KMC Controls MEP-3001 Istruzioni operative

MEP-3001/3006 1 Installation and Operation Guide

Installation and Operation Guide

Thermic 2-Position or Time-Proportional Actuators

MEP-3001 (for VEP-12/22/34) and MEP-3006 (for VEP-11/21/37)

Mounting 1

Wiring 1

Operation 2

Maintenance 2

Select Speciﬁcations2

More Information 2 CAUTION

If mounting the actuator to a valve already in-line,

close the shut-off valves in the piping (upstream

ﬁrst, then downstream) or switch off the pump to

allow the differential pressure in the valve to drop.

CAUTION

To prevent condensation from dripping onto the

actuator housing, mount the valve with the actuator

in the upright position or, at most, at a 45° angle.

1a. On a new valve body, remove the protective cap

covering the bonnet. (See Illustration 2.)

1b. To remove an existing (same model) actuator,

disconnect the wiring, wait at least six minutes

until the actuator has completely cooled, turn

the actuator bayonet ring (coupling piece)

counterclockwise until it is loose, and pull o the

actuator. Also unscrew the old black bayonet nut

if it stays on.

2a. If the new black bayonet nut is loose from the

new actuator, screw it on top of the valve body

and rmly hand-tighten (only). (See Illustration

3.) Then place the actuator over it and turn the

actuator bayonet ring clockwise until it is hand-

tight and locks into place.

2b. If the new black bayonet nut is rmly aached

inside the actuator, screw the entire actuator on

top of the valve body until it is hand-tight and

locks into place.

Mounting

Wiring

Connect the brown wire to the phase side of 24 VAC

and the blue wire to neutral. (See Illustration 1.)

For two-position control, a simple switch or relay

can be used. For time-proportional (pulse-width

modulation) control, use a KMC REE-5017 or

REE-4106/5106 relay module. (See the relevant relay

module documentation for more information.)

NOTE: All wiring must conform to NEC and

local codes and regulations. Use a Class 2

transformer.

Illustration 1—Dimensions and Wiring

Illustration 2—Removing a Protective Cap

Illustration 3—Installing the Black Bayonet Nut

Brown to 24 VAC Phase

Blue to 24 VAC Neutral

MEP-3001/3006 2 Installation and Operation Guide

KMC Controls, Inc.

19476 Industrial Drive

New Paris, IN 46553

574.831.5250

www.kmccontrols.com; [email protected]

Maintenance

These actuators are noise-free and maintenance-free.

Careful installation will help ensure long-term reli-

ability and performance.

Operation

After the mechanical and electrical installations have

been completed, cycle the actuator to verify opera-

tion. (See Illustrations 4 and 5.)

When power is applied to the actuator, the tem-

perature of the heating element rises, causing the

solid expansion medium to expand and stroke the

aached valve body. The valve starts to open after

preheating for approximately 1 minute if the heating

element is switched on in a cold (room temperature)

state, and achieves the maximum stroke after (ap-

proximately) another 3-1/2 minutes. At power-o,

the expansion element cools down, and the spring

closes the valve.

De-energized position (gap closed):

• For MEP-3001s, the actuator shaft

is extended and the valve is closed.

• For MEP-3006s, the actuator shaft

is retracted and the valve is open.

(Fully) energized position (gap open):

• The MEP-3001 has been connected

to the power supply for at least

4-1/2 minutes. The actuator shaft is

retracted and the valve is open.

• The MEP-3006 has been connected

to the power supply for at least

4-1/2 minutes. The actuator shaft is

extended and the valve is closed.

Select Speciﬁcations

Power 24 VAC (± 20%), 50/60 Hz,

Class 2 only, 6 VA max.

Control Two-position or time-propor-

tional

Primary Fuse Must supply externally

Nominal Force 22.5 in-lb. (100 N•m)

Stroke Maximum 0.18 inches (4.5 mm)

Positioning Time 270 sec. @ 68° F (20° C)

Weight 0.4 lb. (0.18 kg)

Mounting Location NEMA 3 (IP54), interior only

Approvals Conforms to CE requirements

De-energized Position

MEP-3001 (NC) Actuator shaft extended, valve

closed (for VEP-12/22/34 se-

ries)

MEP-3006 (NO) Actuator shaft retracted, valve

open (for VEP-11/21/37 series)

Temperature Limits

Medium 34 to 230° F (1 to 110° C)

Ambient 41 to 122° F (5 to 50° C) @ 0 to

85% RH (non-condensing)

Shipping –4 to 140° F (–20 to 60° C) @ 0

to 95% RH (non-condensing)

Illustration 4—Position Indication

Illustration 5—Opening and Closing Times

More Information

For more information

on applications, see the

REE-5017 on the KMC

web site.

See also, the REE-5106.

Questo manuale è adatto per i seguenti modelli

Altri manuali KMC Controls Controllori

KMC Controls

KMC Controls FlexStat BAC-120063CW-ZEC Manuale dell'operatore

KMC Controls

KMC Controls CSC-1001 Manuale utente

KMC Controls

KMC Controls MEP-5062 Manuale utente

KMC Controls

KMC Controls CSC-3501 Manuale utente

KMC Controls

KMC Controls CSC 3000 Series Guida utente

KMC Controls

KMC Controls MEP-4201 Manuale utente

KMC Controls

KMC Controls AppStat Manuale utente

KMC Controls

KMC Controls CSP-4702 Manuale utente

KMC Controls

KMC Controls MEP-1500 Series Manuale utente

KMC Controls

KMC Controls MCP-1020 Series Manuale utente

KMC Controls

KMC Controls BAC-7001 Manuale utente

KMC Controls

KMC Controls CEE-3009 Manuale utente

KMC Controls

KMC Controls SimplyVAV BAC-8205 Manuale utente

KMC Controls

KMC Controls MEP-7 Series Guida utente

KMC Controls

KMC Controls BAC-5900 Series Manuale utente

KMC Controls

KMC Controls MEP-4201 Manuale utente

KMC Controls

KMC Controls MCP-1160 Series Manuale utente

KMC Controls

KMC Controls BAC-9300 Series Manuale utente

KMC Controls

KMC Controls BAC-9001CE Manuale utente

KMC Controls

KMC Controls KMDigital KMD-5290E Istruzioni operative

KMC Controls

KMC Controls CSC-2000 Series Manuale utente

KMC Controls

KMC Controls KMD-7001 Istruzioni operative originali

KMC Controls

KMC Controls BAC-5901C-AFMS Manuale utente

KMC Controls

KMC Controls FlexStat BAC-12 63 Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente