Kögel Kolossos Manuale utente
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
INSTALLING KOLOSSOS FOR SRAM eTap AXS
KOLOSSOS: INSTALLATION MANUAL
WHAT’S IN THE BOX
Kolossos for SRAM eTap AXS Cage and Pulleys
Kogel eTap AXS tool
Loctite
Kogel stickers
Manual link card
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
INSTALLING KOLOSSOS FOR SRAM eTap AXS
KOLOSSOS: INSTALLATION MANUAL
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
TOOLS NEEDED FOR THIS INSTALLATION:
• Torx T10
• 2mm allen
• 5mm allen
• Felt tip pen
• Phillips screwdriver
• Chain tool
• Light grease
• New chain, since the Kolossos cage requires
a few extra links compared to the stock setup
STEP 1:
Shift the derailleur to the lowest gear or the largest
cog position. With the bike secure in the stand, remove
the chain.
STEP 2:
Remove the rear wheel.
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
INSTALLING KOLOSSOS FOR SRAM eTap AXS
KOLOSSOS: INSTALLATION MANUAL
STEP 4:
Remove the pulleys.
STEP 5:
Remove the back cage.
STEP 3:
Remove the derailleur.
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
INSTALLING KOLOSSOS FOR SRAM eTap AXS
KOLOSSOS: INSTALLATION MANUAL
STEP 7:
Use Kogel eTap AXS tool to remove
the front cage. Loosen the bolt 1 1/4 turn.
STEP 8:
After loosening the bolt, unwind the
spring tension, then remove the bolt
completely.
STEP 6:
Remove the rotation stop pin from the
front cage.
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
INSTALLING KOLOSSOS FOR SRAM eTap AXS
KOLOSSOS: INSTALLATION MANUAL
STEP 10:
Disassemble the Kolossos overized cage. Start with the
stop pin.
STEP 11:
Then release all bolts on the backside
and dissasemble.
STEP 9:
Keep the mounting bolt and spring aside to be reused.
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
INSTALLING KOLOSSOS FOR SRAM eTap AXS
KOLOSSOS: INSTALLATION MANUAL
STEP 13:
Once secure all the way set aside the cage. With a felt
tip mark identify the flat edge. Place a mark on the
rounded face identifing the edge that’s flat.
STEP 14:
Reinstall the spring in the derailleur body.
STEP 12:
Use the front cage to reset the position of the clutch
system in the derailleur body. Line up the D-shape on
the pulley cage with the D-shape inside the derailleur
body.
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
INSTALLING KOLOSSOS FOR SRAM eTap AXS
KOLOSSOS: INSTALLATION MANUAL
STEP 16:
Install the nut and tighten it a few revolutions, less
than finger tight.
STEP 17:
Load the spring tension by pivoting the front cage
clockwise around the center nut one revolution.
STEP 15:
Install the front cage. Align the spring with the the
center hole to set the recommended tension.
Use the forward hole (near the rotation stop pin) for
higher spring tension and security on rough terrain. Use
the backward hole for lowest possible friction: useful
for a time trial on smooth surface.
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
INSTALLING KOLOSSOS FOR SRAM eTap AXS
KOLOSSOS: INSTALLATION MANUAL
STEP 19:
Install the rotation stop screw.
STEP 20:
Install pulley wheels. “U” indicates upper pulley. “L”
indicates lower pulley. Make sure “U” and “L” are facing
outward when mounted on the frame.
STEP 18:
Align and engage the D-shape, then tighten the nut
to 6Nm. Check if the cage and clutch move freely for
operation.
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
INSTALLING KOLOSSOS FOR SRAM eTap AXS
KOLOSSOS: INSTALLATION MANUAL
STEP 22:
Install the derailleur back on the bike.
STEP 23:
Install rear wheel.
STEP 21:
Install back cage. Use Loctite and install
all bolts with Loctite. Torque setting,
less than 1Nm
KOGEL.CC USA: +1 915 777 5666 info@kogel.cc
INSTALLING KOLOSSOS FOR SRAM eTap AXS
KOLOSSOS: INSTALLATION MANUAL
STEP 25:
Adjust the derailleur position, upper and lower limit and
b-tension as per Sram’s instructions.
STEP 26:
Adjusting the B-tension: the gap between the largest
cog and the upper pulley should be the same as Sram’s
recommendation for the standard cage. The Sram
supplied gauge will not fit the oversized 14 tooth pulley.
Below are the recommended gaps between the top of
the pulley and largest cog for each cassette size:
26T: 15mm
28T: 10mm
33T: 6mm
36T: 6mm
STEP 24:
Install the new chain over the small ring, smallest cog.
Chain length is correct if there is a minimal tension on
the cage.
Altri manuali Kögel Accessori per biciclette
