KMC Controls MCP-1060 Series Manuale utente

MCP-1060 Series 1 Installation Guide

Installation Guide

6" Pneumatic Damper Actuator

MCP-1060 Series

Mounting

The MCP-1160 series actuator MUST be mounted on

a rigid surface due to the force generated at, or near,

maximum air pressure.

1. Align the actuator with the controlled device. The

mounting joint allows the actuator to be located

in a dierent plane from the controlled device.

2. Aach the actuator to the rigid surface.

3. Adjust the crank arm assembly length (see the

chart) to provide the (minimum 60° to maximum

120°) rotation as required.

4. Do NOT tighten the universal joint. The actuator

must be free to swivel as it operates.

5. See the Connection section on the next page.

All dimension are in inches (mm)

CAUTION

Pneumatic devices must be supplied with clean, dry

control air. Any other medium (e.g., oil or moisture

contamination) will cause the device to fail.

CLEVIS

FEEDBACK SPRING

ALTERNATE

FEEDBACK

SPRING

CRANK ARM

BRACKET

MOUNTING POST

(Not Included)

MCP-1060 Series 2 Installation Guide

Important Notices

The material in this document is for information pur-

poses only. The contents and the product it describes

are subject to change without notice. KMC Controls,

Inc. makes no representations or warranties with respect

to this document. In no event shall KMC Controls, Inc.

be liable for any damages, direct or incidental, arising

out of or related to the use of this document.

Maintenance

No routine maintenance is required. However,

care should be taken during any installation or

maintenance due to the power of the actuator. Each

component is designed for dependable, long-term

reliability, and performance. Careful installation will

also ensure long-term reliability and performance.

Adjustments and Calibration

DANGER

The MCP-1060 contains a large powerful spring.

Exercise extreme caution if disassembly is required.

The actuator shaft MUST be restrained to prevent

the spring from expanding.

To change the positioner start-point:

1. Apply the desired signal pressure.

2. Rotate the start-point adjuster until the actuator

starts to stroke.

More Information

For specications and other information about the

actuators, see the MCP-1160 Series Data Sheet on

the KMC web site. For information about the posi-

tioner, see CMC-1001 Data Sheet.

KMC Controls, Inc.

19476 Industrial Drive

New Paris, IN 46553

574.831.5250

www.kmccontrols.com

[email protected]

Connections

NOTE: Use 1/4" (6 mm) O.D. FR polyethylene

tubing and only clean, dry control air.

NOTE: MCP-1160 models ordered with CMC-1001

positioners are factory-piped between the

positioner and the actuator.

1. Connect the input control signal to the actuator

port (if no positioner is used) or to the positioner

(CMC-1001 input) Port 2(see the diagram).

2. Connect the main air (20 psi) to the positioner

(CMC-1001 center) port.

3. If a positioner is not factory-piped to the actuator,

connect the actuator input port to positioner

(CMC-1001 output) Port 1.

NOTE: If the application requires operation near

the maximum temperature and maximum

pressure, add a tubing restraint to the

actuator connection.

The MCP-1160 contains an 8-13 psi spring. A CMC-

1001 positioner allows the unit to operate over any 5

psi span with the start-point adjustable from 3-10 psi.

Replace the 5 psi spring with a 7 or 10 psi spring to

widen the span.

Altri manuali KMC Controls Controllori

KMC Controls

KMC Controls SimplyVAV BAC-8001 Manuale utente

KMC Controls

KMC Controls CEE-3009 Manuale utente

KMC Controls

KMC Controls CSP-4702 Manuale utente

KMC Controls

KMC Controls BAC-7401 Istruzioni operative

KMC Controls

KMC Controls BAC-7302 Istruzioni operative

KMC Controls

KMC Controls MEP-3001 Istruzioni operative

KMC Controls

KMC Controls KMD-5210 Istruzioni operative

KMC Controls

KMC Controls KMDigital KMD-5290E Istruzioni operative

KMC Controls

KMC Controls FlexStat BAC-120063CW-ZEC Manuale dell'operatore

KMC Controls

KMC Controls MEP-1500 Series Manuale utente

KMC Controls

KMC Controls MEP-7 Series Guida utente

KMC Controls

KMC Controls KMD-5831 Istruzioni operative originali

KMC Controls

KMC Controls CSC-3501 Manuale utente

KMC Controls

KMC Controls KMD-5205 Istruzioni operative

KMC Controls

KMC Controls CSC-1001 Manuale utente

KMC Controls

KMC Controls CSC 3000 Series Guida utente

KMC Controls

KMC Controls MEP-46 Q Series Manuale utente

KMC Controls

KMC Controls BAC-7003 Manuale utente

KMC Controls

KMC Controls MEP-5062 Manuale utente

KMC Controls

KMC Controls SimplyVAV BAC-8205 Manuale utente

KMC Controls

KMC Controls SimplyVAV BAC-8001 Guida utente

KMC Controls

KMC Controls BAC-9300 Series Manuale utente

KMC Controls

KMC Controls MCP-1160 Series Manuale utente

KMC Controls

KMC Controls FlexStat BAC-12 63 Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente