KMC Controls CSC-3501 Manuale utente

Installation Guide

Linear Reset Volume Controllers

CSC-3501, 3505

Mounting

The CSC-3501 and 3505 are position sensitive. They are calibrated to be mounted in a horizontal plane

with the face down. Any other orientation will require recalibration of the “branch balance”.

1. Connect the right angle bracket to the mounting surface with 2 self threading screws in the two 13/64"

(5 mm) mounting holes.

2. Insert the controller, face down.

3. Make sure to leave enough room to make connections.

Connections

For model CSC-3501, 3505 use 1/4" (5 mm) O.D. “FR”

tubing, on the following push-on fittings:

1. Connect the clean, dry, main air supply to Port “M”.

2. Connect the damper actuator to Port “B”.

3. Connect the Thermostat output to Port “T”.

4. Connect the total pressure tap on the air flow sensor

to Port “H”.

5. Connect the static pressure tap on the air flow

sensor to Port “L”.

Adjustments and Calibration

Damper Action

The damper action is factory set at Normally Open (N.O.). To field select Normally Closed (N.C.):

1. Loosen damper selection screw

2. Turn selection dial clockwise until the “NC” arrow aligns with the “Damper” arrow.

3. Tighten selection screw.

To Adjust Branch Balance:

1. Disconnect thermostat from Port “T”

2. Disconnect ∆P sensor such that “H” and “L” are at 0" WC.

3. Adjust “LO STAT” knob fully Clockwise (CW)

4. Adjust branch balance for midpoint of actuator span +/- 2.5 psig (7.5 psi for 5–10 psi span,

10.5 psi for 8– 13 psi span).

5. Reconnect Ports “H”, “L” and “T”

KMC Controls

P.O. Box 497

19476 Industrial Drive

New Paris, IN 46553

574.831.5250

www.kmccontrols.com

221-019-01C

Adjustments and Calibration Continued

To Adjust Reset Start:

Thermostat Reset Start Point is factory Set at 8 psi.

1. Remove cap on Port “G” port

2. Connect to a 0– 30 psi gauge

3. Apply desired thermostat start point pressure to

Port “T”

3. Adjust “Reset Start” until gauge pressure increases

slightly (0.3 psig maximum).

4. Disconnect gauge and replace Port “G” cap

To Adjust Reset Span:

Thermostat Reset Span is factory set at 5 psig.

1. Remove Port “G” cap

2. Connect accurate 0–30 psi gauge.

3. Set thermostat for a Port “T” pressure of 15–30 psig.

4. Adjust “Reset Span” until gage pressure indicates the

desired span. This is total span pressure, not ending

pressure.

NOTE: An increase or decease of a 5 psig reset span will directly affect the differential pressure range.

Increasing the span to 7 psi will double the range, decreasing the span to 3.5 psi will halve the range.

5. Disconnect gauge and replace Port “G” cap

To Adjust Minimum and Maximum Limits:

1. Disconnect thermostat from Port “T” port

2 Adjust LO STAT ∆P:

For DA cooling or RA heating applications, adjust “LO STAT ∆P for minimum flow.

For RA cooling or DA heating applications, adjust “LO STAT ∆P” for maximum flow.

3. Set thermostat for a Port “T” pressure of 15–30 psig.

4. Adjust HI STAT ∆P:

For DA cooling or RA heating applications, adjust “HI STAT ∆P” for maximum flow.

For RA cooling or DA heating applications, adjust “HI STAT ∆P” for minimum flow.

NOTE:For maximum accuracy/repeatability, repeat/check minimum and maximum limit adjustments

twice. “LO STAT ∆P” must be adjusted first followed by “HI STAT ∆P” adjustment. “LO STAT ∆P”

adjustments affect “HI STAT ∆P” settings.

Maintenance

No routine maintenance is required.

Each component is designed and manufactured for

reliability and performance. Careful installation and

use will ensure long term dependability.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali KMC Controls Controllori

KMC Controls

KMC Controls BAC-7003 Manuale utente

KMC Controls

KMC Controls BAC-7302 Istruzioni operative

KMC Controls

KMC Controls SimplyVAV BAC-8001 Manuale utente

KMC Controls

KMC Controls KMD-5205 Istruzioni operative

KMC Controls

KMC Controls CSC-2000 Series Manuale utente

KMC Controls

KMC Controls MEP-46 Q Series Manuale utente

KMC Controls

KMC Controls FlexStat BAC-120063CW-ZEC Manuale dell'operatore

KMC Controls

KMC Controls MCP-1020 Series Manuale utente

KMC Controls

KMC Controls BAC-5901C-AFMS Manuale utente

KMC Controls

KMC Controls MEP-4 Series Guida utente

KMC Controls

KMC Controls AppStat Manuale utente

KMC Controls

KMC Controls MEP-7 Series Guida utente

KMC Controls

KMC Controls MEP-1500 Series Manuale utente

KMC Controls

KMC Controls BAC-7001 Manuale utente

KMC Controls

KMC Controls CSC-1001 Manuale utente

KMC Controls

KMC Controls MCP-1160 Series Manuale utente

KMC Controls

KMC Controls MCP-1040 Series Manuale utente

KMC Controls

KMC Controls KMD-5290 Manuale utente

KMC Controls

KMC Controls BAC-4000 series Guida utente

KMC Controls

KMC Controls MEP-4201 Manuale utente

KMC Controls

KMC Controls MEP-3001 Istruzioni operative

KMC Controls

KMC Controls BAC-9300 Series Manuale utente

KMC Controls

KMC Controls KMDigital KMD-5290E Istruzioni operative

KMC Controls

KMC Controls CTE-3017 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente