.10.Heavy Duty Vertical Probe Holder 117
11.11. Corrosion Thickness Probe Holder 118
11.12.Probe Holder Components 119
11.12.1. Arm Style 119
11.12.2. Yoke Style 119
11.12.3. Swing Arm Style 119
11.12.4. Heavy Duty Yoke Style 119
11.12.5. Pivot Button Style 119
11.13.Variable Components 120
11.13.1. Frame Bar 120
11.13.2. HT Cable Management Sleeving 120
11.14.Cases 121
Chapter12 Disposal 122
Chapter13 Limited Warranty 123
PAGE 1 of 124 DP0029 Rev 00.6
Chapter 1
IDENTIFICATION
1.1. Product Brand
The SKOOT HT is a remotely operated vehicle with magnetic wheels suitable for
driving on ferrous material. Its primary purpose is to move inspection equipment over
areas of structures, such as tanks or pipes, made from ferrous materials in industrial
environments.
1.2. Manufacturer
1.3. Compliance Declarations
1.3.1. European Union CE Declaration
Jireh Industries hereby declares that the SKOOT HT product
complies with the essential requirements and other relevant
provisions of the following European Union directives:
2014/30/EC EMC Directive
2014/30/EC Low Voltage Directive
2012/19/EU Directive on Waste Electrical and Electronic Equipment
1.3.2. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
DISTRIBUTOR:
Jireh Industries Ltd.
53158 Range Road 224
Ardrossan, Alberta, Canada
T8E 2K4
Phone: 780.922.4534
jireh.com
MANUFACTURER:
Altri manuali per SKOOT HT
1
Indice
Altri manuali Jireh Scanner
Jireh
Jireh Rotix Manuale utente
Jireh
Jireh Microbe Manuale utente
Jireh
Jireh Rotix Manuale utente
Jireh
Jireh ODI-II Manuale utente
Jireh
Jireh Microbe Manuale utente
Jireh
Jireh STIX Manuale utente
Jireh
Jireh NAVIC 2 Manuale utente
Jireh
Jireh Rotix Manuale utente
Jireh
Jireh NAVIC Manuale utente
Jireh
Jireh Rotix Manuale utente
Jireh
Jireh STIX Manuale utente
Jireh
Jireh Skoot Manuale utente
Jireh
Jireh STIX Manuale utente
Jireh
Jireh ROTIX CE0142 Manuale utente
Jireh
Jireh STIX Manuale utente
Jireh
Jireh Circ-it Manuale utente
Jireh
Jireh Skoot Manuale utente
Jireh
Jireh SKOOT HT Manuale utente
Jireh
Jireh Rotix Manuale utente
Jireh
Jireh Rotix Manuale utente
