Juuko HS-K800 series Manuale utente
2
Contents
CONTENTS
CONTENTS
Guarantee, service, repairs and maintenance
Chapter1: Customer infomation
General Information on Safety
Chapter2: General description
General description
END USER INSTRUCTIONS
Chapter 3: Receiver
INSTRUCTION GUIDE
Chapter 4: Failure Analysis and solution
2
2
3
3
4
4
5
6
7
8
7
Chapter 3: Receiver
Guarantee, service, repairs and maintenance
The JUUKO products are covered by a guarantee/warranty against material,
construction and manufacturing faults. During the guarantee/warranty period, JUUKO
may replace the product or faulty parts. Work under guarantee/warranty must be
carried out by JUUKO or by an authorized service centre specied by JUUKO.
This is not covered by the guarantee/ warranty:
▪Faults resulting from normal wear and tear
▪Parts of a consumable nature
▪Products that have been subject to unauthorized modications
▪Faults resulting from incorrect installation and use
▪Damp and water damage
Maintenance:
▪Repairs and maintenance must be carried out by qualied personnel
▪Use spare parts from JUUKO only
▪Contact your representative if you require service or other assistance
▪Keep the product in a dry, clean place
▪Keep contacts and antennas clean
▪Wipe o dust using a slightly damp,clean cloth
Optional external antenna
Mounting Dimensions
Wiring diagram
M8 screw recommend
46,5mm
156.0mm
165,5mm
Ø8.0mm
183.5mm
202,8mm
189.5mm
1
2
3
4
5
6
7
8
9
10
11
12
13
GROUND
POWER1
POWER2
COM
EMERG.-STOP
COM
UP
COM
DOWN
NA
NA
NA
NA
2A
POWER
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
COM
EAST
WEST
NA
COM
SOUTH
NORTH
NA
COM
1
2
NA
NA
NA
NA
COM
HORN
5A
Relay Y1
Relay Y2
Relay Y5
Relay Y6
Relay Y8
Relay Y9
Relay Y11
Relay Y12
Relay Y15
Y16 Y17
Button X1
Button X2
Button X3
Button X4
Button X5
Button X6
Button X7
Button X8
Button X17
8
Chapter 4: Failure Analysis and solution
HS-K800 series
Radio remote control system
BASIC INSTALLATION INSTRUCTIONS
(English)
Standard settings
-
Stain on the battery
springs.
-
Low battery.
-
Transmitter is not
communicated with
receiver.
-
Push button damaged.
-Clean the stains on battery
springs
.
-
Replace brand new
batteries.
-
Check the power supply
of receiver.
-
Check receiver’s fuse.
-
Contact the dealers.
LED Signal Failure Analysis Solution
LED red
LED green
LED red
LED green
SHORT
LONG
LED red
LED green
Troubleshooting
Transmitter
Receiver
Should an error occur, LED of the receiver unit will indicate the cause of the error.
-RF error
-
Receiver is not powered.
-Check the antenna and
make sure it is not loose.
-Contact dealer
-
Change the fuse.
-Check the power supply.
LED Signal Failure Analysis Solution
LED red
LED green
SHORT
LONG
LED red
LED green
LED red
LED green
Valid data or Invalid data (from a dierent transmitter)
received.
5
Chapter 2: General description
START/ Horn switch
The K series transmitter has an Start/Horn switch on the button-left
side. The Start/Horn switch has 2 modes:
1. Press to start
2. Press for horn while operating
Start the transmitter in operating mode
1. Turn to release the emergency button.
2. Press” START” button.
Turning the transmitter o
Turn the transmitter o by completely pressing the STOP-
button.
The transmitter turns o. All relays deactivate.
Change the batteries
Program the transmitters
BATTERY TYPE: 2 x 1.5V(LR6 AA)
1. Remove the battery cover
2.Remove both batteries.
The programming connector is placed
behind the battery
4
Chapter 2:General description
The K series teansmitter comes in dierent visions, featuring 2, 4, 6, or 8 pushbuttons.
The transmitter also features 2-step pushbuttons. Both steps of each pushbutton can operate
dierent functions like controlling the speed of a movement, step 1: slow, step 2: fast.
EMO
OFF
Operating pushbuttons
Status LED
ON/HORN
Loop for belt.
Dimensions
Frequency range
Typical response time for Stop command and commands
Typical operating range
Modulation method
Control system
Antenna impedance
Power supply
Antenna
Average power consumption
Radio-frequency power
Weight (including battery)
Housing materia
Protection degree
193×57×51mm(2-8 buttons)
433.0525~434.7775MHz
50mS~100mS
100M
4GFSK
PLL
50Ω
LR6(AA)1.5V x2
Internal
16mA@DC3V (default setting)
<10dBm (default setting)
approx.325g (2-8 buttons)
PA6(30% GF)
IP65
Operating and storage temperature (-20°C)~(+55°C) / (-40°C)~(+65°C)
Technical data
TRANSMITTER
LED 2
LED 1
Low battery
Error
X1
X9
X2
X10
X3
X11
X4
X12
X5
X13
X6
X14
X7
X15
X8
X16
X17
X1
X9
1st step
2nd step
6
Chapter 3: Receiver
3
Chapter 1: CUSTOMER INFORMATION
Thank you for purchasing a JUUKO product.
READ ALL INSTRUCTIONS CAREFULLY BEFORE MOUNTING, INSTALLING AND CONFIGURATING
THE PRODUCT.
This manual includes general information concerning the operation of the radio remote control
transmitter K series .
General Information on Safety
•Persons under the inuence of drugs and/or alcohol and/or other medicine that impairs their
reaction may not assemble, disassemble, install, put into operation, repair or operate the product.
•All conversions and modications of an installation/system must conform to the relevant safety
requirements. Work on the electrical equipment must be performed only by qualied, authorized
personnel and in accordance with the relevant safety requirements.
•In the event of malfunctioning and visible defects or irregularities, the product must be stopped,
switched o and the relevant master switches must be switched o.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionne-
ment.
FCC Part 15
* This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation
* You are cautioned that changes or modications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
Warning against hazardous situation
Warning against electrical voltage
Used Symbols and Denitions for Warnings
Receiver
WARNING! The receiver must NOT be opened by any other than a qualied installer.
Make sure to turn the electricity o before opening the receiver.
RF module
FUSE 2A
Function Relay SYNC.
Instruction guide
FUSE 5A
Dimensions
Frequency
Typical response time for Stop
command and commands
Sensitivity
Modulation method
Control system
Antenna impedance
Power supply
Antenna
Standby power
Weight
Housing materia
Protection degree
190×184×64 (mm)
433.0525~434.7775MHz
50mS~100mS
4GFSK
PLL
50Ω
24~264V AC/DC
Internal
16mA@AC220V
1795g
PA6(30% GF)
IP65
Operating and storage temperature
(-20°C)~(+55°C)/(-40°C)~(+65°C)
Technical data
Programming port
Power input
Keep distance
Area must be free
of obstructions
Indice
Altri manuali Juuko Telecomando
