Juniper MX480 Manuale utente

MX480 3D Universal Edge Router

Quick Start

January 2015

Part Number: 530-040794

Revision 01

This document describes how to install the Juniper Networks®MX480 3D Universal Edge

Router.

Contents MX480QuickStartDescription.........................................3

Step 1: Prepare the Site for MX480 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Rack-MountingRequirements......................................4

Tools Required to Unpack and Prepare the MX480 Router for

Installation ..................................................5

Step 2: Install the Mounting Hardware in a Four-Post Rack or Cabinet or an

Open-FrameRack................................................6

Step3:InstalltheRouter..............................................9

RemoveComponents.............................................9

InstalltheRouterUsingaLift......................................10

Install the Router Without a Mechanical Lift . . . . . . . . . . . . . . . . . . . . . . . . . . 12

ReinstallComponents............................................13

Step4:ConnecttheGroundingCable...................................14

Step 5: Connect External Devices and Line Card Cables . . . . . . . . . . . . . . . . . . . . . 15

Connect to a Network for Out-of-Band Management . . . . . . . . . . . . . . . . . . . 15

ConnectaManagementConsole...................................15

ConnecttheLineCardCables......................................15

Step6:ConnectPowerCables.........................................17

Connect Power to an AC Router with Normal-Capacity Power Supplies . . . . 17

Connect Power to an AC Router with High-Capacity Power Supplies . . . . . . . 17

Connect Power to a DC Router with Normal-Capacity Power Supplies . . . . . 18

Connect Power to a DC Router with High-Capacity Power Supplies . . . . . . . 20

Step 7: Perform Initial Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

EnterConfigurationMode.........................................23

Configure User Accounts and Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

ConfigureSystemAttributes......................................24

CommittheConfiguration........................................24

SafetyWarnings....................................................26

ComplianceStatementsforNEBS.....................................27

Compliance Statements for EMC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Canada .......................................................28

EuropeanCommunity............................................28

Israel .........................................................28

Japan.........................................................28

United States ..................................................29

Junos Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

RequestingTechnicalSupport........................................30

Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

OpeningaCasewithJTAC.........................................31

RevisionHistory.....................................................31

MX480 3D Universal Edge Router Quick Start

MX480 Quick Start Description

This Quick Start contains information you need to install and configure the router quickly.

For complete installation instructions, see the MX480 3D Universal Edge Router Hardware

Guide at http://www.juniper.net/techpubs/.

WARNING: This Quick Start contains a summary of safety warnings in “Safety

Warnings” on page 26. For a complete list of warnings for this router, including

translations, see the MX480 3D Universal Edge Router Hardware Guide at

http://www.juniper.net/techpubs/.

The MX480 3D Universal Edge Router is 8 rack units (U) tall. Five routers can be stacked

in a single floor-to-ceiling rack, for increased port density per unit of floor space. The

router provides eight slots that can be populated with up to six Dense Port Concentrators

(DPCs) or Modular Port Concentrators (MPCs), three Flexible PIC Concentrators (FPCs),

and two SCBs. Each FPC holds up to two PICs and each MPC holds up to two Modular

Interface Cards (MICs).

Each Packet Forwarding Engine enables a throughput of 10 Gbps. Many types of DPCs

are available. For a list of the DPCs supported, see the MX Series 3D Universal Edge

Routers Line Card Guide.

The MX480 supports up to 3 FPCs containing up to 6 PICs or up to 6 MPCs containing

up to 12 MICs. For a list of the supported line cards, see the MX Series Interface Module

Reference.

The router is shipped in a cardboard box strapped securely to a wooden pallet. Plastic

straps secure the top and bottom in place. The router chassis is bolted to this pallet.

Quick Start installation instructions and a cardboard accessory box are also included in

the shipping container.

MX480 Quick Start Description

Step 1: Prepare the Site for MX480 Installation

•Rack-Mounting Requirements on page 4

•Tools Required to Unpack and Prepare the MX480 Router for Installation on page 5

Rack-Mounting Requirements

•You can install the router in a four-post rack or cabinet or an open-frame rack.

•The rack rails must be spaced widely enough to accommodate the router chassis's

external dimensions: 14.0 in. (35.6 cm) high, 24.5 in. (62.2 cm) deep, and

17.45 in. (44.3 cm) wide. The outer edges of the mounting brackets extend the width

to 19 in. (48.3 cm).

•The rack must be strong enough to support the weight of the fully configured router,

up to 163.5 lb (74.2 kg). If you stack five fully configured routers in one rack, it must be

capable of supporting about 818 lb (371.0 kg).

•For service personnel to remove and install hardware components, there must be

adequate space at the front and back of the router. Allow at least 30 in. (76.2 cm) in

front of the router and 24 in. (61 cm) behind the router.

•The rack or cabinet must have an adequate supply of cooling air.

•Ensure that the cabinet allows the chassis hot exhaust air to exit from the cabinet

without recirculating into the router.

•The router must be installed into a rack that is secured to the building structure.

•Mount the router at the bottom of the rack if it is the only unit in the rack.

•When mounting the router in a partially filled rack, load the rack from the bottom to

the top with the heaviest component at the bottom of the rack.

MX480 3D Universal Edge Router Quick Start

Figure 1: MX480 Rack Clearance and Router Dimensions

Tools Required to Unpack and Prepare the MX480 Router for Installation

To unpack the router and prepare for installation, you need the following tools:

•A mechanical lift—recommended

•Phillips (+) screwdrivers, numbers 1 and 2

•2.5-mm flat-blade (–) screwdriver

•7/16-in. (11 mm) torque-controlled driver or socket wrench

•1/2-in. or 13-mm open-end or socket wrench to remove bracket bolts from the shipping

pallet

•Electrostatic discharge wrist strap

•Antistatic mat

Tools Required to Unpack and Prepare the MX480 Router for Installation

Step 2: Install the Mounting Hardware in a Four-Post Rack or Cabinet or an Open-Frame

Rack

To install the mounting shelf on the front rails of a four-post rack or cabinet, or the rails

of an open-frame rack:

1. If needed, install cage nuts in the holes specified in Table 1 on page 6.

2. On the back of each rack rail, partially insert a mounting screw into the lowest hole

specified in Table 1 on page 6.

3. Install the mounting shelf on the back of the rack rails. Rest the bottom slot of each

flange on a mounting screw.

4. Partially insert screws into the open holes in each flange of the mounting shelf (see

Figure 2 on page 7 or Figure 3 on page 8).

5. Tighten all the screws completely.

Table 1: MX480 Mounting Hole Locations

Mounting ShelfDistance Above U DivisionHole

X1.14 U2.00 in. (5.1 cm)4

X0.86 U1.51 in. (3.8 cm)3

X0.50 U0.88 in. (2.2 cm)2

X0.14 U0.25 in. (0.6 cm)1

MX480 3D Universal Edge Router Quick Start

Figure 2: MX480 Mounting Hardware for a Four-Post Rack or Cabinet

g004258

Four-post open rack

Small mounting shelf

Step 2: Install the Mounting Hardware in a Four-Post Rack or Cabinet or an Open-Frame Rack

Figure 3: Mounting Hardware for an Open-Frame Rack

MX480 3D Universal Edge Router Quick Start

Step 3: Install the Router

Because of the router's size and weight, you must remove all components before installing

the router. We also recommend that you install the router using a mechanical lift.

•Remove Components on page 9

•Install the Router Using a Lift on page 10

•Install the Router Without a Mechanical Lift on page 12

•Reinstall Components on page 13

Remove Components

Figure 4: Components to Remove from the Front of the MX480 Router

Figure 5: Components to Remove from the Rear of the MX480 Router

Before lifting the router, you must remove the following components:

•Power supplies

•Switch Control Boards (SCBs)

Step 3: Install the Router

•Routing Engines

•Air filter

•Fan tray

•Line cards:

•Dense Port Concentrators (DPCs)

•Flexible PIC Concentrators (FPCs)

•Physical Interface Cards (PICs)

•Modular Port Concentrators (MPCs)

•Modular Interface Cards (MICs)

To remove the components from the router:

1. Slide each component out of the chassis evenly so that it does not become stuck or

damaged.

2. Label each component as you remove it so you can reinstall it in the correct location.

3. Immediately store each removed component in an electrostatic bag.

4. Do not stack removed components. Lay each one on a flat surface.

NOTE: For complete instructions on removing router components, see

“Installing the MX480 Chassis in the Rack Manually” in the MX480 Router

Hardware Guide.

Install the Router Using a Lift

To install the router using a lift:

1. Ensure that the rack is in its permanent location and is secured to the building. Ensure

that the installation site allows adequate clearance for both airflow and maintenance.

For details, see the MX480 3D Universal Edge Router Hardware Guide.

2. Load the router onto the lift, making sure it rests securely on the lift platform (see

Figure 6 on page 11).

MX480 3D Universal Edge Router Quick Start

Altri manuali per MX480

Indice

Altri manuali Juniper Router di rete

Juniper

Juniper T Series Manuale utente

Juniper

Juniper ACX5448 Manuale utente

Juniper

Juniper MX150 Manuale utente

Juniper

Juniper J2300 Manuale utente

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV... Manuale utente

Juniper

Juniper 6rd Manuale utente

Juniper

Juniper AP45 Manuale

Juniper

Juniper T4000 - Manuale utente

Juniper

Juniper Day One+ ACX7024 Manuale utente

Juniper

Juniper MX104 Istruzioni per l'installazione

Juniper

Juniper MX204 Istruzioni per l'installazione

Juniper

Juniper ACX500 Istruzioni per l'installazione

Juniper

Juniper ACX Series Manuale utente

Juniper

Juniper PTX10002-60C Manuale utente

Juniper

Juniper J2300 Manuale utente

Juniper

Juniper ERX-1410 Manuale utente

Juniper

Juniper MX240 Manuale utente

Juniper

Juniper JRR200 Istruzioni per l'installazione

Juniper

Juniper MX204 Manuale utente

Juniper

Juniper T1600 Manuale utente

Juniper

Juniper PTX3000 Scheda tecnica

Juniper

Juniper M10i Istruzioni per l'installazione

Juniper

Juniper MX2020 Manuale utente

Juniper

Juniper V10000 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza