Jung ZLLHS4-01 Manuale utente
ZigBee radio hand-held transmitter
Art. No. : ZLLHS4-01
Operating instructions
1 1 Safety instructions
Device components
(1) LED
The LED lights up green as long as the button is pressed.
When the functions "Individually set lights" or "Service functions" are active, the LED lights
up red.
During commissioning the LED indicates the functional state, see Chapter 4.
(2) Buttons for switching/dimming
(3) Scene buttons/functional buttons
ZigBee radio hand-held transmitter
1/15
82595215
J0082595215 28.06.2017
Intended use
- ZigBee Light Link transmitter for operation of ZigBee Light Link compatible participants,
e.g. lamps, luminaires, light bands, ballast units, adapters
- The transmitter can work with ZigBee Light Link devices or with systems of other manufac-
turers, e.g. Philips Hue or Osram Lightify.
- Use inside in dry rooms.
- Battery-powered device
iIn the operating manual, participants will henceforth be called luminaires.
Insert battery
iKeep contacts of batteries and device free of grease.
oObserve polarity: The positive pole of the battery must be on top.
oPlace battery on the positive contact of the battery holder and push lightly to lock in place.
2 2 Basic functions
2.1 Switching or dimming luminaires
iAll luminaires connected to the transmitter will be collectively switched or dimmed.
oSwitching: Short press on the Ɔ or ƍ button.
oDimming: Long press on the Ɔ or ƍ button. The dimming process ends when the
button is released.
2/15
ZigBee radio hand-held transmitter
82595215
J0082595215 28.06.2017
2.2 Recalling scene
Scenes help you to save individual settings of one or more persons and to recall them with a
single press of a button.
oBriefly press the corresponding scene button Ƈ to ƌ.
The luminaires that belong to that scene will switch to the stored values.
2.3 Saving scene
iIf the scene is to be recalled from several transmitters, it must be stored separately at each
transmitter.
oLuminaires that are not part of the scene must be switched off prior to saving.
oTo set the luminaires to the desired values, see chapter 3.
oPress the corresponding scene button Ƈ to ƌ longer than 4 seconds.
LED lights up green for 3 seconds. The scene is saved on the selected button.
3/15
ZigBee radio hand-held transmitter
82595215
J0082595215 28.06.2017
3 3 Setting luminaires individually
3.1 Selecting a luminaire
oBriefly press the Ɔ and ƍ buttons simultaneously.
LED lights up red.
All luminaires that are connected to the transmitter are selected. The luminaires acknowl-
edge this e.g. by short flashing.
iIf only a single luminaire is to be set, press the Ɔ and ƍ buttons simultaneously
until the respective luminaire is selected. When the last luminaire connected to the trans-
mitter has been selected, all luminaires connected to the transmitter will be selected the
next time the buttons Ɔ and ƍ are pressed.
oSwitch on the luminaire by briefly pressing the ƍ button.
oSet the luminaire. The available settings depend on the luminaire used.
Luminaire selection Ǝ Ɔ and ƍ
Switching and brightness Ǝ Ɔ or ƍ
light color Ə Ƈ or ƈ
Color saturation Ɛ Ɖ or Ɗ
Color temperature Ƒ Ƌ or ƌ
oWait for approx. 6 seconds until the transmitter switches back to the basic functions.
oAs an option, save the settings as a scene, see Chapter 2.3.
3.2 Switching or dimming luminaires individually
oSelecting a luminaire, see Chapter 3.1.
4/15
ZigBee radio hand-held transmitter
82595215
J0082595215 28.06.2017
oSwitching: Short press on the Ɔ or ƍ button.
oDimming: Long press on the Ɔ or ƍ button. The dimming process ends when the
button is released.
3.3 Setting the light color Ə
oSelecting a luminaire, see Chapter 3.1.
oSetting a predefined color: press the Ƈ or ƈ button briefly until the desired light color
is set.
oSetting an individual light color: press the Ƈ or ƈ button until the desired light color
is set.
