Juniper SRX3600 Manuale utente

Replacing the Switch Fabric Board on the SRX3600 Services Gateway

The SFB is accessible from the front panel, in the topmost slot. It weighs

approximately 5.1 lb (2.3 kg). Before you replace the SFB, you must power off the

services gateway.

To replace an SFB:

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis. For more information

about ESD, see Preventing Electrostatic Discharge Damage to the SRX3600

Services Gateway.

2. If you have not already done so, power off the device by pressing the Power

button on the front panel of the Switch Fabric Board (SFB) for three to five

seconds.

The PWR LED blinks to show you that the device is shutting down. Wait for the

device to shut down before proceeding.

3. Place an electrostatic bag or antistatic mat on a flat, stable surface.

4. Disconnect any cables attached to the SFB front panel connectors.

5. Loosen the screws on either end of the SFB front panel.

6. Pull open the ejector handles and slide the SFB halfway out of the chassis.

7. Place one hand underneath the SFB to support it and slide it completely out of

the chassis.

8. Place the SFB on the antistatic mat.

Figure 1: Removing the SFB

g036061

Captive screwEjector levers

9. Carefully align the sides of the replacement SFB with the guides inside the chassis.

10. Slide the SFB into the chassis until you feel resistance.

11. Grasp both ejector handles and press toward the center of the card to fully seat

the SFB.

Replacing the Switch Fabric Board on the SRX3600 Services Gateway ■1

12. Tighten the screws on either side of the card.

13. Reconnect the cables, if any, that you disconnected from the SFB front panel

connectors in Step 4.

Figure 2: Inserting the SFB

g036060

Captive screwEjector levers

14. Power on the services gateway by pressing the Power button on the front panel

of the SFB for three to five seconds. Wait for the device to start.

15. Verify that the SFB is functioning normally by checking the LEDs on its faceplate.

The SFB STATUS LED should light steadily green a few minutes after the device

is powered on. If the SFB STATUS LED is red, remove and install the SFB again.

If the SFB STATUS LED still lights steadily red, the SFB is not functioning properly.

Contact your customer support representative.

To check the status of the SFB:

user@host> show chassis environment fpc 0

CB 0 status:

State Online Master

Temperature 30 degrees C / 86 degrees F

Power 1

1.2 V 1202 mV

1.5 V 1511 mV

1.8 V 1798 mV

2.5 V 2481 mV

3.3 V 3306 mV

5.0 V 4956 mV

12.0 V 12084 mV

1.25 V 1250 mV

3.3 V SM3 3287 mV

5.0 V RE 5046 mV

12.0 V RE 11910 mV

Power 2

11.3 V bias PEM 11292 mV

11.3 V bias FPD 11156 mV

11.3 V bias POE 0 11253 mV

11.3 V bias POE 1 11272 mV

Bus Revision 42

FPGA Revision 1

2■Replacing the Switch Fabric Board on the SRX3600 Services Gateway

Related Topics ■Required Tools and Parts for Replacing Hardware Components on the SRX3600

Services Gateway

■Replacing a Routing Engine on the SRX3600 Services Gateway

■Replacing a Network Processing Card on the SRX3600 Services Gateway

■Replacing a Services Processing Card on the SRX3600 Services Gateway

■Replacing an I/O Card on the SRX3600 Services Gateway

■Replacing an AC Power Supply on the SRX3600 Services Gateway

Published: 2010-04-20

Replacing the Switch Fabric Board on the SRX3600 Services Gateway ■3

Altri manuali per SRX3600

Indice

Altri manuali Juniper Portale

Juniper

Juniper SRX380 Manuale utente

Juniper

Juniper SRX345 Istruzioni per l'installazione

Juniper

Juniper SRX 5800 Manuale utente

Juniper

Juniper SRX3400 Istruzioni per l'installazione

Juniper

Juniper SRX100 Istruzioni per l'installazione

Juniper

Juniper SRX5600 Manuale di istruzioni

Juniper

Juniper SRX-4600 Istruzioni per l'installazione

Juniper

Juniper SRX5400 Manuale utente

Juniper

Juniper SRX Series Manuale utente

Juniper

Juniper SRX320 Manuale utente

Juniper

Juniper SRX345 Istruzioni per l'installazione

Juniper

Juniper SRX 5800 Manuale utente

Juniper

Juniper SRX100 Manuale utente

Juniper

Juniper SRX5600 Manuale utente

Juniper

Juniper SRX 5800 Manuale utente

Juniper

Juniper SRX5600 Manuale utente

Juniper

Juniper SSG140 Istruzioni operative e di sicurezza

Juniper

Juniper SSG320M Manuale utente

Juniper

Juniper SRX 210 Manuale utente

Juniper

Juniper SRX 210 Manuale utente

Juniper

Juniper SRX5600 Istruzioni per l'installazione

Juniper

Juniper SRX5600 Manuale utente

Juniper

Juniper SRX240B Manuale utente

Juniper

Juniper SRX 210 Istruzioni per l'installazione

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente