Kicker 46KMC3 Manuale utente
Owner’s Manual | English
Manual del Propietario | Español
KMC3 Receptor Multi-Media
Benutzerhandbuch | Deutsch
KMC3 Multi-Media-Receiver
Manuel d’utilisation | Française
KMC3 Multi-Media Receiver
©2020 Stillwater Designs
KMC3
Multi-Media Receiver
KMC3
1
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC Notice - CAN ICES-3 (B) - This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Avis d’Industrie Canada - Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est au-
torisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement. mauvais fonctionnement de I’appareil.
Cet appareil numériquie de la classe B est conforme à la norme NMB-003 du Canada. CAN NMB-3 (B)
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian
information on RF exposure and compliance.
Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 et la conformité à l’exposition de RSS-102 rf, utilisateurs peut
obtenir l’information canadienne sur l’exposition et la conformité de rf.
FCC ID: RGR-KMC3 IC ID: 11078A-KMC3
2
mounting hole cutout template:
3 inches, 7.62 cm
gabarit de montage trou découpé:
3 pouces, 7,62 cm
plantilla de recorte del agujero de montaje:
3 pulgadas, 7.62 cm
montageloch ausschnittschablone :
3 Zoll, 7,62 cm
print mounting hole cutout template at 8.5”x11” in “Portrait” and “Actual Size”
It is recommended you mark the screw holes for Surface Mounting after making the mounting hole.
Imprima la plantilla de recorte del orificio de montaje en tamaño 8.5 x 11 pulgadas, con las opciones de con-
figuración “Vertical” y “Tamaño real”.
imprimer le patron de découpe du trou de fixation au format 8,5”x11” en mode «Portrait» et «Taille réelle».
Drucken Sie die Ausschnittsschablone für das Montageloch bei 8,5” x 11” im Hochformat mit der Einstellung
„Tatsächliche Größe“ aus.
3
mounting hole cutout template:
3 inches, 7.62 cm
gabarit de montage trou découpé:
3 pouces, 7,62 cm
plantilla de recorte del agujero de montaje:
3 pulgadas, 7.62 cm
montageloch ausschnittschablone :
3 Zoll, 7,62 cm
print mounting hole cutout template at 8.5”x11” in “Portrait” and “Actual Size”
It is recommended you mark the screw holes for Surface Mounting after making the mounting hole.
Imprima la plantilla de recorte del orificio de montaje en tamaño 8.5 x 11 pulgadas, con las opciones de con-
figuración “Vertical” y “Tamaño real”.
imprimer le patron de découpe du trou de fixation au format 8,5”x11” en mode «Portrait» et «Taille réelle».
Drucken Sie die Ausschnittsschablone für das Montageloch bei 8,5” x 11” im Hochformat mit der Einstellung
„Tatsächliche Größe“ aus.
4
KMC3 OWNER’S MANUAL
Contents
Specs 5
Overview 6
Installation 7
Operation 10
Troubleshooting 12
Warranty 37
Contenu
Caractéristiques 21
Présentation 22
Installation 23
Utilisation 26
Dépannage 28
Garantie 37
Contenido
Especificaciones 13
Descripción general 14
Instalación 15
Funcionamiento 18
Resolución de problemas 20
Garantía 37
Inhalt
Spezifikationen 29
Übersicht 30
Installation 31
Betrieb 34
Fehlerbehebung 36
Garantie 37
5
Model KMC3
Power Output @ 14.4V, 4Ω stereo, <10% THD+N 25W x 4
Frequency Response [Hz] 20 – 20k
Signal-to-Noise Ratio [dB] 87
Input Sensitivity 500mV
Bluetooth Range [ft] 30
USB Playback MP3, WMA, FLAC, WAV
USB Charging DC 5V, 1A
USB Compatible File System FAT16, FAT32
Line-Out Level [V] 2.5
Outer Trim Ring Dimensions [in, cm] 3.5 x 5.5, 8.89 x 13.97
Protrusion From Mounting Surface [in, cm] 1.25, 3.1
Total Mounting Depth [in, cm] 3.9, 10.1
Be careful not to drill into wiring or vehicle
mechanisms. You are solely responsible for
securely mounting the KMC3 Media Center. See
page 2–3 for mounting hole cutout template.
Before installation, you may wish to plan your
placement of the USB and Auxiliary inputs, and
the optional KRC12 remote (sold separately), for
both convenience and looks!
With a KICKER KXM amplifier, a pair of KICKER
KM speakers, and a few KICKER cables,
you’re looking at a full system upgrade that will
dominate! KICKER amplifiers and accessories
make upgrading a snap. Ask your dealer about
KICKER amplifiers and speaker upgrades to
complete your system!
All specifications and performance figures are
subject to change. Please visit
www.kicker.com for the most current
information.
WARNING: KICKER products are capable of producing
sound levels that can permanently damage your hearing!
Turning up a system to a level that has audible distortion is
more damaging to your ears than listening to an undistorted
system at the same volume level. The threshold of pain is
always an indicator that the sound level is too loud and may
permanently damage your hearing. Please use common
sense when controlling volume.
Authorized KICKER Dealer:
Purchase Date:
Serial Number:
SPECIFICATIONS
6
/SOURCE
MENU
PRESETS
•enter settings menu
•preset menu (AM-FM – press)
•track selection (USB – press)
•save preset menu (AM-FM – press & hold)
•RND/RPT (USB – press & hold)
•power on/off (press & hold)
•change source (press)
•change volume/value (scroll)
•next/previous (scroll)
•select (press)
•enter audio settings menu (press & hold)
•digital display
•seek down (press)
•previous track (press)
•rewind/manual tuning (press & hold)
•seek up (press)
•next track (press)
•fast forward/manual tuning (press & hold)
•play/pause
•mute/unmute
NOTE: Use short and long presses to operate. Some input sources do not support all functions.
OVERVIEW
7
USB input
USB charging
LINE OUT
+12V (switched)
illumination/dimmer
(day/night mode when
wired to vehicle lighting)
rear
right
rear
left
front
right
front
left
AUX IN
radio antenna
ground
fuse
15A ATM
battery
ground
remote auto-turn on output
(to amplifiers)
wired remote
(sold separately)
positive
negative
INSTALLATION
8
1.
2.
Surface Mounting
1. Secure the KMC3 to the surface on which you’re mounting using the supplied screws.
2. Push the faceplate onto the KMC3 until it locks into place.
9
3. Place washers over bolts and securely attach nuts.
4. Depending on the size of your mounting baffle, you may need to snap off one or more of the metal tabs from the mounting bracket to
accomodate installation.
1.
2.3.
4.
Bracket Mounting
1. Attach threaded bolts to the back of the KMC3
2. Position the mounting bracket over the bolts.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Kicker Ricevitore
