KegLand Fermzilla All-Rounder Starter Kit Manuale utente
Fermzilla All-Rounder Starter Kit Instruction Manual
Page 1of 4www.KegLand.com.au Last Updated 19/03/2020 6:20 PM
Starter Kit Instruction Manual
(for 30L and 60L all-rounder model)
This instruction sheet contains vital information that is related to the safe usage and
handling of the FermZilla All-Rounder. It is vital that you read this instruction sheet from
front to back before using the product! THIS IS FOR YOUR OWN SAFETY
Pressure rated and easy to clean, the capable all-rounder.
Starter Kit Instruction Manual
Page 2of 4www.KegLand.com.au Last Updated 19/03/2020 6:20 PM
WARNINGS
1. Do not add any liquid which is above 50°C (122°F) to the FermZilla. Only clean, wash
or sanitise the fermenter with cold water.
2. Under no circumstances apply more than 2.5bar (35PSI) to the fermenter tank and
do not connect an unregulated pressure source.
3. If you connect an external pressure source ensure it has an independent PRV pre-set
to 45 PSI or below
4. Do not tamper with the pressure relief valve. Only use the red coloured PRV’s
supplied by KegLand.
5. If the fermenter is scratched, damaged or has been under any physical duress; do
not use the fermenter under pressure.
6. Keep the fermenter out of direct sun or heat. Do not expose to UV rays of any sort.
7. If you are using a heat belt to warm the fermenter then only have the heat belt
sitting below the liquid level. Do not use an unregulated heat source, only use heat
sources which are plugged into a temperature controller set below 45°C.
8. If you use the fermenter under pressure hydro test the fermenter every 24 months
to ensure it is safe to use.
9. Do not use Sodium Metabisulphite or Stellarsoda in the FermZilla. Only use chemical
cleaners and sanitizers that are approved by Kegland. These include:
a) Super Kill Ethyl Sanitiser Spray (effective for santising the exterior of the FermZilla)
(KL05371)
b) StellarSan (mixed to the correct specification) (KL05357)
c) StellarClean (not to be left in the FermZilla for more than 24 hours) (KL05494)
… Or contact www.kegland.com.au for more information regarding other compatible
chemical cleaning products.
10. Do not over tighten the stainless handles onto the neck of the FermZilla. Over
tightening can warp the neck and potentially damage the unit. Make sure that the
handles can freely rotate around the neck of the FermZilla.
Fermzilla All-Rounder Starter Kit Instruction Manual
Page 3of 4www.KegLand.com.au Last Updated 19/03/2020 6:20 PM
11. Do not over tighten carbonation caps onto the threads of the lid or collection
container, doing so could result in the thread being stripped. We recommend using
the plastic carbonation and line cleaning cap (KL10788).
12. Avoid lifting the FermZilla while full.
What’s in the box
•1 x Fermzilla – 30L all-rounder fermenter
•1 x Fermzilla lid (KL11402)
•1 x Fermzilla lid ring (KL11396)
•2 x PET bottle caps
•1 x 3 Piece Airlock (KL01595)
Step-by-step instructions
1. Assembling the fermenter.
Once you have unboxed your KegLand 30L Flat-Bottom starter kit and checked everything is
included, begin by assembling your fermenter.
FermZilla – Lid Assembly
1. Ensure the lid assembly has the o-ring
attached.
2. Apply some food grade lubricant to the o-ring
to extend the life of this o-ring and threads.
3. Place the lid onto the neck of the tank and
screw down the threaded lid ring.
4. Use the two bottle caps to close the two
threaded holes in the lid.
5. Push the three piece air-lock into the remaining (central) hole of the lid
2. Cleaning and sanitizing the fermenter and equipment
1. Rinse the walls of the FermZilla vessel with cold water. A garden hose is particularly
useful for rinsing and dislodging yeast/hop matter.
Fermzilla All-Rounder Starter Kit Instruction Manual
Page 4of 4www.KegLand.com.au Last Updated 19/03/2020 6:20 PM
2. Fill the FermZilla with cold water and add Stellarclean according to the instructions
on the tub. Any other dirty brewing equipment can also be soaked in the fermenter.
3. Stellarclean can be left in the vessel for up to 24 hours
4. After a few hours of soaking, gently wipe away any soiling with a soft cloth. Make
sure not to use harsh scrubbers that may scratch the plastic and create ideal places
for batch-ruining bacteria to hide.
5. Once the fermenter is clean, rinse the PBW out with warm water.
6. Fill the FermZilla and collection vessel with cold water again and add Stellarsan
according to the instructions on the tub. Attach the lid and shake the full FermZilla to
coat all surfaces.
7. Stellarsan can be left in the vessel until the next fermentation when it can be
emptied and your wort added.
Suggested Additional Equipment
Looking to improve your kit and have the right gear on hand to do the job in the best
possible way?
•Ethanol spray (part # KL05371)
•Stellarsan (part # KL05357)
•Powerful Brewery Wash (‘PBW’) 1kg (part # KL05494)
•Heavy Duty Brewing Gloves (part # KL05289)
•Digital Temperature Controller (part # KL01946)
•Heating Wrap (part # KL01960) or Heating Belt (part # KL01953)
•FermZilla Pressure Kit (KB02113 or KB01609)
•Duotight – Blowtie 2 Spunding Valve (KL15042)
•Base Support/Webbing/Strap (KL13567)
•60cm Thermowell (KL14649)
Indice
Altri manuali KegLand Sistema di fermentazione
KegLand
KegLand KL25959 Manuale di istruzioni
KegLand
KegLand Fermzilla Manuale utente
KegLand
KegLand Fermzilla Unitank Series Manuale utente
KegLand
KegLand KL20671 Manuale utente
KegLand
KegLand Fermzilla Manuale utente
KegLand
KegLand KL14649 Manuale utente
KegLand
KegLand KL10955 Manuale utente
KegLand
KegLand Cannular Manuale di istruzioni
KegLand
KegLand KL25164 Manuale utente
KegLand
KegLand Fermzilla Manuale utente
Manuali Sistema di fermentazione popolari di altre marche
Animo
Animo ComBi CB5 Manuale utente
MoreBeer
MoreBeer BrewSculpture Manuale utente
Keurig Hot
Keurig Hot Commercial Series Manuale utente
Keg King
Keg King KEGMASTER XL Manuale utente
Blichmann Engineering
Blichmann Engineering BrewEasy Compact TC Istruzioni per l'installazione
Blichmann Engineering
Blichmann Engineering 3.5 BBL Hybrid Brewhouse Istruzioni per l'installazione