König Electronic SEC-IPCAM100B Manuale utente

SEC-IPCAM100B(W)

SEC-IPCAM105B(W)

MANUAL (p. 2)

IP camera

2013-07-30

Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per König SEC-

IPCAM105B o cerca il tuo prodotto tra le migliori offerte di Videosorveglianza

ENGLISH

IP camera

FULL MANUAL

Table of contents:

• Introduction (p. 2)

• Safety precautions (p. 2)

• Packaging

content (p. 2)

• System

requirements (p. 2)

• Technical specifications (p. 2)

• Product

description (p. 3)

• User

instructions(p. 5)

• Warranty (p. 22)

• Disclaimer (p. 22)

• Disposal (p. 22)

Introduction:

Watch over your property with this genuine Plug & Play IP camera without the need for any IP setting or router

configuration. Easy and simple installation in just a few minutes, the free uCare Cam App allows you to watch

on your Smartphone, anytime and anywhere. Advanced features provide you with an email or App notification

when motion is detected. Photo and/or video footage can be play backed at any time you require.

• We recommend that you read this manual before installing/using this product.

• Keep this manual in a safe place for future reference.

Safety precautions:

This product should ONLY be opened by an authorised technician when service is required. Disconnect the

product from the mains and other equipment if a problem should occur. Do not expose the product to water or

moisture.

Packaging content:

1x IP camera

1x Camera mount

1x AC/DC adapter

1x Quick start guide

1x CD with complete manual

System requirements:

• Device running on iOS 5.0 or above

• Device running on Android 4.0 or above

• WiFi Router

Technical specifications:

Specifications: SEC-IPCAM100B/W SEC-IPCAM105B/W

Video codec: MJPEG

Resolution: VGA 640x480 / QVGA 320x240 / QQVGA 160x120

Frame rate: 1~25fps

Image sensor: CMOS

Lens: 3.6mm 3.0mm

Night vision: 1 Lux, 10 meter 1 Lux, 5 meter

Flash memory: 8 MB

Card storage: up to 32 GB SDHC (not included)

Audio: 2-way

(integrated microphone + loudspeaker)

1-way

(integrated microphone)

Networking Protocol: IPV4, ARP, TCP, UDP, ICMP, DHCP Client, NTP Client, DNS Client, SMTP

Client, P2P Transmission

Built-in network interfaces: 802.11b/g/n WLAN

Specifications: SEC-IPCAM100B/W SEC-IPCAM105B/W

Wireless security: Wireless security: WEP/WPA/WPA2 wireless encryption

Wireless transmit output

power:

Wireless transmit output power: 16.5 dBm for 11b, 13.5 dBm for 11g,

13.5 dBm for 11n (+/- 1.5dBm)

Video features: Adjustable image size and quality, Time stamp and text overlay, Flip

View Angle: H:39.3°, V:26.8°, D:46.5° H:46.4°, V:31.9°, D:54.5°

Digital zoom: Up to 4x

3A Control: AGC (Auto Gain Control), AWB (Auto White Balance),

AES (Auto Electronic Shutter)

Power: External AC-to-DC switching power adapter, 100 to 240 V AC, 50/60 Hz, Dc

Plug Output: 5 V DC/1 A

Dimensions (W x D x H): 88mm*46mm*116mm (excluded

camera mount)

74mm*74mm*65mm (excluded

camera mount)

Weight: 119 g (without mount) 72 g (without mount)

Max. power consumption: 2.3W 1.9W

Operating Temperature: 0 to 40 °C (32 to 104 ˚F)

Storage Temperature: -20 to 70 °C (-4 to 158 ˚F)

Humidity: Humidity: 20% to 80% RH non-condensing

Product description:

SEC-IPCAM100B/W

Front

LED indicator for status

of IP camera

WPS/Reset button for

set-up and reset

Microphone

No function

IR LED for 10 metre

night view

Light intensity sensor

for IR LED

Wifi antenna

Slot for Micro SD card

Back

5V DC input

Loudspeaker For

2-way Audio

communication

Connection for

camera mount

SEC-IPCAM105B/W

Front

LED indicator for status

of IP camera

Microphone

IR LED for 5 metre

night view

Light intensity sensor

for IR LED

Back

WPS/Reset button for

set-up and reset 5V DC input

Slot for Micro SD card

User instructions:

A. Hardware Installation

1. Please find a location to install the uCare Cam that is within good WiFi signal reach of your home router.

2. If you plan to hang the uCare Cam, you can use the mounting kit included.

3. If the power cable included is not long enough to reach a power outlet, please purchase an extender

cable from your local electronics store.