Depending on the current light color, the color changes towards the next predefined color.
3.4 Setting the color saturation Ɛ
oSelecting a luminaire, see Chapter 3.1.
oSetting white: briefly press Ɖ.
oSetting the maximum color saturation: briefly press Ɗ.
oSetting individual color saturations: press the Ɖ or Ɗ button until the desired color
saturation is set.
5/15
ZigBee radio hand-held transmitter
82595215
J0082595215 28.06.2017
3.5 Setting the color temperature Ƒ
oSelecting a luminaire, see Chapter 3.1.
oSetting warm white: briefly press the Ƌ button.
The color temperature is set to approx. 2700 K, which is typical for light bulbs.
oSetting cold white: briefly press the ƌ button.
The color temperature is set to approx. 4500 K, which is typical for fluorescent lamps.
oSetting individual color temperatures: press the Ƌ or ƌ button until the desired color
temperature is set.
The color temperature increases or decreases to the respective final value that the lumi-
naire supports.
4 4 Commissioning
4.1 Basic commissioning procedure
Prerequisite 1:
During commissioning, the respective devices must have a distance of 10 to 50 cm to each oth-
er.
Prerequisite 2:
Each device can only be part of one network.
The luminaire should be operated using a Philips Hue Bridge or an Osram Lightify Gate-
way and transmitters
oUp-to-date information on this is always available on our website.
The luminaire should be operated exclusively using a transmitter without connection to a
Philips Hue Bridge or Osram Lightify Gateway.
The luminaire has default settings.
oConnect the luminaire to a transmitter, see Chapter 4.2
or the luminaire belongs to another network.
oReset luminaire, see Chapter 4.5.
oConnect the luminaire to a transmitter, see Chapter 4.2.
iRepeat the corresponding steps for another luminaire.
The lamp should be operated with several transmitters without a connection to a Philips
Hue Bridge or Osram Lightify Gateway.
Prerequisite:
The luminaire is already connected to a transmitter, see Chapter 4.2.
oAdd a new transmitter to the network, see Chapter 4.3.
6/15
ZigBee radio hand-held transmitter
82595215
J0082595215 28.06.2017
oConnect the luminaire to the new transmitter, see chapter 4.2.
4.2 Connecting a luminaire to a transmitter
oPress the Ɔ and ƌ buttons simultaneously until the LED flashes green.
The luminaire flashes briefly. Connection in process.
LED on the transmitter lights up green. Luminaire lights up green or flashes twice. Connec-
tion has been set up successfully.
LED on the transmitter flashes red quickly for 3 seconds. Could not set up connection.
iIn case of error, if the distance between the devices is too big or the luminaire already
belongs to an existing network, see Chapter 4.5.
Alternatively, all memory locations in the transmitter are occupied. In this case, delete all
connections to luminaires that are not needed, see Chapter 4.6.
4.3 Adding the transmitter to an existing network
iIf the transmitter already belongs to a network, reset it beforehand, see Chapter 4.7.
Prerequisite:
At least one luminaire must be switched on.
oPress Ƌ and ƍ buttons on the new transmitter simultaneously until the LED flashes
green.
The new transmitter is in programming mode.
oWithin 10 seconds, start a connection process on a transmitter from the existing network
(see Chapter 4.2 or the manual of the respective transmitter).
7/15
ZigBee radio hand-held transmitter
82595215
J0082595215 28.06.2017
iAfter 10 seconds, if no connection process is started, the transmitter will search for an
open network in order to join it.
LED lights up green for 3 seconds. Transmitter has been added to a network.
LED flashes red quickly for 10 seconds. Transmitter has not been added to a network.
4.4 Cloning the transmitter
All connections of a transmitter are transferred to another transmitter. This function can only be
used with our company's transmitters.
oTo add a new transmitter to the existing network, see Chapter 4.3.
Prerequisite:
At least one luminaire must be switched on.
oPress Ƌ and ƍ buttons on the new transmitter simultaneously until the LED flashes
green.
The new transmitter is in programming mode.
oWithin 10 seconds, start a connection process on the transmitter to be cloned, see
Chapter 4.2.
LED lights up green for 3 seconds. The new transmitter has accepted the connections.
LED flashes red quickly for 10 seconds. The new transmitter has not accepted any connec-
tions.
4.5 Resetting a luminaire
All connections of the luminaire will be disconnected and the assignment to a network deleted.
iIf several luminaires are mounted near each other, it might be necessary to switch off those
luminaires that are not to be reset.
8/15
ZigBee radio hand-held transmitter
82595215
J0082595215 28.06.2017
oKeep the Ƈ and ƈ buttons pressed until the LED flashes green.
The luminaire flashes. Resetting in process.
LED lights up green; luminaire lights up. Resetting successful.
LED flashes red quickly for 3 seconds. Participant could not be reset.
4.6 Deleting connections from the transmitter to the luminaires
iThe transmitter can store a maximum of 10 connections to luminaires. If the memory is full,
a connection needs to be deleted first in order to save a new connection.
oPress Ɔ and ƍ buttons simultaneously.
LED lights up red. All connections to luminaires are selected.
oPress the Ɔ and ƍ buttons briefly and simultaneously until the connection to be
deleted is selected.
The corresponding luminaire flashes.
iIf the corresponding luminaire is defective or no longer exists, press the Ɔ and ƍ
buttons simultaneously until no luminaire flashes after pressing. The transmitter indicates
this by a red-flashing LED.
oPress the Ƈ and ƈ buttons simultaneously for longer than 4 seconds.
LED lights up green for 3 seconds. The connection has been deleted from the transmitter.
9/15
ZigBee radio hand-held transmitter
82595215
J0082595215 28.06.2017
4.7 Resetting the transmitter to the default setting
iAll connections to luminaires will be disconnected and the assignment to a network delet-
ed.
oKeep the Ɖ and Ɗ buttons pressed.
After approx. 10 seconds, the LED flashes green.
oRelease the Ɖ and Ɗ buttons and press the Ɔ button within 10 seconds.
Transmitter is reset to the default settings. After completion, the LED lights up green for
3 seconds.
5 5 Service functions
5.1 Switching on the service functions
The service functions can only be used with our company's transmitters. They enable you, for
example, to connect fixed wall transmitters to luminaires when these cannot be brought into
connection range to each other or to pass on existing connections from one transmitter to
another.
Prerequisite:
To use the service functions (switched on), the transmitter must be part of the network, see
Chapter 4.3, and at least one luminaire must be switched on.
oHold the transmitter within a range of 10 to 50 cm from the luminaire or transmitter.
10/15
ZigBee radio hand-held transmitter
82595215
J0082595215 28.06.2017
Indice
Altri manuali Jung Trasmettitore
Jung
Jung FMHSD24 Manuale utente
Jung
Jung FMx5001M Series Manuale utente
Jung
Jung BLE 2990-L Series Manuale utente
Jung
Jung ZLLCD5004M Manuale utente
Jung
Jung eNet FM 4001 M Manuale utente
Jung
Jung 42 FH Manuale utente
Jung
Jung A 41 F Series Manuale utente
Jung
Jung FF 21 WW Manuale utente
Jung
Jung FM4002M Manuale utente
Jung
Jung FM 4001 M Manuale utente
Jung
Jung FMS 4 UP Manuale utente
Jung
Jung FUS22UP Manuale utente
Jung
Jung FM Series Manuale utente
Jung
Jung HS2 RF Manuale utente
Jung
Jung HS2 RF Manuale utente
Jung
Jung eNet FMHS2 Manuale utente
Jung
Jung KNX 4071RFTSM Manuale utente
Jung
Jung 41F Series Manuale utente
Jung
Jung FUS22UP Manuale utente
Jung
Jung EnOcean ENO A 590 Series Manuale utente
