Johnson Controls VFD67 Series Manuale utente

24-10511-7

www.johnsoncontrols.com

1 Operate the VFD67 drive from the keypad

Keypad mode is used to operate the drive completely from the keypad. This is the default setting of the VFD67 and this procedure is written as the drive would

be delivered from the factory.

STEP 1: (required) Ensure the control signals B2, B4, B5, and B6 are DISCONNECTED. (Drive modes will not change if these control signals are connected).

STEP 2: Wire the mains and motor, and power the drive (See Figure 1).

STEP 3: Use the MODE key in combination with the UP and DOWN keys on the keypad to set parameters 1 to 4 for the desired frequency limits

and ramp values. (See front cover of the VFD67 drive for parameter descriptions).

STEP 4: Set Pr 05 to PAd (default setting).

STEP 5: Set Pr 06 to motor rated current.

STEP 6: Press the MODE key button (2 times) on the keypad until is displayed.

STEP 7: Close or jumper terminal B2 to B4. (See Figure 2). Display will change from to

STEP 8: Press the green START key on the drive keypad to run the drive (The display will read and the motor will be at zero speed).

STEP 9: Press the UP key to increase the speed, press the DOWN key to decrease the speed. The STOP/RESET key is used to stop and reset the

drive.

2 Operate the VFD67 drive with a 0 to 10Vdc control signal

STEP 1: (required) Ensure the control signals B2, B4, B5, and B6 are DISCONNECTED. (Drive modes will not change if these control signals are connected).

STEP 2: Wire the mains and motor, and power the drive (See Figure 1).

STEP 3: Use the MODE key in combination with the UP and DOWN keys on the keypad to set parameters 1 to 4 for the desired frequency limits

and ramp values. (See front cover of the VFD67 drive for parameter descriptions).

STEP 4: Set Pr 05 to (this is the analog voltage mode).

STEP 5: Set Pr 06 to motor rated current.

STEP 6: Wire the control terminals (See Figure 3).

3 Operate the VFD67 drive with a 4-20mA control signal

STEP 1: (required) Ensure the control signals B2, B4, B5, and B6 are DISCONNECTED. (Drive modes will not change if these control signals are connected).

STEP 2: Wire the mains and motor, and power the drive (See Figure 1).

STEP 3: Use the MODE key in combination with the UP and DOWN keys on the keypad to set parameters 1 to 4 for the desired frequency limits

and ramp values. (See front cover of the VFD67 drive for parameter descriptions).

STEP 4: Set Pr 05 to (this is the analog current mode).

STEP 5: Set Pr 06 to motor rated current.

STEP 6: Wire the control terminals (See Figure 4).

VFD67 Quick Start Commissioning:

24-10511-7

www.johnsoncontrols.com

Figure 1 Power terminal connections

Figure 2 Keypad operation Figure 3 0 to 10Vdc operation

Figure 4 4 to 20mA operation

Optional ground

connection

Supply

ground

Optional

EMC filter

Optional

line reactor

Fuses

Mains supply

L3/N* U V WL1 L2**

PE PE***

Internal

EMC filter

Start/

Reset

Braking

resistor

Optional

Thermal

protection

device

Stop

* Not applicable on size A

** On size A this is L2/N

*** The other PE terminal can

be used for connecting cable

shields to ground if required

T2T3T4

B2B3B4B5B6B7

+24Vdc output (100mA)

Drive Enable/Reset

T = Top row

B = Bottom row

T2T3T4

B2B3B4B5B6B7

+24Vdc output (100mA)

T = Top row

B = Bottom row

Remote speed

ref input

Optional external

24V power supply

Open = Stop

Closed = Run

0 to 10Vdc analog input

Common

T2T3

B2B3

B5B6

+24Vdc output (100mA)

T = Top row

B = Bottom row

Remote speed

ref input

Open = Stop

Closed = Run

Common

4 to 20mA analog input

Optional external

24V power supply

Altri manuali per VFD67 Series

Indice

Altri manuali Johnson Controls Azionamento CC

Johnson Controls

Johnson Controls VFD66 Series Manuale utente

Johnson Controls

Johnson Controls Penn VFD68D Series Manuale di servizio

Johnson Controls

Johnson Controls VA-707 Series Manuale utente

Johnson Controls

Johnson Controls VFD-2DS-234HE-2 Guida

Johnson Controls

Johnson Controls VSD Series Manuale utente

Johnson Controls

Johnson Controls York AYK550 Manuale utente

Johnson Controls

Johnson Controls VFD67 Series Manuale utente

Johnson Controls

Johnson Controls VFD66JCB-1 Manuale utente

Johnson Controls

Johnson Controls Frick vyper VYA PG -46 Manuale utente

Johnson Controls

Johnson Controls PENN VFD68 Manuale utente

Johnson Controls

Johnson Controls PENN VFD68 Manuale utente

Johnson Controls

Johnson Controls VSD II Series Istruzioni per l'installazione e il funzionamento

Johnson Controls

Johnson Controls VSD II Series Manuale utente

Johnson Controls

Johnson Controls YORK HYP1100A Manuale utente

Johnson Controls

Johnson Controls VFD67 Series Manuale utente

Johnson Controls

Johnson Controls VFD Series Guida

Manuali Azionamento CC popolari di altre marche

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuale utente

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuale elenco delle parti

Chamberlain Garog

Chamberlain Garog D Series Manuale utente

Parker

Parker PDS Series Manuale utente

Festo

Festo DGC G Series Guida all'installazione

Binks

Binks QS-5012-1-CE Manuale utente

Danfoss

Danfoss VLT 2800 Series Scheda tecnica

ABB

ABB ACQ580-01 Series Manuale di installazione

YASKAWA

YASKAWA CANopen SI-S3 Manuale utente

GE D20A6 Manuale utente

Unex

Unex MC-D-250-1000-050W-TW Manuale utente

Geckodrive

Geckodrive G213V Manuale utente

ABB

ABB RSYC-01 Manuale utente

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuale del proprietario

WEG

WEG DeviceNet CFW500 Manuale utente

Siemens

Siemens SINAMICS G Scheda tecnica

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Istruzioni operative

SOMFY

SOMFY JR RU 30 Manuale utente