Johnson Controls FT-04A Manuale utente

FT-04A Quick Start Guide

Overview

This quick start guide provides the basic information you

need to mount and install the FT-04A.

Figure 1: FT-04A front view

Callout Description

1 Hot (H) and Ground (G) terminals

Analog output (AO) 1 and COM terminal2

AO2 and COM terminal

Universal input (UI) 1 and COM terminal3

UI2 and COM terminal

4 Undesignated terminal

FT-04A dimensions

See the following figure for the dimensions of the FT-04A.

Figure 2: FT-04A dimensions, mm (in.)

Parts included

• Five FT-04A controllers

• One pack sheet

Required tools and parts

One small flathead screwdriver to secure the wires to the

terminal blocks.

Mounting guidelines

Do not mount the controller in a location with any of the

environmental disturbances listed in Mounting locations

to avoid.

Mounting locations to avoid

• Areas with excessive moisture, corrosive fumes, or

explosive vapors

• Locations where excessive vibration or shock occurs

• Locations with excessive electrical noise, such as large

magnetic interference or variable speed drive modules

Optional mounting accessories

The EIO-FT-Clip is a mounting bracket that you can attach

to the bottom of the EasyIO FT-04 controller. See Figure 3

for dimensions of the EIO-FT-Clip.

LIT-12014187 Version 1.0

2023-07-27

EASYIO-FT-04A

Figure 3: EIO-FT-Clip dimensions, mm (in.)

Attaching the FT Clip to any FTseries

controller

1. Align the FT-04A controller unit slots with the FT

Clip mounting bracket.

2. Lock the mounting bracket into position.

Figure 4: Attaching the mounting bracket

Detaching the FT Clip from any FT series

controller

1. Hold the FT-04A controller in one hand and the FT

Clip in the other hand.

2. Pull apart the FT-04A controller from the FT clip.

Figure 5: Detaching the FT Clip

Removing the FT-04A cover

1. To unlatch the casing, hold the sides of the cover

firmly between your thumb and finger and squeeze

gently.

FT-04A Quick Start Guide2

2. Remove the cover gently.

Figure 6: Removing the cover

Input, output, and 24 VAC Class

2 transformer power input wiring

diagrams

WARNING

Risk of Electric Shock

Disconnect the power supply before you make

electrical connections. Contact with components

carrying hazardous voltage can cause electric shock

and may result in severe personal injury or death.

NOTICE

Risk of Property Damage.

Do not apply power to the controller before checking

all wiring connections. Short circuited or improperly

connected wires may result in permanent damage to

the equipment.

Important

Do not exceed controller electrical ratings, this can

result in permanent damage to the controller and void

warranties.

Important

Only use copper conductors. Wire the controller

in accordance with local, national, and regional

regulations

Important

Use the correct electrostatic discharge precautions

throughout installation, setup, and service to avoid

damage to the controller and controller components.

FT-04A basic input, output, power and

serial device wiring setup

WARNING

Class 2 devices wiring only – do not reclassify and

install as class 1, 3 or power and lighting wiring.

FT-04A Quick Start Guide 3

Figure 7: FT-04A wiring guide

Callout Description

1 Input power, 24 VAC or 24 VDC

2 Voltage-controlled actuator

3 Voltage transmitter, 1 V to 10 V or 0 V to 5 V

4 Thermistor, RTD, or potentiometer

Figure 8: 24 VAC Class 2 transformer power input

Callout Description

1 20 AWG copper stranded wire

2 Controller

3 H terminal

4 G terminal

Figure 9: Analog output wiring

Callout Description

1 Field device

2 22 AWG copper stranded twisted wire up to

100 m (328 ft) in length.

3 Controller

4 AO terminal

5 COM terminal

Figure 10: Universal input voltage mode wiring

Callout Description

1 Field device

2 Power supply

3 Controller

4 UI terminal

FT-04A Quick Start Guide4

Callout Description

5 COM terminal

6 22 AWG copper stranded twisted wire up to

100 m (328 ft) in length

7 COM terminal

8 OUT terminal

Figure 11: Universal input resistance mode

Callout Description

1 22 AWG copper stranded twisted wire up to

100 m (328 ft) in length

2 Controller

3 UI terminal

4 COM terminal

Figure 12: Universal input digital dry contact input

Callout Description

1 Field device

2 22 AWG copper stranded twisted wire up to

100 m (328 ft) in length

3 Controller

4 UI terminal

5 COM terminal

Dry contact6

Normally open (NO) or normally closed (NC)

as required

Power supply terminal wiring

Connect the 24 VAC supply power wires from the

transformer to the HOT and COM power terminals as

shown in Figure 13.