4. Connect the camera power adapter.

Warning:

Please use the power adapter included with your camera to avoid damage to the camera.

When the camera powers up, the status LED will be green for about 15 seconds before flashing red. If

there is no red LED flashing, please unplug the power cord, wait 5 seconds, then re-connect the power. It

will take about 60 seconds for the uCare Cam to finish starting up. The status LED should alternate

between red and green. If the status LED does not flash red and green, please press and hold the

WPS/REST button at the back of the uCare Cam for 10 seconds.

B. Hardware Installation

1. Download the Smartphone App “uCare Cam” from the App store (iOS) or Play

Store (Android).

2. Search for the App named “uCare Cam”, then download and install it on your

smartphone.

3. After the software installation is complete, this icon will appear . Click on

this to run the App.

C. uCare Cam APP Overview

Default camera password: 0000

Default manager name: admin

Default manager password: 0000

There are 4 major function tabs at the bottom of the App main screen.

Camera List Tab

This is the main App screen. In this tab, all of the cameras which have been added

will be listed.

WiFi Setting or WiFi Connect Tab

Please go to this tab to configure the uCare Cam WiFi settings.

There are two methods to install a new uCare Cam and connect it to a WiFi

Router.

1. Router Mode

2. WPS (WiFi Protect Setup) Mode

(Requires a Router with WPS function using WPA/WPA2 encryption -

WEP encryption will not work)

Play List Tab

Go to this tab to view all pictures taken by the user via smartphone. The pictures will be listed by camera.

Settings Tab

Configure uCare Cam settings and remote microSD Card video playback.

User will need to input a management ID and password to enter this tab.

Default management ID: admin Default password: 0000

If you forget your password, you can reset the uCare Cam by pressing the WPS/REST button on the back of

the camera for 10 seconds. This will restore the uCare Cam to factory settings. You will need to set up the

WiFi connection again after you reset the camera.

D. iOS – Setup uCare Cam WiFi

Method 1: Use WPS (WiFi Protected Setup)

Available if your WiFi router supports WPS and it is set to use WPA or WPA2 security encryption. WEP

security encryption is not supported in WPS mode. An easy way to check if your router supports WPS is to

look for a button that says “WPS” on the router. It may also be called “AOSS” or “QSS”.

1. Press and hold the WPS/REST button for 10 seconds at the back of the camera. It will reset and restart

the uCare Cam. After about 60 seconds, the LED colour should flash green and red.

2. Press “WPS” button on the WiFi router

3. Press the WPS/REST button on the back of the uCare Cam for 2 seconds.

•If the uCare Cam has entered the WPS connection mode, the status LED colour will turn a fast

blinking green.

4. The uCare Cam will try for up to 2 minutes to connect to the WiFi router using WPS.

5. If the LED colour changes to orange, your uCare Cam has successfully connected to your router. If the

LED does not change to orange, the setup has failed. Please make sure the uCare Cam is within WiFi

distance of your router, press the WPS/REST button for 10 seconds to reset the uCare Cam, and try the

setup again.

6. Use the smartphone App to add the uCare Cam into the Camera List. See instruction manual – “iOS - Add

uCare Cam (already connected to router) to App”.

Method 2: Use Router Mode

You will first need to connect to the router that is available inside the uCare Cam, configure the WiFi settings

for your home router, then the uCare Cam will restart and connect to your home router.

Write down, or have handy, the SSID of your WiFi router and your WiFi password. For example, the

SSID may be something like “TP-Link-XXXXX” or “NETGEAR”. You will need both the SSID and the

password during this process.

1. Make sure the status LED on the uCare Cam is blinking red and

green. If the status LED is not blinking red and green, please

press and hold the WPS/REST button for 10 seconds to reset the

uCare Cam. Wait for 1-2 minutes for it to restart and the LED

should turn red and green.

