KitchenAid KD-100 Manuale utente

KitchenAid,

VALUE DISPOSERS

MODELS KWC=200B, KD-200

KD-100

INSTALLATIONINSTRUCTIONS

INSTALLER: FINAL CHECK LIST

GE.RlcL

emove unit from carton and check for shipping damage.

0 2. Sink flange assembled in center of drain opening and tightly sealed.

0 3. Disposer level - not installed at an angle.

0 4. If a dishwasher drain is connected into the disposer, check to assure that

the inlet knockout has been removed.

PLUMBING

0 1. If installed in old house, existing drain line from sink to sewer cleaned.

0 2. Long, horizontal drain lines eliminated.

0 3. Drum traps and grease traps should not be used.

0 4. Seal at drain spout properly positioned.

0 5. Center line height of drain line must not exceed center line height of

disposer discharge opening.

0 6. M oun mg screws and spout screws properly tightened to prevent leaks.t’

0 7. Compliance with all aspects of local plumbing code.

ELECTRICAL CONNECTION

0 1. Properly fused, 115 volt, 60 hertz branch circuit of 15 ampere capacity.

0 2. Disposer properly grounded before operating.

0 3. All connections must comply with the National Electrical Code and/or

local electrical code.

OPERATIONAL

0 1. Before operating, check to assure grind chamber is free of any foreign

objects.

0 2. Activate disposer -test for grinding performance and water leaks.

THANK YOU INSTALLER:

1. Complete Installation Check List.

2. Leave all literature (including Check List) for customer.

3. Notify dealer that electrical work and plumbing are completed.

GENERALINSTRUCTIONS

1. In old houses it 1sgenerally wise to clean out the existing dram line from sink

to sewer before installing the disposer.

’ The disposer can be installed in a steel. monel, stainless steel, or cast iron sink

having a smh openmg of 3-l/2” to 4” without sink alteration.

3. Standard l-l/3” O.D. or 2” O.D. drain pipe is satisfactory for drain lines. Long

horizontal drain lines should be eliminated. Drum-traps and grease traps should

not be used.

SINKFLANGEASSEMBLY

1 Remove disposer cover (1 ).

2. lnserr screwdriver under lever (10) and pry outward. Disengage hooks (11) and

(7) from support plate (5).

3. Remove existing sink drain connections and clean drain opening.

4. Disassemble items 2. 3. 4, and 5 of mounting assembly by prying snap ring (6)

from groove in sink flange (7).

5. Fil the sink tlange seal (14) to the sink flange (1). Insert sink flange into drain

opening. Be sure the sink flange is located in the center of the drain opening to

assure a water-tight seal. NOTE: The rubber sink flange seal should always be

used where possible. In rare instances where the contour or thickness of the sink

opening does not permit use of the seal. a permanently pliable sealing compound

may be used.

THE SINK FLANGE MUST BE LEVEL BEFORE MOUNTING DISPOSER.

6. Assemble the second sink flange seal (3), pressure washer (4) and support plate

(5) onto the sink flange and lock in place with snap ring (6). Tighten the three

,jack screws (13) EVENLY against pressure washer (4) to secure the mounting

assembly to the sink.

DISHWASHERCONNECTION(IF APPLICABLE)

Connecting the discharge of a dishwasher to a disposer will assure all waste

particles discharged by the dishwasher are properly sized and flushed through to the

main drain system. A dishwasher drain inlet that will accept a 3/4” I.D. hose fitting

is provided in the side of the upper housing grinding chamber for connection of the

dishwasher discharge,

1. Use a small cold chisel or punch to cut out the back wall knockout of the dish-

washer inlet boss of the disposer.

2. Turn the disposer upside down to remove any pieces or chips from the grinding

chamber.

3. KD-100, KD-200. & KWC-2OOB MODELS - Where plumbing codes require, a

3/4” galvanized pipe fitting may be substituted for the plastic fitting (13)

provided. Whel-e plumbing codes permit, use a rubber hose sleeve connection to

prevent transmission of normal operating noise.

NOTE: .A11connections must be in accordance ivith local plumbing codes,

DISPOSER INSTALLATION /

1. Be sure the isolating splash guard (8) is in place. Lift disposer and engage hooh

(7) onto support plate (4), then engage hook (11) onto support plate (4). Turn

disposer to align with drain trap. Snap lever (10) downward to lock.

2. Connect the drain trap to the spout (9). If necessary. pry lever (10) outward

and turn disposer for better alignment.

3. Connect the dishwasher drain hose to the disposer inlet (13) with a hose clamp

(where applicable).

4. Check to assure that the grinding chamber is clean of any foreign objects and tire

flywheel is free to rotate, Place the cover in position and fill the sink at least

three inches deep. Remove the cover and, as the water drains. chech all con

nections for leaks

TYPICAL INSTALLATIONS Height

of drain must not exceed height of

disposer discharge opening.

Typical “P” Trap Connection

Connection With Straight-Away Drain Spout

WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AT THE FUSE/

CIRCUIT BREAKER BOX BEFORE MAKING ELECTRICAL CONNECTIONS.

Follow the National Electrical Code and/or your local electrical code in all details.

In older houses with limited circuits, or if it appears the circuit is heavily loaded,

run a line directly to the main fuse box.

1. Remove the electrical access cover on the bearing bracket assembly.

1,. Install standard strain relief connector (not furnished) into threaded opening in

bearing bracket assembly.

3. Install the control switch where it is easily accessible for the owner. Recom-

mended: On-Off switch suitable for operation of l/2 HP. motor. (Switch not

furnished).

4. Run flexible conduit. or equivalent, from the control switch to the disposer

motor leads located in the bearing bracket assembly. Connect unit to ground

(See illustration and grounding instructions below).

5. Press wires into the electrical access compartment and replace cover.

6. Run flexible conduit, or equivalent, from the control switch to the electrical

power supply. Insulate all connections.

GROUNDING INSTRUCTIONS (Cord - Connected Units)

This appliance must be grounded. In the event of a malfunction or breakdown,

grounding provides a path of least resistance for electric current to reduce the risk

of electric shock. This appliance is equipped with a cord having an equipment

gloundmg conductor and a grounding plug. The plug must be plugged into an

appropriate outlet that is properly installed and grounded in accordance with all

local codes and ordinances.

DANGER: Improper connection of the equipment-grounding conductor can re-

sult in a risk of electric shock, Check with a qualified electrician or serviceman if

you are in doubt as to whether the applicance is properly grounded. Do not

modify the plug provided with the appliance - if it will not fit the outlet, have a

proper outlet installed by a qualified electrician.

GROUNDING INSTRUCTIONS

(Permanent - Connected Units)

This appliance niust be coniie~red to 3

~~roundcd. metal. permanent wiring s

tern: or an equipment-groundiI1~ WE MA.-AL,‘W~~ATLT

du;tor must be rur with the circuit PhS!Ti TT”LPUS,<TO,,’

COI~~~C~~~IS

and connected to rhe equip-

ment-Frounding terminal or lead on Lile

appliance.

KITCHENAID DIVISION \HOBART/

TROY, OHIO 45374

FORM 14609A (1 l-83) PRINTED IN U.S.A.

J/7 7459

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali KitchenAid smaltimento dei rifiuti

KitchenAid

KitchenAid IMPERIAL KCDI075V Manuale utente

KitchenAid

KitchenAid KCDB150 Manuale utente

KitchenAid

KitchenAid TC707S1 Manuale utente

KitchenAid

KitchenAid SUPERBA KCDS075T Manuale utente

KitchenAid

KitchenAid Garbage Disposal Manuale utente

KitchenAid

KitchenAid KCDB250G2 Manuale utente

KitchenAid

KitchenAid KCDB250S1 Manuale utente

KitchenAid

KitchenAid KCDC200 Manuale utente

KitchenAid

KitchenAid KBDS250X - 1 HP Superba Batch Feed Disposer Manuale di installazione

KitchenAid

KitchenAid KBDS100T - NA Batch Feed 1 HP MultiGrind Manuale di servizio

KitchenAid

KitchenAid KCDI075VA Manuale d'uso e manutenzione

KitchenAid

KitchenAid Superba KCDS100T Manuale utente

KitchenAid

KitchenAid KCCC151EBL1 Manuale utente

KitchenAid

KitchenAid KUCS03FSSS Manuale utente

KitchenAid

KitchenAid KCDB250G - Food Waste Disposer Manuale utente

KitchenAid

KitchenAid KCDB250G1 Manuale utente

KitchenAid

KitchenAid KaDette KCDB150 Manuale utente

KitchenAid

KitchenAid KBDS100T - NA Batch Feed 1 HP MultiGrind Manuale utente

KitchenAid

KitchenAid INTEGRATED COMPACTOR Manuale utente

KitchenAid

KitchenAid INTEGRATED COMPACTOR Manuale utente

KitchenAid

KitchenAid KBDS100T - NA Batch Feed 1 HP MultiGrind Manuale utente

KitchenAid

KitchenAid KBDS100T - NA Batch Feed 1 HP MultiGrind Manuale utente

KitchenAid

KitchenAid KCDB250S0 Manuale utente

KitchenAid

KitchenAid KCDS100T0 Manuale utente

Manuali smaltimento dei rifiuti popolari di altre marche

Insinger

Insinger I-6 Manuale utente

Franke

Franke CE-50 Manuale operativo

Leafield Environmental

Leafield Environmental Envirobank 140 Foglio di istruzioni

Meiko

Meiko TopCut B Manuale utente

Gladiator

Gladiator Garage Compactor Manuale utente

Maytag

Maytag DFC1500 Manuale di installazione

Weber mt

Weber mt CR 7 Istruzioni operative

THERMEx

THERMEx WASTEMINATOR II Manuale utente

Weber mt

Weber mt CR 7-II Hd Istruzioni operative

ROBINHOOD

ROBINHOOD SE390 Manuale utente

Whirlpool

Whirlpool GC2000PE2 Manuale utente

Scheppach

Scheppach HP3000S Istruzioni per il montaggio

Haigh

Haigh Quattro Vanguard Original Manuale utente

Maxmatic

Maxmatic 5000 Scheda tecnica

InSinkErator

InSinkErator Model SS-100 Manuale utente

Toro

Toro FP-2200 Manuale utente

Elephants Foot

Elephants Foot eDiverter Manuale utente

Zanussi

Zanussi DU 4400 Manuale utente