Note: The supply power wire colors may differ on

transformers from other manufacturers. Refer to

the transformer manufacturer’s instructions and the

project installation drawings for wiring details.

Important: To reduce noise, interference, and

ground loop problems, connect a 24 VAC supply

power to the controller and to all other network

devices so that transformer phasing is uniform

across network devices. The controller does not

require an earth ground connection. However, when

you need to ground the secondary of the 24 VAC

transformer, make only one ground connection

near the transformer. For more information, see the

following figure.

Figure 13: Transformer grounding

CAUTION

To avoid property damage, check all wiring

connections before you apply power to the system.

If you wire this terminal incorrectly, a short circuit

can occur across the 24 VAC power supply on the

controller. A short circuit can cause a tripped circuit

breaker or a blown fuse. If you use a transformer

with a built-in fuse, you may need to replace the

transformer.

Controller interfacing

To interface with a controller and its inputs and outputs

with Controller Programming Tools (CPT) and the

controller's web server, establish a connection from your

device.

Note: Use the following procedures to set up

a controller on a primary network. For more

information about a secondary network setup, refer

to the product's User Reference Guide.

Connecting to a controller with Wi-Fi

1. On the desktop toolbar on your computer, click

your Wi-Fi network icon.

2. Find the controller's SSID, then connect to the

controller.

FT-04A Quick Start Guide 5

Note: Your controller's default SSID is a

combination of the controller's series letters

and the last four characters of the controller's

MAC address, for example, FT-012A. You can

find the MAC address on the label on the back

of the controller.

3. Enter the default password. For more information,

contact your supplier.

4. To ping the controller, at the command line, enter

ping, followed by the controller's IP address.

Note: For more information on your

controller's default IP address, see Primary

network default IP address, subnet mask, and

gateway.

Primary network default IP address,

subnet mask, and gateway

Table 1: Default IP address, subnet mask, and gateway

for a primary network setup

Item Address

IP address 192.168.4.1

Subnet mask 255.255.255.0

Gateway 192.168.10.1

Interfacing with a controller's web

server

About this task:

To interface with a controller's web server, complete the

following steps:

1. Launch a HTML5 web browser, such as Chrome™,

Firefox®, Microsoft Edge®, or Safari®.

2. In the web browser's address bar, enter your

controller's IP address, then press the Enter key or

Return key.

Interfacing with controller objects using

CPT

Use CPT to program EasyIO controller logic with the

Sedona framework.

1. To download the CPT application, contact Support

for the latest release.

2. Unzip the folder and double-click the cpt.exe file.

Note: If CPT is already installed on your

computer and you want to update it to a new

release, do not click and launch the cpt.exe

file to avoid personal settings data loss.

Instead, unzip the package and drop all the

files into the existing CPT folder to merge and

overwrite outdated files.

3. To connect to a controller, click File, then click

Open App.

4. In the Project Management window, on the

Recent tab, click New.

5. In the App Desc field, enter a name for the

controller.

6. In the Host field, enter the controller's IP address.

Note: The default IP address is 192.168.4.1

Note: For more information about your

controller's IP address, refer to the Controller

series IP address, subnet mask, and data

folder section of the EasyIO CPT User Guide

(LIT-12013978).

7. From the Data Folder list, select the folder for your

controller type.

Note: For FS Series controllers, select

SedonaFG.

Note: For more information about your

controller's data folder, refer to the Controller

series IP address, subnet mask, and data

folder section of the EasyIO CPT User Guide

(LIT-12013978).

8. Click Save.

9. Click Open.

10. In the Authentication dialog, enter your password

in the Password field.

Note: By default, there is no password.

To increase security, when you log on,

complete the steps in Creating a new CPT

admin password for a controller in EasyIO

Hardening Guide (LIT-12013986).

What to do next:

For more information on CPT, Refer to EasyIO CPT User

Guide (LIT-12013978).

FT LED states

Table 2: FT LED states

LED label LED color Normal state State Description

1 Hz blinks Normal operationSTS Blue 1 Hz blinks

Fast blink Controller in fault condition or controller in

bootloader mode

FT-04A Quick Start Guide6

Troubleshooting

Table 3: Troubleshooting

Problem Cause Solution

The transformer shorted.The controller does not

turn on due to one of the

following problems:

• The transformer

trips. Power is at the

transformer primary

and there is no voltage

at the secondary.

• The breaker or fuse

trips. Power is at

transformer primary.

You find 24 V at

secondary and 0 V at

breaker or fuse.

The 24 VAC powered sensor is not

wired with the same polarity as the

controller.

1. Ensure that the polarity of ~24 V COM on the

controller, auxiliary devices, and input and

output devices is the same.

2. Verify that the short circuit is resolved with an

ohm-meter.

3. Reset the breaker or fuse, or replace the

transformer.

Note: If you replace the transformer,

replace it with a model that uses a reset-

table circuit breaker. A circuit breaker

makes it easier to solve wiring problems.

4. To verify the connection, complete the following

steps:

a. Disconnect the secondary of the 24 VAC

transformer.

b. Use an ohm-meter to measure between ~24

V H and G at the controller. Ensure that no

short circuit occurs.

Note: If your installation requires that

you earth ground the transformer sec-

ondary, verify that the earth ground

connection is valid and not shared

between multiple pieces of equipment.

Analog output mode is

invalid. 0 V to 10 V output

is set to 100%, but output

terminals are less than 10 V.

Load impedance is lower than 2k

ohms.

1. Ensure that the voltage control device load

impedance is higher than 2k ohms. For

more information, refer to voltage device

manufacturer specification.

2. Disconnect the connected device and verify that

the value you require is present.

Analog mode for a

configurable output is

invalid. For example, 0 V to

10 V output results in an

unwanted offset of up to 1 V.

The Common Reference is

incorrect.

The COM terminal is not

connected.

1. Connect the COM terminal of the configurable

output to the common of the connected end

device.

2. Measure the output and verify that it matches

the command.

3. Disconnect the connected device and verify the

commanded value is present.

Technical specifications

Table 4: FT-04A UL input, output, and communication ratings

Specification Description Terminal

• 24 VAC, ± 5%

• 24 VDC, + 20% or - 15%

Power supply

2.5 VA, Class 2

H and G

Voltage 0 VDC to 10 VDC, Class 2Universal

inputs Resistance 3k to 50k Ohm

3% accuracy UI1, UI2 and

COM

Voltage 0 V to 10 V, Class 2

Minimum load impedance 2k ohm

Analog output

Maximum current draw 5 mA

3% accuracy AO1, AO2 and

COM

FT-04A Quick Start Guide 7

Table 5: FT-04A technical specifications

Specification Description

Controller processor and memory specifications

Main processor ESP32 240Mhz

Flash memory 16 MB

RAM 4 MB

Product temperature and humidity specifications

Operating temperature 0°C to 50°C (32°F to 122°F)

Storage temperature -20°C to 65 °C (-4°F to 150°F)

Operating humidity 10% RH to 90% RH, non condensing

Physical specifications

Dimensions 50 mm x 60 mm x 19 mm (2 in. x 2.4 in. x 0.7 in.)

Material UL approved

Weight 42 g (1.5 oz)

Wireless ratings

Standard IEEE 802.11

Band b/g/n

Frequency range 2412 MHz to 2472 MHz

Antenna Onboard antenna

Transmission power 16.6 dBm EIRP

FT-04A Quick Start Guide8

Compliance

Table 6: FT-04A Compliance

North America: UL 916 Energy Management Equipment;

FCC Class B, Part 15, Subpart C 15.247

FCC

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s). This device complies with part 15 of the FCC Rules.

Operation is subject to the follow-ing two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et

Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-lation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help. Limited by local law regulations, version for North America does

not have region selection option.

This radio transmitter IC: 2AKZUFT has been approved by Innovation, Science and Economic Development Canada to operate with

the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain

greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Gain of antenna: 2.2 dBi max

Type of antenna: Onboard antenna

Le présent émetteur radio IC: 2AKZUFT a été approuvé par Innovation, Sciences et Développement économique Canada pour

fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans

cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour

l'exploitation de l'émetteur.

Gain d'antenne: 2.2 dBi maximal

Type d'antenne: Antenne embarquée

To satisfy FCC & IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of

this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.

Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm.

Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la position centrale de l’ antenne.

CE Compliant

RED directive

The Equipment named above is confirmed to comply with the requirements set out in the European Council Directive on the

Approximation of the Laws of the Member States relating to 2014/53/EU (RED). The equipment passed the following test which was

performed according to the following European standards:

EN 301 489-1 V2.2.0 (2017-03, EN 301 489-17 V3.2.0(2017-03, EN 300 328 V2.1.1(2016-11, EN 62311(2008)

UKCA

Directive Electromagnetic Compatibility Regulations 2016:

BS EN 55032:2015+A11:2020, BS EN IEC 61000-3-2:2019/A1:2021, BS EN 61000-3-3:2013+A1:2019, BS EN 55035:2017+A11:2020

FT-04A Quick Start Guide 9

Product warranty

This product is covered by a limited warranty, details

of which can be found at www.johnsoncontrols.com/

buildingswarranty.

Patents

Patents: https://jcipat.com

Single point of contact

APAC EU UK NA/SA

JOHNSON

CONTROLS

C/O CONTROLS

PRODUCT

MANAGEMENT

NO. 32

CHANGJIANG

RD NEW

DISTRICT

WUXI JIANGSU

PROVINCE

214028

CHINA

JOHNSON

CONTROLS

VOLTAWEG 20

6101 XK ECHT

THE

NETHERLANDS

JOHNSON

CONTROLS

TYCO PARK

GRIMSHAW

LANE

MANCHESTER

M40 2WL

UNITED

KINGDOM

JOHNSON

CONTROLS

5757 N GREEN

BAY AVE.

GLENDALE, WI

53209

USA

Contact information

Contact your local Johnson Controls representative:

www.johnsoncontrols.com/locations

Contact Johnson Controls: www.johnsoncontrols.com/

contact-us

are subject to change without notice.

www.johnsoncontrols.com

Indice

Altri manuali Johnson Controls Sistema I/O

Johnson Controls

Johnson Controls IOM4710 Manuale utente

Johnson Controls

Johnson Controls MS-IOM1710-0 Manuale utente

Johnson Controls

Johnson Controls EasyIO FS Series Manuale utente

Johnson Controls

Johnson Controls IOM4711 Manuale utente

Johnson Controls

Johnson Controls IOM2721 Manuale utente

Johnson Controls

Johnson Controls IOM3711 Manuale utente

Johnson Controls

Johnson Controls Tyco Kantech KT-MOD-IO16 Manuale utente

Johnson Controls

Johnson Controls Metasys MS-IOM4711 Series Manuale utente

Johnson Controls

Johnson Controls FX-PCX47 Manuale utente

Johnson Controls

Johnson Controls IOM3733 Manuale utente

Johnson Controls

Johnson Controls IOM3721 Manuale utente

Johnson Controls

Johnson Controls IOM1711 Manuale utente

Johnson Controls

Johnson Controls M300MJ-4-20 Manuale utente

Johnson Controls

Johnson Controls FX-PCX47 Manuale utente

Johnson Controls

Johnson Controls IOM3733 Manuale utente

Johnson Controls

Johnson Controls IOM3731-0A Manuale utente

Johnson Controls

Johnson Controls FX-PCX17 Series Manuale utente

Johnson Controls

Johnson Controls FX-PCX2721 Manuale utente

Johnson Controls

Johnson Controls FX-PCX1711 Series Manuale utente

Johnson Controls

Johnson Controls IOM2723 Manuale utente

Johnson Controls

Johnson Controls MIOA Series Manuale utente

Johnson Controls

Johnson Controls IOM3721 Manuale utente

Johnson Controls

Johnson Controls FX-PCX37 Manuale utente

Johnson Controls

Johnson Controls FX-PCX3731 Manuale utente

Manuali Sistema I/O popolari di altre marche

WAGO

WAGO 750-344 Manuale utente

Teknim

Teknim TWM-1887 Manuale di istruzioni

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuale utente

BERGHOF

BERGHOF ECC DIO 16/16 Manuale di istruzioni

Advantech

Advantech PCM-27J3AU Manuale di installazione e funzionamento

Festo

Festo CP-E08-M12-CL Manuale utente

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuale utente

Hitachi

Hitachi HX-RIO3 Series Manuale utente

NUUO

NUUO SCB-A08 Manuale utente

M-system

M-system R3Y-RS8 Manuale utente

jablotron

jablotron JB-110N Manuale utente

Omron

Omron SYSMAC C200H Manuale utente

DOLD

DOLD SAFEMASTER M Manuale utente

ABB

ABB OPT-MF-001 Manuale utente

Omron

Omron SYSMAC C2000H Manuale utente

Helmholz

Helmholz TB20 Manuale utente

ICP DAS USA

ICP DAS USA tM-AD2 Manuale utente

Automationdirect.com

Automationdirect.com DL305 Manuale utente