2. Connect your iOS device to the router inside the uCare Cam. To

connect to the uCare Cam router, open up “Settings” , then

“Wi-Fi” and let it search for a network. The network will be

“wifi-cam-p2p”. Click on “wifi-cam-p2p” to connect.

3. Now, open the smartphone App “uCare Cam” and click on

the tab at the bottom of the screen that says “WiFi Connect”.

Click on “Router mode”, then “Next”. You will see live video.

4. Enter the WiFi router SSID and password for your home router.

Click on the “Next” button and again, on the next screen, the

“Next” button.

5. Please enter a Camera name (2 to 20 characters) and the default

password “0000”. You are encouraged to change the default

password after setup for security purposes. Then click “Finish”.

6. After the uCare Cam receives this information, it will restart.

Please wait for it to start up and connect to your home router.

When it successfully connects, the status LED colour will turn

orange. It may take up to 10 minutes. If the status LED colour

does not turn orange, please check your router and make sure the

uCare Cam is within the signal area of your WiFi router. Then try

setup again, starting from Step 2.

7. Your iOS device should have disconnected from “wifi-cam-p2p” and reconnected to your home router.

Please check that your iOS device has connected to your home router now, via “Settings” -> “Wi-Fi”. If

it has not, please connect your smartphone to your home router WiFi.

8. Open the “uCare Cam” smartphone App, and you can click on the camera name in the Camera List view

to connect.

E. Android – Setup uCare Cam WiFi

There are two methods to set up the uCare Cam to connect to a new WiFi Router.

Method 1: Use WPS (WiFi Protected Setup)

Available if your WiFi router supports WPS and it is set to use WPA or WPA2 security encryption. WEP

security encryption is not supported for WPS mode. An easy way to check if your router supports WPS is to

look for a button that says “WPS” on the router. It may also be called “AOSS” or “QSS”.

1. Press and hold the WPS/REST button for 10 seconds at the back of the camera. It will reset and restart

the uCare Cam. After about 60 seconds, the LED colour should flash green and red.

2. Press “WPS” button on WiFi router

3. Press the WPS/REST button on the back of the uCare Cam for 2 seconds.

•If the uCare Cam has entered the WPS connection mode, the status LED colour will turn a fast

blinking green.

4. The uCare Cam will try for up to 2 minutes to connect to the WiFi Router using WPS.

5. If the LED colour changes to orange, your uCare Cam has successfully connected to your router. If the

LED does not change to orange, the setup has failed. Please make sure the uCare Cam is within WiFi

distance of your Router, press the WPS/REST button for 10 seconds to reset the uCare Cam, and try the

setup again.

6. Use the smartphone App to add the uCare Cam into Camera list. See instruction manual – “Android - Add

uCare Cam (already connected to router) to App”.

Method 2: Use Router Mode

Please have your WiFi password readily available as you will need it in this process.

1. Open the Smartphone APP “uCare Cam” and click on

the tab at the bottom of the screen that says “WiFi Setting”.

2. Click on “Router mode”.

3. Make sure the status LED on the uCare Cam is blinking red and

green. If the status LED is not blinking red and green, please

press and hold the WPS/REST button for 10 seconds to reset

the uCare Cam. Wait for 1-2 minutes for it to restart and the LED

should turn red and green.

4. Click “Next”. Your smartphone will start to search for the uCare

Cam. Once it finds it, you will see live video. Click on “Next”

button.

5. Your smartphone will search for nearby WiFi signals. Once they

are found, you will see a list of routers.

6. Click on your router name and enter your WiFi password in the

pop-up screen.

7. Please enter a Camera name (2 to 20 characters) and the

default password “0000”. You are encouraged to change the

default password after setup for security purposes. Then click

“OK” in the top right corner.

8. The camera will restart and the Smartphone App will

automatically connect to the camera in Live View.

9. When the uCare Cam successfully connects to your router, the

status LED colour will turn orange. It may take up to 10 minutes.

If the status LED colour does not turn orange, please check your

router and make sure the uCare Cam is within the signal area of

your WiFi Router. Then try the setup again.

10. If the setup is successful, the uCare Cam will be automatically

added to your Camera List window and you can click on the

camera name to view Live Video.

F. iOS – Add the uCare Cam (already connected to Router) to App

There are three ways to add a uCare Cam to the Camera List view if the uCare Cam is already connected to

the internet. You can:

•Scan for the uCare Cam in local intranet

•Scan QR code at the back of the uCare Cam

•Type in 20 digit code

Method 1: Scan for the uCare Cam in local intranet

1. Make sure your smartphone is connected to the same router

as your uCare Cam. Open up the Smartphone App “uCare

Cam” and click on the “+” at the top right of the

screen.

2. Click on “Scan Camera’s UID in intranet”.

3. You will see a list of UIDs that were found on your local

intranet.

4. Click on the UID you would like to add.

5. Please enter a Camera name (2 to 20 characters) and the camera password. The default password is

0000. Click “Done” on the top right of window.

6. You will see the Camera name now in Camera List view. It should indicate that the Camera is “Online”.

To connect to the Camera, please click on the Camera name. If the Camera is not “Online”, you may

need to force reconnect. To force reconnect, click on the right arrow and click on “Reconnect”. Click on

the Camera name once it shows “Online”.

Method 2: Scan QR Code at back of the uCare Cam

1. Make sure your smartphone is connected to the internet. Open up the Smartphone App “uCare Cam”

and click on the “+” at the top right of the screen.

2. Click on “Scan camera QR code”.

3. You will see your smartphone camera live view. Face your smartphone camera towards the QR code

found on the back of the uCare Cam. Please make sure the QR code is clear and fully viewable in the

screen. Once the QR code has been detected, the App will display the UID in the App window.

4. Please enter a Camera name (2 to 20 characters) and the camera password. The default password is

0000. Click “Done” on the upper right of the screen.

5. You will see the Camera name now in Camera List view. It should indicate that the Camera is “Online”.

To connect to the Camera, please click on the Camera name. If the Camera is not “Online”, you may

need to force reconnect. To force reconnect, click on the right arrow and click on “Reconnect”. Click on

the Camera name once it shows “Online”.

Method 3: Type in the 20 digit QR code

1. Make sure your smartphone is connected to the internet. Open up the Smartphone App “uCare Cam”

and click on the “+” at the top right of the screen.

2. Click in the “UID” field to enter typing mode.

3. Type in the 20 digit code exactly as printed underneath the QR code on the back of the uCare Cam.

4. Please enter a Camera name (2 to 20 characters) and the camera password. The default password is

0000. Click “Done” on the upper right of the screen.

5. You will see the Camera name now in the Camera List view. It should indicate that the Camera is

“Online”. To connect to the Camera, please click on Camera name. If the Camera is not “Online”, you

may need to force reconnect. To force reconnect, click on the right arrow and click on “Reconnect”. Click

on the Camera name once it shows “Online”.

G. Android – Add uCare Cam (already connected to router) to App

There are three ways to add a uCare Cam to the Camera List view if the uCare Cam is already connected to

the internet. You can:

•Scan for uCare Cam in local intranet

•Scan the QR code at back of uCare Cam

•Type in 20 digit code

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali König Electronic Telecamera IP

König Electronic

König Electronic VID-TRANS545KN Manuale utente

Manuali Telecamera IP popolari di altre marche

FLIR

FLIR Exx series Manuale utente

Avigilon

Avigilon H4A-BO1-IR Manuale utente

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuale utente

ShareTech

ShareTech AV1 Manuale utente

Ezviz

Ezviz C6C Manuale utente

Melchioni

Melchioni UCAM 2015 Manuale utente

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuale utente

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuale utente

Mitel

Mitel 6800i Series Manuale di servizio

Vitek

Vitek VTC-IR403-212NP Manuale utente

THOMSON

THOMSON DSC - 323W Manuale utente

AVer

AVer FB2027 Manuale utente

ENFORCER

ENFORCER EV-T5105-N2SQ Manuale utente

Wansview

Wansview NC543 Manuale utente

Eneo

Eneo MCB-64A0003M0A Manuale utente

deView electronics

deView electronics CBDNI36F Manuale utente

Swann

Swann SwannEye Manuale utente

LevelOne

LevelOne IP CamSecure Manuale utente