Kellermann Jetstream Manuale utente

Installation Manual

Jetstream

/Jetstream

Dear customer,

Thank you for placing your trust in us by

purchasing this product. Please read these

instructions carefully and completely before

deciding whether you would like to do the

installation yourself or have it done by a

specialist.

Legal Note: Jetstream®/Jetstream® DF

All Jetstream® are permitted by the ECE regulation

for motorcycles licensed for road use by EU law

as documented on the certification number em-

bossed on each lens. This means that you may

use two Jetstream® units instead of the original

indicator lights without any additional entries in

your motorcycle documents or presentation to a

motorcycle inspection organization in Germany,

or equivalent in other EU member states. You

do not need to carry any special documenta-

tion. This applies to all motorcycles licensed

under EU law and the corresponding lights.

ATTENTION! The warranty will not apply if

the Jetstream® has not been correctly installed

or connected to the electrical supply on your

motorcycle. Do not carry out the installation un-

less you are qualied to do so; otherwise, leave

the installation and connection work for your

Jetstream® to a qualied repair shop. The war-

ranty does not apply to damage due to wrong

connection or excess voltage (such as due to a

defective alternator regulator).

ATTENTION! Improper mechanical installation

or orientation of your Jetstream® lights may in-

validate your motorcycle’s roadworthiness and

insurance protection, or even lead to accidents.

Before every usage of your motorcycle, check

whether the indicators are correctly mounted

and fully functional.

WARNINGS

page 1

ATTENTION! Your Jetstream® lights may heat

up during use. Contact with bare skin or heat-

sensitive objects may lead to damage or injury.

ATTENTION! Each Jetstream® is tted with a

vibration-absorbing, elastic fastening arm (silent

rubber adapter). This wearing part is designed to

protect your Jetstream® from damage at slight

deections of up to 15°. The adaptor will break on

larger deections, such as from a crash or vanda-

lism, to prevent breakage to your valuable indi-

cator; the rubber will overstretch and tear, or the

inside will sustain so much damage that it may fail

at a later time.

ATTENTION! There are motorcycles with vol-

tage peaks, that damage Kellermann products.

These are: Older single cylinder KTM, Husaberg

and Husqvarna, Yamaha Raptor Quad and vehicles

of Skyteam, MZ and Simson and generally older

vehicles. Also other motorcycles with non factory

electrical system and e.g. retrotted ignition/ light-

ing systems e.g. from Vape/Powerdynamo and

others. The problem can be solved easily by instal-

ling suppressor diodes. Please contact our support

team ([email protected]) if you are un-

sure whether your motorcycle belongs to this

group. We point out that the warranty is void if

operating with over-voltage.

CLEANING ADVICE! Your new Kellermann pro-

ducts are premium-quality products. In order to

enjoy them long time and maintain the war-

ranty we recommend not to use any cleansers

with alkaline/acid and/or grinding substances

or steel wool. We also advice not to use steam

cleaners.

WARNINGS INSTALLATION

page 2

ATTENTION! Make sure that your motorcycle

is standing firmly before you start work, as a fall

may lead to damage to the motorcycle or injury

to you or others.

Dismantle the original indicators. Mount the

Jetstream® in place of the original indicators, or

drill a max. 8.5 mm diameter hole and fasten the

Jetstream® at 8 Nm with the self-locking M8 nut

supplied. Make sure that the surface under your

Jetstream® where the wires will emerge is pro-

tected from splash water. Mount the Jetstream®

in such a way that the beams run horizontally in

your motorcycle’s direction of travel.

Alignment is important to safety in trac and es-

sential to your motorcycle’s roadworthiness, as a

motorcycle with incorrectly aligned lights is easy

to overlook on the road.

Make sure that you keep the following measures

in selecting your fastening point:

Jetstream® | front | A= 194 mm

Jetstream® | front | B= 17 mm

Jetstream® | rear | C= 134 mm

WARNINGS INSTALLATION

deutsch

front

rear

Edge of

the illuminating

surface of the

headlamp

mounting

surface

mounting

surface

Refer to the ECE-R 48/ECE-R 53 guideline

available at https://unece.org/ for further

mounting regulations.

page 3

ATTENTION! Make sure that your motorcycle

is standing rmly before you start work, as a fall

may lead to damage to the motorcycle or injury

to you or others.

Dismantle the original indicators, rear and brake

light. Mount the Jetstream® DF in place of the ori-

ginal indicators, or drill a max. 8.5 mm diameter

hole and fasten the Jetstream® DF at 8 Nm with

the self-locking M8 nut supplied. Make sure that

the surface under your Jetstream® DF where the

wires will emerge is protected from splash water.

Mount the Jetstream® DF in such a way that the

beams run horizontally in your motorcycle’s di-

rection of travel.

Alignment is important to safety in trac and es-

sential to your motorcycle’s roadworthiness, as a

motorcycle with incorrectly aligned lights is easy

to overlook on the road.

Make sure that you keep the following measures

in selecting your fastening point:

Jetstream® DF | rear | C= 116 mm

rear

mounting

surface

INSTALLATION ELECTRICAL CONNECTION

Refer to the ECE-R 48/ECE-R 53 guideline avai-

lable at https://unece.org/ for further mounting

regulations.

page 3

Jetstream® DF | rear | C= 116 mm

Cut the wires between the original indicators

and the wire connectors at a suitable point. By

doing this the wiring loom stays untouched.

Connect your Jetstream® as follows:

To connect the wires of the indicator to the

wires of the original connector there are crimp

connectors and shrink tubings included in the

delivery. First push one of the shrink-on tubes

over one of the cables you want to connect and

remove ve millimeter of insulation on the end

of each cable. Then push both bare ends into a

crimp connector and crimp it with an appropriate

tool. Then pull the shrink-on tube over the con-

nection and heat it up equally until it ts tight

over the complete length of the connector.

This type of connection is technically permanent.

To create a non-permanent connection, we re-

commend Posilock wire connectors (not inclu-

ded), which are available for purchase from our

website at www.kellermann-online.com.

Lay the cables in a way, that they are protected

from splash water and fasten them, e.g. by using

zip ties. Now test the function of the Jetstream®.

This completes the installation.

•

Connect the positive of the left (right) turn

signal to the grey wire of the left (right) Jet-

stream®.

Connect the black ground wire of the Jet-

stream® to battery ground.

Connect the red 12V supply cable of the Jet-

stream® to the ignition-switched battery plus.

The Jetstream® is now connected. To suppress

the system-related idle current, we recommend

an ignition-controlled i.SED module, which you

can order from www.kellermann-online.com.

Grey - Indicator

Black - Ground

Red - 12V Power Supply

INSTALLATION ELECTRICAL CONNECTION

page 4

Cut the wires between the original indicators

and the wire connectors at a suitable point. By

doing this the wiring loom stays untouched.

Connect your Jetstream® DF as follows:

To connect the wires of the indicator to the

wires of the original connector there are crimp

connectors and shrink tubings included in the

delivery. First push one of the shrink-on tubes

over one of the cables you want to connect and

remove ve millimeter of insulation on the end

of each cable. Then push both bare ends into a

crimp connector and crimp it with an appropriate

tool. Then pull the shrink-on tube over the con-

nection and heat it up equally until it ts tight

over the complete length of the connector.

This type of connection is technically permanent.

To create a non-permanent connection, we re-

commend Posilock wire connectors (not inclu-

ded), which are available for purchase from our

website at www.kellermann-online.com.

Lay the cables in a way, that they are protected

from splash water and fasten them, e.g. by using

zip ties. Now test the function of the Jetstream® DF.

This completes the installation.

•

Connect the positive of the left (right) turn

signal to the grey wire of the left (right) Jet-

stream® DF.

Connect the severed supply line of the rear

light with the grey-white cables of both Jet-

stream® DF.

Connect severed supply line of the brake light

with the grey-red cables of both Jetstream®

DF.

Connect the black ground wire of the Jet-

stream® DF to battery ground.

Connect the red 12V supply cable of the Jet-

stream® DF to the ignition-switched battery plus.

The Jetstream® DF is now connected.To suppress

the system-related idle current, we recommend

an ignition-controlled i.SED module, which you

can order from www.kellermann-online.com.

Grey - Indicator

Grey/White - Rear Position Light

Grey/Red - Brake Light

Black - Ground

Red - 12V Power Supply

ELECTRICAL CONNECTION INDICATOR FLASH RATE

page 4

ELECTRICAL CONNECTION

The ashing frequency can change when con-

verting the original indicators. The installation

of a load-independent asher relay can solve the

problem. If the installation is not possible or not

favored, then parallel connected power resistors

(i.LOAD) will be an option. Only a few vehicles

need special solutions, which we oer as i.SED,

i.BOS and i.LASH products.

ATTENTION! The power resistors will become

very hot after longterm usage of the indicator

lights. Make sure that no components are dama-

ged by this heat.

ATTENTION! The application of the described

measure may interrupt correct functionality,

in the case of a failure causing one of the in-

dicator lights to increase in flash frequency

in order to alert the driver of such a failure.

Before each usage of the vehicle, check the

functionality of the indicator lights.

If you contact us, we will be happy to assist you.

To date, we have been able to help every custo-

mer.

Our team is constantly working on new, impro-

ved solutions for all models and motorcycles. If

you are not sure which electronic equipment you

require, please contact us. Refer to our homepage

at www.kellermann-online.com for additional in-

formation and our online shop with a full range of

spare parts and accessories and a download area.

If you have any suggestions or questions, please

do not hesitate to contact us by email (info@kel-

lermann-online.com) or call us: +49 (0)241/93 80

8-0. We are happy to assist you.

The Kellermann Jetstream® is equipped with the

tried-and-trusted Long Life Protection Guard®

circuit, which ensures extremely long life with LED

technology. It is not necessary to replace the illu-

minate and, due to the laws for device approval,

it is not allowed.

INDICATOR FLASH RATE

ONLINE SHOP at www.kellermann-online.com

Kellermann GmbH

kellermann_company

Jetstream® DFJetstream®

page 5

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali kellermann Accessori per motociclette

kellermann

kellermann KH 1000 Manuale utente

kellermann

kellermann Atto RB Manuale utente

kellermann

kellermann Atto Manuale utente

kellermann

kellermann BL 1000 PL Manuale utente

kellermann

kellermann Bullet 1000 Extreme Manuale utente

kellermann

kellermann Bullet 1000 Extreme Manuale utente

kellermann

kellermann KH 1000 Manuale utente

kellermann

kellermann Rhombus S Dark Manuale utente

kellermann

kellermann Atto DF Integral Manuale utente

kellermann

kellermann Atto Integral Manuale utente

kellermann

kellermann Dayron Manuale utente

kellermann

kellermann micro 1000 LED Manuale utente

kellermann

kellermann Atto WL Manuale utente

kellermann

kellermann Bullet 1000 RB Manuale utente

kellermann

kellermann Rhombus S Extreme Manuale utente

kellermann

kellermann Micro 1000 PL Manuale utente

kellermann

kellermann Bullet Atto RB Manuale utente

kellermann

kellermann micro Rhombus Manuale utente

Manuali Accessori per motociclette popolari di altre marche

SRC

SRC B-TRK502-01-01-SL Manuale utente

3M Speedglas 9100 MP Manuale utente

hepco & becker

hepco & becker 6307520 00 01 Manuale utente

HOMCOM

HOMCOM AA0-077 Manuale utente

hepco & becker

hepco & becker 6307558 00 01 Manuale utente

Wunderkind Custom

Wunderkind Custom 106503-F15 Guida utente

Dräger

Dräger HPS 3500 Manuale utente

M-WAVE

M-WAVE SKI Manuale utente

Kuryakyn

Kuryakyn 6212 Manuale utente

hepco & becker

hepco & becker 6507504 00 01 Manuale utente

Tool it

Tool it PROMAX LCD 9.13G Manuale utente

Custom Dynamics

Custom Dynamics TruWrapz Manuale utente

Roof

Roof RO200 CARBON Manuale utente

Kabuto

Kabuto Japan IBUKI Manuale utente

PUIG

PUIG 5051 Manuale utente

rizoma

rizoma ZTH050 Manuale utente

Joubert

Joubert 10001711 Manuale utente

Sperian

Sperian Optrel p420 Manuale utente

kellermann Jetstream Manuale utente

Manuali Accessori per motociclette popolari di altre marche