Jonsa DF/TXDG12 Manuale utente

AUSTRALIA

PRODUCT CODE: DF/TXDG12

47 MHz ... 2400 MHz

DIRECT FIBRE TV TRANSMITTER 1550 nm INSTRUCTION MANUAL

2 3

DIRECT FIBRE TV TRANSMITTER 1550 nm [47 MHz ... 2400 MHz]

SAFETY PRECAUTIONS

WARNING: Avoid personal injury and product damage by complying with the following important

operating and maintenance instructions.

Avoid Electric Shock

WARNING: To reduce the risk of an electric shock, perform only the instructions that are included in

this instruction manual. Refer all servicing to a qualiﬁed service technician.

Do not apply power to the TX until all components have been installed and all of the wiring has

been properly terminated. Failure to do so may result in damage to the product and this will void the

manufacturer’s warranty.

Do not attempt to terminate, change or un-install any of the wiring without ﬁrst switching off the unit

and unplugging the AC power cord from the TX. Be sure to switch off the power at the outlet and the

TX prior to disconnecting or unplugging the power cords from the unit.

The voltage supplied must be at the recommended VAC, otherwise the TX could suffer irreparable

damage and subsequent invalidation of the warranty.

Note:

•Do not connect the TX to the power if the power cord is damaged

•Do not cut the AC power cords

Servicing

WARNING: Avoid electric shock! Opening or removing the cover may expose you to dangerous

voltages. Do not open the cover of this product and attempt service unless instructed to do so in the

operating instructions. Refer all servicing to qualiﬁed personnel only.

Laser Safety

CAUTION

VISIBLE AND INVISIBLE LASER RADIATION

AVOID EXPOSURE TO THE BEAM

Grounding Terminal

WARNING: This product is equipped with an external grounding terminal, attach one end of a

2.5mm to the grounding terminal; then, attach the other end of the wire to an earth ground, such as

an equipment rack that is grounded or CET.

DIRECT FIBRE TV TRANSMITTER 1550 nm [47 MHz ... 2400 MHz]

CONTENTS

SAFETY PRECAUTIONS 2

CONTENTS 3

INTRODUCTION & SPECIFICATIONS 4

1.1 Product Overview 4

1.2 Features 4

1.3 Main Technical Speciﬁcation Parameters 4

APPEARANCE 5

1.4 Front View 5

1.5 Bottom View 5

TROUBLESHOOTING 6

1.6 Troubleshooting 6

DIAGRAMS 6

1.7 Fibre Transmitter Diagram 6

1.8 Device Installation Diagram 6

1.9 System Installation Diagram 6

WARRANTY 7

1.1 Product Overview

This is an all-in-one direct ﬁbre transmitter for the use in medium to large ﬁbre distribution networks. It can be

used as a standalone Fibre Direct Transmitter or combined with our EYDFA.

This device provides long life stability and reliability.

1.2 Features

•Fibre output wavelength: 1550 nm ±10

•RF input: 47 MHz to 2400 MHz

•Fibre simultaneous dual outputs at + 12 dBm and + 9 dBm

•Module design, simple installation

•Redundant power supply

•19" rack mounting in a 1RU space

•Low power consumption

1.3 Main Technical Speciﬁcation Parameters

4 5

DIRECT FIBRE TV TRANSMITTER 1550 nm [47 MHz ... 2400 MHz]

INTRODUCTION & SPECIFICATIONS

Specifications

DF/TXDG12

Optical Power (mW) 15.85 7.95

Optical Power (dBm) 12 9

Optical Wavelength (nm) 1550 ± 10

Fibre Connection SC/APC

RF Bandwidth (MHz) 47 ... 2400

Channels 70 [Mix of DVB-C, DVB-T and DVB-S/S2]

Band Unflatness ≤0.75

Optical Modulation Mode Direct

Optical Return Loss ≥50

RF Input Level (dBµV) 70 ± 2 @ AGC

Input Return Loss ≥10

Input Impedance (Ω)75

CNR (dB) ≥51

CTB (dB) ≥65

CSO (dB) ≥65

Power Consumption (W) ≤4

Dual Power Supply (V) 110 VAC ... 254 VAC or 48 VDC

Storage Temperature (°C) - 10 ... + 50

Operation Temperature (°C) 0 ... + 50

Humidity (%) 20 ... 85

Dimensions (mm) 483 x 370 x 44

Name Function

Power A LED ON: Working Normally | LED FLASHING: Abnormal or No Power

Power B LED ON: Working Normally | LED FLASHING: Abnormal or No Power

SYS-WAR LED ON: Working Normally | LED FLASHING: Laser Output Lower than Normal Value (SYS-WAR = SYSTEM WARNING)

Menu LCD Menu Toggle Button

DIRECT FIBRE TV TRANSMITTER 1550 nm [47 MHz ... 2400 MHz]

APPEARANCE

1.4 Front Panel

Key Number LCD (Display) Line Description

0DF/TXDG12 DF/TXDG12 is the Product Code / Model of the Fibre Optical Direct Transmitter

S/N: 20180818002 Indicates the Serial Number of the Device

1OP_A Pow: The output power of laser A.

Bias1: The laser A bias current.

2A+5V: PSU A +5V Status. If the voltage is < + 4.2 V, "LOW" is displayed, if above + 5.8 V, "High" is diplayed

A-5V: PSU A -5V Status. If the voltage is < - 5.8 V, "LOW" is displayed, if above 5.8 4 V, "High" is diplayed

3B+5V: PSU B +5V Status. If the voltage is < + 4.2 V, "LOW" is displayed, if above + 5.8 V, "High" is diplayed

B-5V: PSU B -5V Status. If the voltage is < - 5.8 V, "LOW" is displayed, if above 5.8 4 V, "High" is diplayed

4DF/TXDG12 DF/TXDG12 is the Product Code / Model of the Fibre Optical Direct Transmitter

Soft Ver:1.0.0.1 Software Version loaded in the Fibre Transmitter

Name Function

Grounding Terminal, Connect to Earth [CET]

Laser Out (+ 9 dBm) + 9 dBm Fibre Optic Signal Output SC/APC Connector

Laser Out (+ 12 dBm) + 12 dBm Fibre Optic Signal Output SC/APC Connector

RF Input RF Signal Input: 47 MHz to 2400 MHz, F Female Connector

Back Up Back up Power Supply Module

Main Main Power Supply Module

1.5 Rear Panel

1.7 Fibre Transmitter Diagram

PUMP

RF INPUT

70 ± 2 dBµV

OPT

LCD

& KEY

CPU

POWER A

MAIN

POWER B

BACK UP

+ 9 dBm OUTPUT

+ 12 dBm OUTPUT

1.9 System Installation Diagram

STB &/OR

RF DISTRIBUTION

NETWORK

INTERNET

SERVICE

EYDFA

ONE

PON

SATELLITE

FIBRE

RECEIVER

FIBRE

OPTIC

MODEM

SATELLITE

FIBRE

TRANSMITTER

MULTIPLE

PON'S

INPUT

1.8 Device Installation Diagram

CONNECT

GROUND WIRE

& POWER CORD

TURN

DEVICE

INSTALLING

THE FIBRE

TRANSMITTER

CONNECT

SIGNAL

CABLES

ACQUISITION

CHECK

+ 12 dBm

OUTPUT

+ 9 dBm

OUTPUT

POWER

SWITCH

6 7

DIRECT FIBRE TV TRANSMITTER 1550 nm [47 MHz ... 2400 MHz]

1.6 Troubleshooting

1. Q. The LED indicator for Power A or Power B is ﬂashing?

A. Check the power cord inputs and ensure the switch on the power outlet along with the device is

switched on.

2. Q. The LED indicator for SYS-WAR is off.

A. Check the laser output power using a Fibre Power Meter, this indicates a lower than nominal output.

TROUBLESHOOTING

DIAGRAMS

CAUTION: DO NOT FEED THE + 12 dBm FIBRE OPTICAL OUTPUT INTO THE EYDFA INPUT!

THIS MAY CAUSE DAMAGE TO THE EYDFA.

DIRECT FIBRE TV TRANSMITTER 1550 nm [47 MHz ... 2400 MHz]

Please keep a copy of your proof of purchase with this Instruction Manual / Warranty.

DO NOT SEND BACK TO JONSA AUSTRALIA

PLEASE READ THIS WARRANTY AND KEEP IT WITH YOUR PURCHASE RECEIPT

Please complete these details and retain your original proof of purchase as you will require both documents

to claim this as a warranty repair. Keep the documents in a safe place for future reference should you need to

return this product to your place of purchase, during the warranty period of up to 12 months from the date

of purchase.

Customer Details

Name First Name Serial Number

Surname

Address Name [St, Ave, Drv etc] State

Suburb Post Code

Dealer or Installer Details

Name First Name Serial Number

Surname

Address Name [St, Ave, Drv etc] State

Suburb Post Code

Please Note:

• Beforemakingaclaimonthisproduct,pleasecheckyourInstructionManual.Youwillhavetopay

attention to non-product problems and operator errors.

• Thiswarrantydoesnotcoverfaultsbytheownersmisuse,includingbutnotlimitedtodamagefromshock,

or from foreign substances such as dirt or liquid entering the product.

ATTACH YOUR PROOF OF PURCHASE HERE...

WARRANTY

Version V1.3

+61 1300 660 155 +61 1300 250 407 www.jonsa.com.au [email protected]u

WA branch

Unit 1,

7 Mallaig Way,

Canning Vale

WA 6155

Australia

saleswa@jonsa.com.au

PO Box 6147,

Silverwater

NSW 1811

Australia

Head Ofﬁce

Lidcombe Business Park,

Unit D2,

3 - 29 Birnie Avenue,

Lidcombe

NSW 2141

Australia

AUSTRALIA

Indice

Altri manuali Jonsa Trasmettitore

Jonsa

Jonsa DF/TXD9 Manuale utente

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente