JUKI PLC-2760NV Manuale utente

PLC-2760NV

INSTRUCTION MANUAL

CONTENTS

1. Specications ................................................................................................................. 1

2. Threading the machine head......................................................................................... 2

3. Pneumatic components (when the pneumatic center guide is used) ....................... 3

4. Setting the incidental device (pneumatic center guide) ............................................ 5

4-1. Setting the ON/OFF status of the center guide ................................................... 5

4-2. Setting the optional input for the the center guide............................................. 7

4-3. Setting the optional output for the center guide ................................................ 8

CAUTION

This Instruction Manual for the PLC-2760NV only describes their di󰀨erences from the stan-

dard models (PLC-2760V).

For safety-related information, carefully read and fully understand "Safety precautions"

described in the Instruction Manual for the standard models before using your sewing ma-

chine.

– 1 –

Item Application

Model PLC-2760NV

Sewing speed Max. 2,500 sti/min

Refer to "10. SEWING SPEED TABLE"

in the Instruction Manual for the standard model.

Stitch length Max. 12 mm

Needle SCHMETZ 134×35 (Nm 125 to Nm 200) (Standard : Nm 140)

Applicable thread size for sewing #30 to #0 (US: #46 to #266, Europe: 60/3 to 10/3)

Applicable thread size to be cut #30 to #0 (US: #46 to #266, Europe: 60/3 to 10/3)

Motor AC servo motor

Presser foot pressure control Electronic control

Horizontal feed control Electronic control

Alternate vertical feed control Electronic control

Lubricating oil JUKI New Defrix Oil No. 1 (equivalent to ISO standard VG7)

or JUKI MACHINE OIL No. 7

Number of patterns Sewing pattern ............................ 99 patterns (For the polygonal shape sewing,

as many as 10 patterns can be registered.)

Cycle sewing pattern ................... 9 patterns

Custom-pitch pattern ................... 20 patterns

Condensation custom pattern ..... 9 patterns

Noise -Equivalent continuous emission sound pressure level (LpA) at the

workstation:

A-weighted value of 83.5 dB; (Includes KpA = 2.5 dB); according to ISO

10821- C.6.2 - ISO 11204 GR2 at 2,500 sti/min.

-Sound power level (LWA);

A-weighted value of 90.5 dB; (Includes KWA = 2.5 dB); according to ISO

10821- C.6.2 - ISO 3744 GR2 at 2,500 sti/min.

1. Specications

PLC-2760NVSA70BBZ

– 2 –

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the

following work after turning the power o󰀨 and ascertaining that the motor is at rest.

Thread the machine head following the order as

illustrated in the gure.

If you want to perform thread trimming at a position where no material exists, it is necessary to

change thread guide 󱢶 with the suitable thread guide. The thread guide to be used instead of the

current one is supplied with the unit as an accessory.

Part number of replacement thread guide: 40034675

❻

❸

❼

❹

❶

󱢳

❾

󱢴

󱢶

❺

󱢵

❷

❶

❷

❼

❹

❻

❹

❺❺

❼

❻

❾

󱢷

󱢶

󱢷

❽

󱢸

Left-hand

needle thread Right-hand

needle thread

2. Threading the machine head

– 3 –

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the

following work after turning the power o󰀨 and ascertaining that the motor is at rest.

(1) Installing the regulator

1) Install regulator (asm.) ❶on mounting plate ❺

with screw ❷, spring washer ❸and nut ❹which

are supplied with the unit.

2) Attach joint ❻to inlet 1. Attach joint ❼to outlet

3) Attach mounting plate ❺on the undersurface of

the table with accessory screws ❽supplied with

the plate.

4) Connect the ø6 air tube to joint ❼.

* Screw ❷which is supplied with the unit:

Thread diameter M5; Length: 12 mm

(SM6051202TP)

(2) Adjusting the air pressure

1) The operating air pressure is 0.5 to 0.55 MPa.

Adjust the air pressure using air pressure regulat-

ing knob ❶ of the lter regulator.

2) In the case uid accumulation is observed in A

section of the lter regulator, turn drain cock ❷to

drain the uid.

Decrease Increase

❶

❷

❶

❺

❼

❻

❹

❸

❽

3. Pneumatic components (when the pneumatic center guide is used)

– 4 –

❸

❹

❶

❷

❺

2ø4 tube

(3) Attaching the solenoid valve

1) Attach solenoid valve asm. ❷to the under-

surface of the table with accessory screw ❶

(SK3452001SE).

2) Connect the ø6 tube described in step 4) in "(1)

Installing the regulator" to joint ❸.

Cut the ø6 tube to an appropriate length before

use.

3) Connect the ø4 air tube coming from the air type

center guide to joint ❹.

4) Connect connector ❺to the CN59 on the electri-

cal control box.

– 5 –

4. Setting the incidental device

4-1. Setting the ON/OFF status of the center guide

❶

1) ❶held pressed for three second.

The "mode screen" is displayed.

2) Select "14. Incidental device setting".

3) The "Incidental device setting screen" is dis-

played.

When the device setting of which is to be

changed is selected, the setting screen for the

selected device is displayed.

4) Select "1. Center guide" to display the "Center

guide setting screen".

5) Select "H001 Function ON/OFF" to display

the "Center guide function ON/OFF setting

screen".

– 6 –

❷

❹

❻

❸

❺

6) Select ON/OFF status of the function.

7) Press ❷to conrm the setting.

8) Press ❸ to display the sewing data

edit screen.

9) Press ❹ to display the "S056 center

guide".

10) Then, set the ON/OFF status of the center

guide.

11) Press ❺ to conrm the value you

have entered.

12) Press ❻ to display the sewing screen.

If the pneumatic center guide does not function just by setting its ON/OFF status, set the optional in-

put/output of the center guide as described in the next paragraph to enable the function of the pneu-

matic center guide.

– 7 –

❶

4-2. Setting the optional input for the the center guide

Assign the switching function of the center guide to the 6-gang switch.

1) ❶held pressed for three second.

The "mode screen" is displayed.

2) Select "19. Optional I/O setting".

3) Select "1. Optional input setting".

4) Select "INPUT6. Thread clamp switch input".

– 8 –

❶

5) Select "i62. Center guide input".

6) Press ❷ to conrm the selection.

4-3. Setting the optional output for the center guide

1) Select "2. Optional output setting".

2) Select "OUTPUT11. Function is not provided".

3) Select "o25. Center guide".

4) Press ❶ to conrm the selection.

❷

Indice

Manuali Macchina da cucire popolari di altre marche

Riccar

Riccar RL634DE Manuale utente

Singer

Singer 2517 Manuale utente

Pfaff

Pfaff 3307-1 SERIES Manuale utente

Janome

Janome Quilt Maker Pro 18 VERSA Manuale utente

Siruba

Siruba C007JP Manuale utente

Husqvarna Viking

Husqvarna Viking Designer SE Manuale utente

Singer

Singer 148-5 Manuale utente

IKEA

IKEA SY Manuale utente

Pfaff

Pfaff 571 Manuale utente

Singer

Singer 15-91 Manuale utente

Brother

Brother BB370 Manuale utente

Pegasus

Pegasus WT100 Series Manuale utente

Reliable

Reliable 7100DB Manuale utente

Pfaff

Pfaff 937 Manuale utente

Singer

Singer 6038 Manuale utente

Singer

Singer 413K Manuale utente

Pfaff

Pfaff 1471 E1 Manuale utente

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuale utente