Juniper EX8216 Manuale utente
Mounting an EX8216 Switch on a Rack or Cabinet
The EX8216 switch ships installed with front-mounting brackets on the chassis for
mounting the switch on a 19-in. equipment rack or cabinet. (The remainder of this
topic uses “rack”to mean “rack or cabinet.”) The switch also comes with adjustable
mounting brackets to support it in the rack.
In a four-post rack, the switch consumes 21 U without the optional power cord tray
and 22 U with the optional power cord tray. Installation in a two-post rack is not
supported. You can mount two switches on a 42 U four-post rack provided that the
rack meets the strength requirements to support the combined weight of the switches.
WARNING: Because of the switch's size and weight, we require the use of a
mechanical lift to install the switch.
CAUTION: If you are installing more than one switch in a rack, install the first switch
at the bottom of the rack.
CAUTION: Do not install line cards in the chassis until after you mount the chassis
securely on a rack.
Before mounting an EX8216 switch on a rack:
1. Verify the site meets the requirements for installation described in Site
Preparation Checklist for an EX8200 Switch.
2. Place the rack in its permanent location, allowing adequate clearance for airflow
and maintenance, and secure it to the building structure. See Clearance
Requirements for Airflow and Hardware Maintenance for an EX8216 Switch for
detailed information.
3. Unpack the switch as described in Unpacking an EX8200 Switch.
4. Install the adjustable mounting brackets at the desired position in a four-post
rack (see Installing Adjustable Mounting Brackets in a Rack or Cabinet for an
EX8200 Switch).
5. Optionally, install the power cord tray, so you can use it to manage the power
supply cords (see Installing the Power Cord Tray in a Rack or Cabinet for an
EX8200 Switch).
6. Read General Safety Guidelines and Warnings for EX Series Switches, with
particular attention to Chassis Lifting Guidelines for EX8200 Switches.
Ensure that you have the following parts and tools available to mount the switch on
a rack:
■A mechanical lift
Mounting an EX8216 Switch on a Rack or Cabinet ■1
■A Phillips (+) screwdriver, number 2 or number 3, depending on the size of
your rack mounting screws
■20 mounting screws appropriate for your rack
To mount the EX8216 switch on a rack (see Figure 2):
1. Install the adjustable mounting brackets at the desired position in a four-post
rack (see Installing Adjustable Mounting Brackets in a Rack or Cabinet for an
EX8200 Switch). If you are planning to install the optional power cord tray, leave
at least 1 U of space below the adjustable mounting brackets (see Installing the
Power Cord Tray in a Rack or Cabinet for an EX8200 Switch). The power cord
tray is optional.
2. Load the switch onto the mechanical lift, making sure it rests securely on the lift
platform. See Figure 1.
Figure 1: Installing the Switch Chassis Using a Mechanical Lift
3. Using the lift, position the switch in front of the rack or cabinet, centering it in
front of the adjustable mounting brackets installed in the rack.
2■Mounting an EX8216 Switch on a Rack or Cabinet
4. Lift the chassis approximately 0.75 in. (1.9 cm) above the surface of the adjustable
mounting brackets. Position the chassis in the rack as close as possible to resting
on the support that the mounting brackets provide.
5. Carefully slide the switch onto the adjustable mounting brackets until the
front-mounting brackets (“ears”) attached to the chassis contact the rack rails,
using the handles on the lower side of the chassis to help guide it into position.
The adjustable mounting brackets installed in the rack ensure that the holes in
the front-mounting brackets align with the holes in the rack rails.
6. Move the lift away from the rack.
7. Ensure the chassis is flush with the front of the rack.
8. Install a mounting screw into each of the open front-mounting holes aligned with
the rack, starting from the bottom.
9. Visually inspect the alignment of the switch. If the switch is installed properly in
the rack, all the mounting screws on one side of the rack are aligned with the
mounting screws on the opposite side and the switch is level.
10. After ensuring that the switch is aligned properly, tighten the screws.
11. Insert 20 mounting screws appropriate for your rack (not provided) into the
aligned holes. Use the appropriate Phillips (+) screwdriver to tighten the screws
to the rack rail.
CAUTION: To meet safety and electromagnetic interference (EMI) requirements and
to ensure proper operation, you must connect EX8200 switches to earth ground
before you connect them to power. For installations that require a separate grounding
conductor to the chassis, use one of the two protective earthing terminals on the
switch chassis to connect to the earth ground. For instructions on connecting an
EX8200 switch to ground using a separate grounding conductor, see Connecting
Earth Ground to an EX Series Switch.
Mounting an EX8216 Switch on a Rack or Cabinet ■3
Figure 2: Installing an EX8216 Switch in a Four-Post Rack
Related Topics ■Removing an EX8216 Switch from a Rack or Cabinet
■Connecting AC Power to an EX8200 Switch
■Connecting DC Power to an EX8200 Switch
■Rack Requirements for an EX8216 Switch
■Cabinet Requirements and Specifications for an EX8216 Switch
Published: 2009-07-15
4■Mounting an EX8216 Switch on a Rack or Cabinet
Altri manuali per EX8216
2
Indice
Altri manuali Juniper Interruttore
Juniper
Juniper EX3300 Istruzioni per l'installazione
Juniper
Juniper 200 Series Manuale utente
Juniper
Juniper EX9253 Manuale utente
Juniper
Juniper EX2200 Series Istruzioni per l'installazione
Juniper
Juniper EX4600 Istruzioni per l'installazione
Juniper
Juniper EX3200 Series Istruzioni per l'installazione
Juniper
Juniper EX4200 Series Istruzioni operative e di sicurezza
Juniper
Juniper NFX350 Istruzioni per l'installazione
Juniper
Juniper EX Series Manuale di istruzioni
Juniper
Juniper EX 3200 Manuale utente
Juniper
Juniper EX3200 Series Guida rapida
Juniper
Juniper EX4300 Manuale utente
Juniper
Juniper EX8200 Series Manuale di istruzioni
Juniper
Juniper QFX5220-32CD Manuale utente
Juniper
Juniper EX8208 Manuale utente
Juniper
Juniper EX2300 Series Istruzioni per l'installazione
Juniper
Juniper NETWORK AND SECURITY MANAGER NSM3000 - REV... Manuale utente
Juniper
Juniper EX2500 Manuale utente
Juniper
Juniper EX8216 Istruzioni per l'installazione
Juniper
Juniper EX2200 Series Manuale utente
